Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

KTH4621BAT-ST6

CONNTEK · Magnetic Angle Sensors · SOT-23-6L

KTH4621BAT-ST6 from CONNTEK, in a SOT-23-6L. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.

Pinout

Pin Name Type Function
1 VDD power_in Supply pin, operating range 2.5 V to 5.5 V with respect to GND (absolute maximum VDD is 6 V); the datasheet recommends a 1 uF capacitor between VDD and GND placed close to the pin.
2 TEST passive Test pin, which the datasheet pin table specifies must be connected to ground.
3 NC unconnected Listed as NC in the name column, but the datasheet pin table specifies it must be connected to ground.
4 OUT1 output For KTH4621B this is the Z-axis latched switch output (NMOS open-drain); it goes low when the field exceeds BOP (25 Gs typ., 40 Gs max) and stays low, and goes high when the field drops below BRP (-25 Gs typ., -40 Gs min); output drive current is limited to 30 mA absolute maximum.
5 GND power_in Ground reference for all voltages on the device (all absolute maximum voltages are referenced to GND).
6 OUT2 output For KTH4621B this is the X-axis latched switch output (NMOS open-drain) with the same latched BOP/BRP switching behaviour as OUT1; output drive current is limited to 30 mA absolute maximum.

Key specifications

Parameter Value
Manufacturer CONNTEK
Package SOT-23-6L
Category Magnetic Sensors
Pins 6

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage (operating state) VDD 2.5 3.3 5.5 V 工作状态 8
Output low voltage VOL 0.01 0.05 V IOUT=1mA 8
Magnetic operate point (South pole left, bottom or marked side facing, Fig 14-1) BOP(out1)/BOP(out2) 25 40 GS 南极向左,底部或有打印标记的面侧(参见图 14-1) 9
Magnetic release point (South pole left, bottom or marked side facing, Fig 14-1) BRP(out1)/BRP(out2) -40 -25 GS 南极向左,底部或有打印标记的面侧(参见图 14-1) 9
Absolute max supply voltage (referenced to GND) VDD -0.3 6 V TA=25℃,列出的电压均以 GND 为参考 7
Absolute max output drive current IOUTPUT 30 mA TA=25℃ 7
Storage temperature range TSTG -50 150 ℃ TA=25℃ 7
Maximum junction temperature TJ 150 ℃ TA=25℃ 7
ESD capability, human body model ESD HBM -6000 6000 V HBM 人体模型 7
Recommended supply voltage range VDD 2.5 5.5 V 芯片工作 8
Recommended operating temperature range TA -40 125 oC 芯片工作 8

CAD (land: KiCad; 3D: generated from the datasheet)

  • Symbol: KTH4621BAT-ST6
  • Footprint: Package_TO_SOT_SMD:SOT-23-6
  • 3D model: SOT-23-6L, generated on the KiCad land (body 1.61 x 2.92 mm, terminals on the pads, 1.165 mm tall, datasheet A, midpoint of min and max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: kth4621bat-st6-etched.step / kth4621bat-st6-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); kth4621bat-st6.step / kth4621bat-st6.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: CONNTEK datasheet (15 pp, sha256 a3e3aabd858be7d4, retrieved 2026-11-13, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).

Datasheet PDF