main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers isl95810uiu8z-t: viewers · Ray
isl95810uiu8z-t-etched.glb Publish 0.1.0 · Ray
isl95810uiu8z-t-etched.step isl95810uiu8z-t: factory component page (tier=lcsc) · Ray
isl95810uiu8z-t-hero.glb isl95810uiu8z-t: hero GLB from the etched model (keeps the MPN mark) · Ray
isl95810uiu8z-t-hero.overlay.json Publish 0.1.0 · Ray
isl95810uiu8z-t.glb Publish 0.1.0 · Ray
isl95810uiu8z-t.kicad_mod Publish 0.1.0 · Ray
isl95810uiu8z-t.kicad_sym Publish 0.1.0 · Ray
isl95810uiu8z-t.lbr Publish 0.1.0 · Ray
isl95810uiu8z-t.step Publish 0.1.0 · Ray
package.json Publish 0.1.1 · Ray
page.json Publish 0.1.1 · Ray
README.md Publish 0.1.0 · Ray
verification.json Verified: Published by the parts factory: tier lcsc, 8 pins · Ray

ISL95810UIU8Z-T

RENESAS · Digital Potentiometers · MSOP-8

ISL95810UIU8Z-T from RENESAS, in a MSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 WP input Hardware write protection, active low; it must be HIGH to perform any Write operation, and when LOW the device ignores write data bytes and goes to standby.
2 SCL input I2C interface clock input, with a maximum SCL frequency of 400 kHz.
3 SDA bidirectional Serial data I/O for the I2C interface.
4 GND power_in Ground reference for the device.
5 RW passive Wiper terminal of the digitally controlled potentiometer; voltage at this DCP pin must stay between VSS and VCC, and wiper current is limited to ±3.0 mA.
6 RL passive Low terminal of the digitally controlled potentiometer; voltage at this DCP pin must stay between VSS and VCC.
7 RH passive High terminal of the digitally controlled potentiometer; voltage at this DCP pin must stay between VSS and VCC.
8 VCC power_in Power supply, 2.7 V to 5.5 V.

Key specifications

Parameter Value
Manufacturer RENESAS
Package MSOP-8
Category Data Converters
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
RH to RL Resistance Tolerance -20 20 % 3
Wiper Resistance RW 70 200 Ω VCC = 3.3V at +25°C; wiper current = VCC/RTOTAL 3
Integral Non-Linearity (voltage divider) INL -1 1 LSB Voltage divider mode (0V at RL; VCC at RH; measured at RW, unloaded) 3
Differential Non-Linearity (voltage divider), U option DNL -0.5 LSB Monotonic over all tap positions 3
Zero-Scale Error, U option ZSerror 0 0.5 2 LSB 3
Full-Scale Error, U option FSerror -2 -0.5 0 LSB 3
Ratiometric Temperature Coefficient TCV -4 4 ppm/°C DCP Register set to 80 hex 3
Resistor Mode Integral Non-Linearity RINL -1 1 MI DCP register set between 20 hex and FF hex. Monotonic over all tap positions 3
Resistor Mode Differential Non-Linearity, U option RDNL -0.5 MI DCP register set between 20 hex and FF hex. Monotonic over all tap positions 3
Offset, U option Roffset 0 0.5 2 MI 3
Resistance Temperature Coefficient TCR -165 165 ppm/°C DCP register set between 20 hex and FF hex 3
DCP Leakage Current ILkgDCP 0.1 1 µA Voltage at pin from GND to VCC 3
VCC Supply Current (Volatile write/read) ICC1 1 mA fSCL = 400kHz; SDA = Open; (for I2C, Active, Read and Volatile Write States only) 4
VCC Supply Current (Nonvolatile Write) ICC2 3 mA fSCL = 400kHz; SDA = Open; (for I2C, Active, Nonvolatile Write State only) 4
VCC Current (Standby) ISB 5 µA VCC = +5.5V, I2C Interface in Standby State 4
VCC Current (Standby) ISB 2 µA VCC = +3.6V, I2C Interface in Standby State 4
Leakage Current, at Pins SDA, SCL, and WP ILkgDig -10 10 µA Voltage at pin from GND to VCC 4
DCP Wiper Response Time tDCP 1 µs SCL falling edge of last bit of DCP Data Byte to wiper change 4
Power-On Recall Voltage Vpor 1.8 2.6 V Minimum VCC at which memory recall occurs 4
VCC Ramp Rate VCCRamp 0.2 V/ms 4
Power-Up Delay tD 3 ms VCC above Vpor, to DCP Initial Value Register recall completed, and I2C Interface in standby state 4
Input Buffer LOW Voltage (WP, SDA, SCL) VIL -0.3 V 4
SDA Output Buffer LOW Voltage VOL 0 0.4 V Sinking 4mA 4
SCL Frequency fSCL 400 kHz 4
Pulse Width Suppression Time at SDA and SCL Inputs tIN 50 ns Any pulse narrower than the max spec is suppressed 4
SCL Falling Edge to SDA Output Data Valid tAA 900 ns SCL falling edge crossing 30% of VCC, until SDA exits the 30% to 70% of VCC window 4
Time the Bus Must be Free Before a New Transmission tBUF 1300 ns SDA crossing 70% of VCC during a STOP condition, to SDA crossing 70% of VCC during the following START condition 4
Clock LOW Time tLOW 1300 ns Measured at the 30% of VCC crossing 4
Clock HIGH Time tHIGH 600 ns Measured at the 70% of VCC crossing 4
START Condition Setup Time tSU:STA 600 ns SCL rising edge to SDA falling edge. Both crossing 70% of VCC 4
START Condition Hold Time tHD:STA 600 ns From SDA falling edge crossing 30% of VCC to SCL falling edge crossing 70% of VCC 4
Input Data Setup Time tSU:DAT 100 ns From SDA exiting the 30% to 70% of VCC window, to SCL rising edge crossing 30% of VCC 4
Input Data Hold Time tHD:DAT 0 ns From SCL rising edge crossing 70% of VCC to SDA entering the 30% to 70% of VCC window 4
STOP Condition Setup Time tSU:STO 600 ns From SCL rising edge crossing 70% of VCC, to SDA rising edge crossing 30% of VCC 4
STOP Condition Hold Time for Read, or Volatile Only Write tHD:STO 600 ns From SDA rising edge to SCL falling edge. Both crossing 70% of VCC 4
STOP Condition Hold Time for Non-Volatile Write tHD:STO:NV 2 µs From SDA rising edge to SCL falling edge. Both crossing 70% of VCC 4
Output Data Hold Time tDH 0 ns From SCL falling edge crossing 30% of VCC, until SDA enters the 30% to 70% of VCC window 5
SDA and SCL Rise Time tR 250 ns From 30% to 70% of VCC 5
SDA and SCL Fall Time tF 250 ns From 70% to 30% of VCC 5
Capacitive Loading of SDA or SCL Cb 10 400 pF Total on-chip and off-chip 5
SDA and SCL Bus Pull-Up Resistor Off-Chip Rpu 1 kΩ Maximum is determined by tR and tF 5
Non-Volatile Write Cycle Time tWP 12 20 ms 5
WP Setup Time tSU:WP 600 ns Before START condition 5
WP Hold Time tHD:WP 600 ns After STOP condition 5
Storage Temperature -65 150 °C 3
VCC Absolute Maximum VCC -0.3 6 V 3
Voltage at Any Digital Interface Pin -0.3 V With respect to VSS; upper limit printed as VCC+0.3 3
Voltage at Any DCP Pin -0.3 V With respect to VSS; upper limit printed as VCC 3
Wiper Current (10s, absolute maximum) IW -6 6 mA 10s 3
Lead Temperature (Soldering) 300 °C Soldering, 10s 3
Industrial Operating Temperature -40 85 °C Industrial 3
VCC Supply Voltage VCC 2.7 5.5 V 3
Power Rating of Each DCP 5 mW 3
Wiper Current of Each DCP -3 3 mA Printed as ±3.0 mA 3
Thermal Resistance Junction-to-Ambient, 8 Ld MSOP θJA 151 °C/W 8 Ld MSOP Package (Notes 6, 7) 3
Thermal Resistance Junction-to-Case, 8 Ld MSOP θJC 50 °C/W 8 Ld MSOP Package (Notes 6, 7) 3

CAD (KiCad official)

  • Symbol: ISL95810UIU8Z-T
  • Footprint: Package_SO:MSOP-8_3x3mm_P0.65mm
  • 3D model: MSOP-8 (KiCad packages3D, STEP)
  • 3D model files: isl95810uiu8z-t-etched.step / isl95810uiu8z-t-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); isl95810uiu8z-t.step / isl95810uiu8z-t.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: RENESAS datasheet (15 pp, sha256 0d23c3dc6b740eba, retrieved 2026-10-30, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF