main
Ray
Publish 0.1.0
dbbb1f5
KTH4621BAT-ST6
CONNTEK · Magnetic Angle Sensors · SOT-23-6L
KTH4621BAT-ST6 from CONNTEK, in a SOT-23-6L. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDD | power_in | Supply pin, operating range 2.5 V to 5.5 V with respect to GND (absolute maximum VDD is 6 V); the datasheet recommends a 1 uF capacitor between VDD and GND placed close to the pin. |
| 2 | TEST | passive | Test pin, which the datasheet pin table specifies must be connected to ground. |
| 3 | NC | unconnected | Listed as NC in the name column, but the datasheet pin table specifies it must be connected to ground. |
| 4 | OUT1 | output | For KTH4621B this is the Z-axis latched switch output (NMOS open-drain); it goes low when the field exceeds BOP (25 Gs typ., 40 Gs max) and stays low, and goes high when the field drops below BRP (-25 Gs typ., -40 Gs min); output drive current is limited to 30 mA absolute maximum. |
| 5 | GND | power_in | Ground reference for all voltages on the device (all absolute maximum voltages are referenced to GND). |
| 6 | OUT2 | output | For KTH4621B this is the X-axis latched switch output (NMOS open-drain) with the same latched BOP/BRP switching behaviour as OUT1; output drive current is limited to 30 mA absolute maximum. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | CONNTEK |
| Package | SOT-23-6L |
| Category | Magnetic Sensors |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage (operating state) | VDD | 2.5 | 3.3 | 5.5 | V | 工作状态 | 8 |
| Output low voltage | VOL | 0.01 | 0.05 | V | IOUT=1mA | 8 | |
| Magnetic operate point (South pole left, bottom or marked side facing, Fig 14-1) | BOP(out1)/BOP(out2) | 25 | 40 | GS | 南极向左,底部或有打印标记的面侧(参见图 14-1) | 9 | |
| Magnetic release point (South pole left, bottom or marked side facing, Fig 14-1) | BRP(out1)/BRP(out2) | -40 | -25 | GS | 南极向左,底部或有打印标记的面侧(参见图 14-1) | 9 | |
| Absolute max supply voltage (referenced to GND) | VDD | -0.3 | 6 | V | TA=25℃,列出的电压均以 GND 为参考 | 7 | |
| Absolute max output drive current | IOUTPUT | 30 | mA | TA=25℃ | 7 | ||
| Storage temperature range | TSTG | -50 | 150 | ℃ | TA=25℃ | 7 | |
| Maximum junction temperature | TJ | 150 | ℃ | TA=25℃ | 7 | ||
| ESD capability, human body model | ESD HBM | -6000 | 6000 | V | HBM 人体模型 | 7 | |
| Recommended supply voltage range | VDD | 2.5 | 5.5 | V | 芯片工作 | 8 | |
| Recommended operating temperature range | TA | -40 | 125 | oC | 芯片工作 | 8 |
CAD (land: KiCad; 3D: generated from the datasheet)
- Symbol:
KTH4621BAT-ST6 - Footprint:
Package_TO_SOT_SMD:SOT-23-6 - 3D model: SOT-23-6L, generated on the KiCad land (body 1.61 x 2.92 mm, terminals on the pads, 1.165 mm tall, datasheet A, midpoint of min and max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
kth4621bat-st6-etched.step/kth4621bat-st6-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);kth4621bat-st6.step/kth4621bat-st6.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: CONNTEK datasheet (15 pp, sha256
a3e3aabd858be7d4, retrieved 2026-11-13, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).
# KTH4621BAT-ST6
**CONNTEK** · Magnetic Angle Sensors · SOT-23-6L
KTH4621BAT-ST6 from CONNTEK, in a SOT-23-6L. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDD | power_in | Supply pin, operating range 2.5 V to 5.5 V with respect to GND (absolute maximum VDD is 6 V); the datasheet recommends a 1 uF capacitor between VDD and GND placed close to the pin. |
| 2 | TEST | passive | Test pin, which the datasheet pin table specifies must be connected to ground. |
| 3 | NC | unconnected | Listed as NC in the name column, but the datasheet pin table specifies it must be connected to ground. |
| 4 | OUT1 | output | For KTH4621B this is the Z-axis latched switch output (NMOS open-drain); it goes low when the field exceeds BOP (25 Gs typ., 40 Gs max) and stays low, and goes high when the field drops below BRP (-25 Gs typ., -40 Gs min); output drive current is limited to 30 mA absolute maximum. |
| 5 | GND | power_in | Ground reference for all voltages on the device (all absolute maximum voltages are referenced to GND). |
| 6 | OUT2 | output | For KTH4621B this is the X-axis latched switch output (NMOS open-drain) with the same latched BOP/BRP switching behaviour as OUT1; output drive current is limited to 30 mA absolute maximum. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | CONNTEK |
| Package | SOT-23-6L |
| Category | Magnetic Sensors |
| Pins | 6 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage (operating state) | VDD | 2.5 | 3.3 | 5.5 | V | 工作状态 | 8 |
| Output low voltage | VOL | | 0.01 | 0.05 | V | IOUT=1mA | 8 |
| Magnetic operate point (South pole left, bottom or marked side facing, Fig 14-1) | BOP(out1)/BOP(out2) | | 25 | 40 | GS | 南极向左,底部或有打印标记的面侧(参见图 14-1) | 9 |
| Magnetic release point (South pole left, bottom or marked side facing, Fig 14-1) | BRP(out1)/BRP(out2) | -40 | -25 | | GS | 南极向左,底部或有打印标记的面侧(参见图 14-1) | 9 |
| Absolute max supply voltage (referenced to GND) | VDD | -0.3 | | 6 | V | TA=25℃,列出的电压均以 GND 为参考 | 7 |
| Absolute max output drive current | IOUTPUT | | | 30 | mA | TA=25℃ | 7 |
| Storage temperature range | TSTG | -50 | | 150 | ℃ | TA=25℃ | 7 |
| Maximum junction temperature | TJ | | | 150 | ℃ | TA=25℃ | 7 |
| ESD capability, human body model | ESD HBM | -6000 | | 6000 | V | HBM 人体模型 | 7 |
| Recommended supply voltage range | VDD | 2.5 | | 5.5 | V | 芯片工作 | 8 |
| Recommended operating temperature range | TA | -40 | | 125 | oC | 芯片工作 | 8 |
## CAD (land: KiCad; 3D: generated from the datasheet)
- Symbol: `KTH4621BAT-ST6`
- Footprint: `Package_TO_SOT_SMD:SOT-23-6`
- 3D model: SOT-23-6L, generated on the KiCad land (body 1.61 x 2.92 mm, terminals on the pads, 1.165 mm tall, datasheet A, midpoint of min and max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files: `kth4621bat-st6-etched.step` / `kth4621bat-st6-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `kth4621bat-st6.step` / `kth4621bat-st6.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [CONNTEK datasheet](docs/kth4621bat-st6-datasheet.pdf) (15 pp, sha256 `a3e3aabd858be7d4`, retrieved 2026-11-13, tier: lcsc)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).
[Datasheet PDF](docs/kth4621bat-st6-datasheet.pdf)