3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownISL95810UIU8Z-T
RENESAS · Digital Potentiometers · MSOP-8
ISL95810UIU8Z-T from RENESAS, in a MSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | WP | input | Hardware write protection, active low; it must be HIGH to perform any Write operation, and when LOW the device ignores write data bytes and goes to standby. |
| 2 | SCL | input | I2C interface clock input, with a maximum SCL frequency of 400 kHz. |
| 3 | SDA | bidirectional | Serial data I/O for the I2C interface. |
| 4 | GND | power_in | Ground reference for the device. |
| 5 | RW | passive | Wiper terminal of the digitally controlled potentiometer; voltage at this DCP pin must stay between VSS and VCC, and wiper current is limited to ±3.0 mA. |
| 6 | RL | passive | Low terminal of the digitally controlled potentiometer; voltage at this DCP pin must stay between VSS and VCC. |
| 7 | RH | passive | High terminal of the digitally controlled potentiometer; voltage at this DCP pin must stay between VSS and VCC. |
| 8 | VCC | power_in | Power supply, 2.7 V to 5.5 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | RENESAS |
| Package | MSOP-8 |
| Category | Data Converters |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| RH to RL Resistance Tolerance | -20 | 20 | % | 3 | |||
| Wiper Resistance | RW | 70 | 200 | Ω | VCC = 3.3V at +25°C; wiper current = VCC/RTOTAL | 3 | |
| Integral Non-Linearity (voltage divider) | INL | -1 | 1 | LSB | Voltage divider mode (0V at RL; VCC at RH; measured at RW, unloaded) | 3 | |
| Differential Non-Linearity (voltage divider), U option | DNL | -0.5 | LSB | Monotonic over all tap positions | 3 | ||
| Zero-Scale Error, U option | ZSerror | 0 | 0.5 | 2 | LSB | 3 | |
| Full-Scale Error, U option | FSerror | -2 | -0.5 | 0 | LSB | 3 | |
| Ratiometric Temperature Coefficient | TCV | -4 | 4 | ppm/°C | DCP Register set to 80 hex | 3 | |
| Resistor Mode Integral Non-Linearity | RINL | -1 | 1 | MI | DCP register set between 20 hex and FF hex. Monotonic over all tap positions | 3 | |
| Resistor Mode Differential Non-Linearity, U option | RDNL | -0.5 | MI | DCP register set between 20 hex and FF hex. Monotonic over all tap positions | 3 | ||
| Offset, U option | Roffset | 0 | 0.5 | 2 | MI | 3 | |
| Resistance Temperature Coefficient | TCR | -165 | 165 | ppm/°C | DCP register set between 20 hex and FF hex | 3 | |
| DCP Leakage Current | ILkgDCP | 0.1 | 1 | µA | Voltage at pin from GND to VCC | 3 | |
| VCC Supply Current (Volatile write/read) | ICC1 | 1 | mA | fSCL = 400kHz; SDA = Open; (for I2C, Active, Read and Volatile Write States only) | 4 | ||
| VCC Supply Current (Nonvolatile Write) | ICC2 | 3 | mA | fSCL = 400kHz; SDA = Open; (for I2C, Active, Nonvolatile Write State only) | 4 | ||
| VCC Current (Standby) | ISB | 5 | µA | VCC = +5.5V, I2C Interface in Standby State | 4 | ||
| VCC Current (Standby) | ISB | 2 | µA | VCC = +3.6V, I2C Interface in Standby State | 4 | ||
| Leakage Current, at Pins SDA, SCL, and WP | ILkgDig | -10 | 10 | µA | Voltage at pin from GND to VCC | 4 | |
| DCP Wiper Response Time | tDCP | 1 | µs | SCL falling edge of last bit of DCP Data Byte to wiper change | 4 | ||
| Power-On Recall Voltage | Vpor | 1.8 | 2.6 | V | Minimum VCC at which memory recall occurs | 4 | |
| VCC Ramp Rate | VCCRamp | 0.2 | V/ms | 4 | |||
| Power-Up Delay | tD | 3 | ms | VCC above Vpor, to DCP Initial Value Register recall completed, and I2C Interface in standby state | 4 | ||
| Input Buffer LOW Voltage (WP, SDA, SCL) | VIL | -0.3 | V | 4 | |||
| SDA Output Buffer LOW Voltage | VOL | 0 | 0.4 | V | Sinking 4mA | 4 | |
| SCL Frequency | fSCL | 400 | kHz | 4 | |||
| Pulse Width Suppression Time at SDA and SCL Inputs | tIN | 50 | ns | Any pulse narrower than the max spec is suppressed | 4 | ||
| SCL Falling Edge to SDA Output Data Valid | tAA | 900 | ns | SCL falling edge crossing 30% of VCC, until SDA exits the 30% to 70% of VCC window | 4 | ||
| Time the Bus Must be Free Before a New Transmission | tBUF | 1300 | ns | SDA crossing 70% of VCC during a STOP condition, to SDA crossing 70% of VCC during the following START condition | 4 | ||
| Clock LOW Time | tLOW | 1300 | ns | Measured at the 30% of VCC crossing | 4 | ||
| Clock HIGH Time | tHIGH | 600 | ns | Measured at the 70% of VCC crossing | 4 | ||
| START Condition Setup Time | tSU:STA | 600 | ns | SCL rising edge to SDA falling edge. Both crossing 70% of VCC | 4 | ||
| START Condition Hold Time | tHD:STA | 600 | ns | From SDA falling edge crossing 30% of VCC to SCL falling edge crossing 70% of VCC | 4 | ||
| Input Data Setup Time | tSU:DAT | 100 | ns | From SDA exiting the 30% to 70% of VCC window, to SCL rising edge crossing 30% of VCC | 4 | ||
| Input Data Hold Time | tHD:DAT | 0 | ns | From SCL rising edge crossing 70% of VCC to SDA entering the 30% to 70% of VCC window | 4 | ||
| STOP Condition Setup Time | tSU:STO | 600 | ns | From SCL rising edge crossing 70% of VCC, to SDA rising edge crossing 30% of VCC | 4 | ||
| STOP Condition Hold Time for Read, or Volatile Only Write | tHD:STO | 600 | ns | From SDA rising edge to SCL falling edge. Both crossing 70% of VCC | 4 | ||
| STOP Condition Hold Time for Non-Volatile Write | tHD:STO:NV | 2 | µs | From SDA rising edge to SCL falling edge. Both crossing 70% of VCC | 4 | ||
| Output Data Hold Time | tDH | 0 | ns | From SCL falling edge crossing 30% of VCC, until SDA enters the 30% to 70% of VCC window | 5 | ||
| SDA and SCL Rise Time | tR | 250 | ns | From 30% to 70% of VCC | 5 | ||
| SDA and SCL Fall Time | tF | 250 | ns | From 70% to 30% of VCC | 5 | ||
| Capacitive Loading of SDA or SCL | Cb | 10 | 400 | pF | Total on-chip and off-chip | 5 | |
| SDA and SCL Bus Pull-Up Resistor Off-Chip | Rpu | 1 | kΩ | Maximum is determined by tR and tF | 5 | ||
| Non-Volatile Write Cycle Time | tWP | 12 | 20 | ms | 5 | ||
| WP Setup Time | tSU:WP | 600 | ns | Before START condition | 5 | ||
| WP Hold Time | tHD:WP | 600 | ns | After STOP condition | 5 | ||
| Storage Temperature | -65 | 150 | °C | 3 | |||
| VCC Absolute Maximum | VCC | -0.3 | 6 | V | 3 | ||
| Voltage at Any Digital Interface Pin | -0.3 | V | With respect to VSS; upper limit printed as VCC+0.3 | 3 | |||
| Voltage at Any DCP Pin | -0.3 | V | With respect to VSS; upper limit printed as VCC | 3 | |||
| Wiper Current (10s, absolute maximum) | IW | -6 | 6 | mA | 10s | 3 | |
| Lead Temperature (Soldering) | 300 | °C | Soldering, 10s | 3 | |||
| Industrial Operating Temperature | -40 | 85 | °C | Industrial | 3 | ||
| VCC Supply Voltage | VCC | 2.7 | 5.5 | V | 3 | ||
| Power Rating of Each DCP | 5 | mW | 3 | ||||
| Wiper Current of Each DCP | -3 | 3 | mA | Printed as ±3.0 mA | 3 | ||
| Thermal Resistance Junction-to-Ambient, 8 Ld MSOP | θJA | 151 | °C/W | 8 Ld MSOP Package (Notes 6, 7) | 3 | ||
| Thermal Resistance Junction-to-Case, 8 Ld MSOP | θJC | 50 | °C/W | 8 Ld MSOP Package (Notes 6, 7) | 3 |
CAD (KiCad official)
- Symbol:
ISL95810UIU8Z-T - Footprint:
Package_SO:MSOP-8_3x3mm_P0.65mm - 3D model: MSOP-8 (KiCad packages3D, STEP)
- 3D model files:
isl95810uiu8z-t-etched.step/isl95810uiu8z-t-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);isl95810uiu8z-t.step/isl95810uiu8z-t.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: RENESAS datasheet (15 pp, sha256
0d23c3dc6b740eba, retrieved 2026-10-30, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).