main
History Download
Ray Publish 0.1.0 ea8b4a3

ISL9205DIRZ

RENESAS · Battery Management ICs · DFN-10(3x3)

ISL9205DIRZ from RENESAS, in a DFN-10(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VIN power_in Input power source to connect to a wall adapter; the recommended operating supply voltage is 4.25V to 6.5V.
2 FAULT output Open-drain output pulled LOW under any fault condition (which also resets the time counter) and high impedance when the charger is disabled.
3 STATUS output Open-drain output pulled LOW while charging a battery and high impedance once charge current drops to IMIN (latched until a recharge or new charge cycle) or when the charger is disabled.
4 TIME passive Connect a timing capacitor between this pin and GND to set the oscillation period, which also provides the charger time reference.
5 GND power_in Connection to system ground.
6 EN input Enable logic input with internal 400kΩ pull-up: LOW disables the charger, floating enables it.
7 V2P8 power_out 2.8V reference voltage output (2.8V to 3.0V, load under 1mA) that is present when VIN is above the POR threshold and zero otherwise, usable as an adapter-presence indication.
8 IREF passive Charge current programming and monitoring pin; a resistor to GND sets the Constant Current phase charge current as IREF = 80/RIREF (RIREF in kΩ).
9 TEMP input Input for an external NTC thermistor to GND, also used for battery removal detection.
10 VBAT power_in Connection to the battery; a ceramic capacitor of at least 1µF is needed for stability with no battery attached, or 0.1µF when a battery is attached.
11 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer RENESAS
Package DFN-10(3x3)
Category Power Management
Pins 11

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Rising POR Threshold VPOR 3.2 3.6 3.9 V VBAT = 3.0V, use V2P8 pin to indicate the comparator output. 6
Falling POR Threshold VPOR 2.25 2.5 2.7 V 6
VIN-BAT Offset Voltage Rising Edge VOS 45 80 100 mV VBAT = 4.2V, IBAT = 20mA, use STATUS pin to indicate the comparator output (Note 6) 6
BAT Pin Sink Current ISTANDBY 3.3 µA Charger disabled or the input is floating 6
VIN Pin Supply Current (disabled) IVIN 150 250 µA Charger disabled 6
Output Voltage VCH 4.185 4.2 4.215 V Tested at 50mA load, 5V input, and +25°C 6
Output Voltage over temperature VCH 4.175 4.2 4.225 V -40°C < TA < +85°C, 4.3V < VIN < 6.5V 6
Constant Charge Current ICC 760 800 840 mA RIREF = 100kΩ, VBAT = 3.0V to 4.0V 6
Trickle Charge Current ITRK 64 80 96 mA RIREF = 100kΩ, VBAT = 0V to 2.5V 6
End-of-Charge Current IMIN 70 80 90 mA RIREF = 100kΩ (ISL9205A, ISL9205B, ISL9205C and ISL9205D) 6
V2P8 Pin Output Voltage VV2P8 2.8 2.9 3 V Load current less than 1mA 6
Preconditioning Charge Threshold Voltage VMIN 2.7 2.8 2.9 V 7
Preconditioning Voltage Hysteresis VMINHYS 50 100 150 mV 7
Recharge Threshold VRCH -225 -150 -70 mV Referenced to the charger output voltage VCH 7
Temperature High Voltage Threshold 1.98 2 2.02 V V2P8 = 3.0V 7
Temperature Low Voltage Threshold 0.99 1 1.01 V V2P8 = 3.0V 7
Oscillation Period tOSC 2.7 3 3.3 ms CTIME = 15nF 7
EN Pin Logic Input High 1.3 V 7
EN Pin Logic Input Low 0.5 V 7
EN Pin Internal Pull-Up Resistance 200 400 600 kΩ 7
STATUS/FAULT Output Voltage when On 0.8 V 10mA current 7
STATUS/FAULT Leakage Current 1 µA VSTATUS = 6.5V 7
Operating Supply Voltage (VIN Pin) VIN 4.25 6.5 V 6
Ambient Temperature Range TA -40 85 °C 6
Programmed Charge Current 50 900 mA 6
Voltage Ratings for All Pins -0.3 7 V 6
Charge Current 1 A 6
ESD Rating Human Body Model 2 kV 6
ESD Rating Machine Model 200 V 6
Maximum Junction Temperature 150 °C Plastic Package 6
Storage Temperature Range -65 150 °C 6
Thermal Resistance Junction-Ambient θJA 48 °C/W 3x3 DFN Package (Note 4) 6
Thermal Resistance Junction-Case θJC 6 °C/W 3x3 DFN Package 6
VIN Pin Supply Current (enabled) IVIN 1 mA Charger enabled 6
PMOS ON-Resistance rDS(ON) 500 µΩ VBAT = 4.0V, charge current = 0.35A 6
Charge Current Foldback Threshold TFOLD 110 °C 7
Recharge Threshold Hysteresis VRCHHYS 50 mV 7

CAD (KiCad official)

  • Symbol: ISL9205DIRZ
  • Footprint: Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm
  • 3D model: DFN-10(3x3) (KiCad packages3D, STEP)
  • 3D model files: isl9205dirz-etched.step / isl9205dirz-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); isl9205dirz.step / isl9205dirz.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: RENESAS datasheet (17 pp, sha256 f33b012bbbf33395, retrieved 2026-10-31, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF