Made with KiCad 10.0 · needs KiCad 10.0 or later to open · KiCad file format 20260206
ISL9205DIRZ
RENESAS · Battery Management ICs · DFN-10(3x3)
ISL9205DIRZ from RENESAS, in a DFN-10(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Input power source to connect to a wall adapter; the recommended operating supply voltage is 4.25V to 6.5V. |
| 2 | FAULT | output | Open-drain output pulled LOW under any fault condition (which also resets the time counter) and high impedance when the charger is disabled. |
| 3 | STATUS | output | Open-drain output pulled LOW while charging a battery and high impedance once charge current drops to IMIN (latched until a recharge or new charge cycle) or when the charger is disabled. |
| 4 | TIME | passive | Connect a timing capacitor between this pin and GND to set the oscillation period, which also provides the charger time reference. |
| 5 | GND | power_in | Connection to system ground. |
| 6 | EN | input | Enable logic input with internal 400kΩ pull-up: LOW disables the charger, floating enables it. |
| 7 | V2P8 | power_out | 2.8V reference voltage output (2.8V to 3.0V, load under 1mA) that is present when VIN is above the POR threshold and zero otherwise, usable as an adapter-presence indication. |
| 8 | IREF | passive | Charge current programming and monitoring pin; a resistor to GND sets the Constant Current phase charge current as IREF = 80/RIREF (RIREF in kΩ). |
| 9 | TEMP | input | Input for an external NTC thermistor to GND, also used for battery removal detection. |
| 10 | VBAT | power_in | Connection to the battery; a ceramic capacitor of at least 1µF is needed for stability with no battery attached, or 0.1µF when a battery is attached. |
| 11 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | RENESAS |
| Package | DFN-10(3x3) |
| Category | Power Management |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Rising POR Threshold | VPOR | 3.2 | 3.6 | 3.9 | V | VBAT = 3.0V, use V2P8 pin to indicate the comparator output. | 6 |
| Falling POR Threshold | VPOR | 2.25 | 2.5 | 2.7 | V | 6 | |
| VIN-BAT Offset Voltage Rising Edge | VOS | 45 | 80 | 100 | mV | VBAT = 4.2V, IBAT = 20mA, use STATUS pin to indicate the comparator output (Note 6) | 6 |
| BAT Pin Sink Current | ISTANDBY | 3.3 | µA | Charger disabled or the input is floating | 6 | ||
| VIN Pin Supply Current (disabled) | IVIN | 150 | 250 | µA | Charger disabled | 6 | |
| Output Voltage | VCH | 4.185 | 4.2 | 4.215 | V | Tested at 50mA load, 5V input, and +25°C | 6 |
| Output Voltage over temperature | VCH | 4.175 | 4.2 | 4.225 | V | -40°C < TA < +85°C, 4.3V < VIN < 6.5V | 6 |
| Constant Charge Current | ICC | 760 | 800 | 840 | mA | RIREF = 100kΩ, VBAT = 3.0V to 4.0V | 6 |
| Trickle Charge Current | ITRK | 64 | 80 | 96 | mA | RIREF = 100kΩ, VBAT = 0V to 2.5V | 6 |
| End-of-Charge Current | IMIN | 70 | 80 | 90 | mA | RIREF = 100kΩ (ISL9205A, ISL9205B, ISL9205C and ISL9205D) | 6 |
| V2P8 Pin Output Voltage | VV2P8 | 2.8 | 2.9 | 3 | V | Load current less than 1mA | 6 |
| Preconditioning Charge Threshold Voltage | VMIN | 2.7 | 2.8 | 2.9 | V | 7 | |
| Preconditioning Voltage Hysteresis | VMINHYS | 50 | 100 | 150 | mV | 7 | |
| Recharge Threshold | VRCH | -225 | -150 | -70 | mV | Referenced to the charger output voltage VCH | 7 |
| Temperature High Voltage Threshold | 1.98 | 2 | 2.02 | V | V2P8 = 3.0V | 7 | |
| Temperature Low Voltage Threshold | 0.99 | 1 | 1.01 | V | V2P8 = 3.0V | 7 | |
| Oscillation Period | tOSC | 2.7 | 3 | 3.3 | ms | CTIME = 15nF | 7 |
| EN Pin Logic Input High | 1.3 | V | 7 | ||||
| EN Pin Logic Input Low | 0.5 | V | 7 | ||||
| EN Pin Internal Pull-Up Resistance | 200 | 400 | 600 | kΩ | 7 | ||
| STATUS/FAULT Output Voltage when On | 0.8 | V | 10mA current | 7 | |||
| STATUS/FAULT Leakage Current | 1 | µA | VSTATUS = 6.5V | 7 | |||
| Operating Supply Voltage (VIN Pin) | VIN | 4.25 | 6.5 | V | 6 | ||
| Ambient Temperature Range | TA | -40 | 85 | °C | 6 | ||
| Programmed Charge Current | 50 | 900 | mA | 6 | |||
| Voltage Ratings for All Pins | -0.3 | 7 | V | 6 | |||
| Charge Current | 1 | A | 6 | ||||
| ESD Rating Human Body Model | 2 | kV | 6 | ||||
| ESD Rating Machine Model | 200 | V | 6 | ||||
| Maximum Junction Temperature | 150 | °C | Plastic Package | 6 | |||
| Storage Temperature Range | -65 | 150 | °C | 6 | |||
| Thermal Resistance Junction-Ambient | θJA | 48 | °C/W | 3x3 DFN Package (Note 4) | 6 | ||
| Thermal Resistance Junction-Case | θJC | 6 | °C/W | 3x3 DFN Package | 6 | ||
| VIN Pin Supply Current (enabled) | IVIN | 1 | mA | Charger enabled | 6 | ||
| PMOS ON-Resistance | rDS(ON) | 500 | µΩ | VBAT = 4.0V, charge current = 0.35A | 6 | ||
| Charge Current Foldback Threshold | TFOLD | 110 | °C | 7 | |||
| Recharge Threshold Hysteresis | VRCHHYS | 50 | mV | 7 |
CAD (KiCad official)
- Symbol:
ISL9205DIRZ - Footprint:
Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm - 3D model: DFN-10(3x3) (KiCad packages3D, STEP)
- 3D model files:
isl9205dirz-etched.step/isl9205dirz-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);isl9205dirz.step/isl9205dirz.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: RENESAS datasheet (17 pp, sha256
f33b012bbbf33395, retrieved 2026-10-31, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).