main
Ray
Publish 0.1.1
d6b5d80
ISL81805FRTZ-T
RENESAS · DC-DC Converters · TQFN-32(5x5)
ISL81805FRTZ-T from RENESAS, in a TQFN-32(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | COMP1 | output | Channel 1 voltage error GM amplifier output that sets the inner current-loop reference, and the PWM duty cycle reduces to 0% when the pin is pulled below 1V. |
| 2 | SS/TRK1 | passive | Channel 1 soft-start or track pin, where a regulated 2µA source charges the soft-start capacitor to set the output ramp, or an external master rail is applied through a resistor divider for tracking. |
| 3 | VCC5V | power_out | Output of the internal 5V linear regulator that biases the IC, which must be decoupled to SGND with a minimum 4.7µF ceramic capacitor placed close to the pin. |
| 4 | NC | unconnected | No connection pin. |
| 5 | RT/SYNC | input | A resistor to ground sets the default switching frequency from 100kHz to 1MHz, where an open or VCC5V connection gives 120kHz, GND gives 575kHz, and an applied external clock synchronizes the internal oscillator. |
| 6 | PLL_COMP | passive | Compensation pin for the internal PLL, where RPLL 2.7kΩ, CPLL1 10nF and CPLL2 820pF are recommended. |
| 7 | CLKOUT/DITHER | bidirectional | Dual-function pin that outputs a clock to synchronize other ISL81805 devices when no capacitor is connected, or enables frequency dither of about ±15% when a capacitor is connected. |
| 8 | SS/TRK2/OV | bidirectional | Channel 2 soft-start or track pin with a regulated 2µA charge current, which carries the OVP trip signal instead in dual-phase operation. |
| 9 | COMP2/CLKEN | bidirectional | Channel 2 voltage error GM amplifier output where the PWM duty cycle reduces to 0% when the pin is pulled below 1.1V, and in dual-phase use it carries the PFM OFF (CLKEN) signal. |
| 10 | FB2/BSTEN | bidirectional | Channel 2 output voltage feedback input regulated to the internal 0.8V reference, which carries the Burst enable (BSTEN) signal in dual-phase operation. |
| 11 | IMON2 | passive | Channel 2 input current monitor whose pin voltage reaches 1.2V for the average current limit, and a voltage above 3V selects single-output dual-phase mode. |
| 12 | EN/UVLO2 | input | Channel 2 enable and accurate UVLO input that disables the channel when grounded, activates the LDOs above 1.3V and the PWM modulator above 1.8V, is internally pulled up when floating, and has a Zener sink limit of 100µA. |
| 13 | CS2- | input | Channel 2 output current-sense signal negative input pin. |
| 14 | CS2+ | input | Channel 2 output current-sense signal positive input pin. |
| 15 | PGOOD | output | Open-drain power-good output that is pulled low when the Channel 1 output is not within ±11% of nominal or EN1 is pulled low. |
| 16 | UG2 | output | High-side MOSFET gate driver output for Channel 2, controlled by the Channel 2 PWM signal. |
| 17 | PHASE2 | passive | Phase node of the Channel 2 boost converter, connected to the upper MOSFET source, filter inductor and lower MOSFET drain. |
| 18 | BOOT2 | passive | Bootstrap pin for the Channel 2 high-side driver, with a bootstrap diode from VDD and a minimum on-time refresh issued when BOOT2 to PHASE2 drops to 5.9V at no switching. |
| 19 | LG2/OC_MODE | passive | Channel 2 low-side gate driver output and OCP mode select pin, where a resistor to ground sets constant-current OCP below 0.3V or hiccup OCP above 0.3V during initialization. |
| 20 | VDD | power_out | Output of the internal 8V linear regulator supplied by VIN or EXTBIAS that powers the low-side drivers and high-side boot circuits, and must be decoupled to PGND with a minimum 4.7µF ceramic capacitor. |
| 21 | PGND | power_in | Power ground connection that is tied to the sources of the lower MOSFETs and the negative terminals of the external input capacitors. |
| 22 | LG1/PWM_MODE | passive | Channel 1 low-side gate driver output and PWM mode select pin, where a resistor to ground selects Forced PWM below 0.3V or Diode Emulation Burst mode above 0.3V during initialization. |
| 23 | BOOT1 | passive | Bootstrap pin for the Channel 1 high-side driver, with a bootstrap diode from VDD and a minimum on-time refresh issued when BOOT1 to PHASE1 drops to 5.9V at no switching. |
| 24 | PHASE1 | passive | Phase node of the Channel 1 boost converter, connected to the upper MOSFET source, filter inductor and lower MOSFET drain. |
| 25 | UG1 | output | High-side MOSFET gate driver output for Channel 1, controlled by the Channel 1 PWM signal. |
| 26 | EXTBIAS | power_in | External bias input for the optional VDD LDO, which disconnects the VIN LDO above 7.4V and must be decoupled with 10µF when used, otherwise tied to ground and never left floating. |
| 27 | VIN | power_in | Input rail that powers the internal VDD LDO and should be decoupled to ground with a 0.1µF to 1µF ceramic capacitor, with an operating range of 4.5V to 80V. |
| 28 | CS1+ | input | Channel 1 output current-sense signal positive input pin. |
| 29 | CS1- | input | Channel 1 output current-sense signal negative input pin. |
| 30 | EN/UVLO1 | input | Channel 1 enable and accurate UVLO input that disables the channel when grounded, activates the LDOs above 1.3V and the PWM modulator above 1.8V, is internally pulled up when floating, and has a Zener sink limit of 100µA. |
| 31 | IMON1 | passive | Channel 1 input current monitor whose pin voltage reaches 1.2V for the average current limit, with a Burst mode entry threshold near 815mV. |
| 32 | FB1 | input | Channel 1 output voltage feedback input regulated to the internal 0.8V reference, which also serves Channel 2 feedback in dual-phase operation. |
| 33 | EPAD/SGND | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | RENESAS |
| Package | TQFN-32(5x5) |
| Category | Power Management (PMIC) |
| Pins | 33 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VCC5V, EN/UVLO1, EN/UVLO2 to GND | -0.3 | 5.9 | V | 13 | |||
| VDD to GND | -0.3 | 9 | V | 13 | |||
| EXTBIAS to GND | -0.3 | 40 | V | 13 | |||
| VIN to GND | VIN | -0.3 | 85 | V | 13 | ||
| CS1+, CS1-, CS2+, CS2- to GND | -0.3 | 85 | V | 13 | |||
| BOOT1, 2 / UG1, 2 to PHASE1, 2 | -0.3 | 12 | V | 13 | |||
| PHASE1, 2 to GND | -5 | 85 | V | min -5 V for <20ns; -0.3 V DC | 13 | ||
| FB1, FB2, SS/TRK1, SS/TRK2, COMP1, COMP2, RT/SYNC, PLL_COMP, CLKOUT/DITHER, BSTEN, CLKEN, OV, PGOOD, IMON1, IMON2 to GND | -0.3 | V | maximum printed as VCC5V + 0.3 V | 13 | |||
| LG1/PWM_MODE, LG2/OC_MODE to GND | -0.3 | V | maximum printed as VDD + 0.3 V | 13 | |||
| CS1+ to CS1- and CS2+ to CS2- | -0.3 | 0.3 | V | 13 | |||
| VCC5V, VDD short-circuit to GND duration | 1 | s | short-circuit duration | 13 | |||
| Junction Temperature | TJ | -55 | 150 | °C | 13 | ||
| Storage Temperature Range | -65 | 150 | °C | 13 | |||
| Temperature | -40 | 125 | °C | 14 | |||
| VIN to GND | VIN | 4.5 | 80 | V | 14 | ||
| VCC5V, EN/UVLO1, EN/UVLO2 to GND | 0 | 5.4 | V | 14 | |||
| VDD to GND | 0 | 8.4 | V | 14 | |||
| EXTBIAS to GND | 0 | 36 | V | 14 | |||
| Input Voltage Range | VIN | 4.5 | 80 | V | 14 | ||
| Internal LDO Output Voltage (VCC5V) | VCC5V | 4.7 | 5 | 5.4 | V | VIN = 8V, IL = 0mA | 14 |
| Maximum Supply Current of Internal LDO (VCC5V) | IVCC_MAX | 120 | mA | VVCC5V = 0V, VIN = 8V | 14 | ||
| Internal LDO Output Voltage (VDD) | VDD | 7.5 | 8 | 8.4 | V | VIN = 12V, EXTBIAS = 0V, IL = 0mA | 14 |
| Maximum Supply Current of Internal LDO (VDD) | IVDD_MAX | 120 | mA | VVDD = 0V, EXTBIAS = 0V, VIN = 12V | 14 | ||
| EXTBIAS Switch Over Threshold Voltage, Rising | VEXT_THR | 7.1 | 7.38 | 7.55 | V | EXTBIAS voltage | 15 |
| EXTBIAS Switch Over Threshold Voltage, Falling | VEXT_THF | 6.6 | 6.85 | 7.1 | V | EXTBIAS voltage | 15 |
| VCC5V Rising POR Threshold | VPORTHR | 3.7 | 4 | 4.3 | V | VCC5V voltage, 0mA on VCC5V and VDD | 15 |
| VCC5V Falling POR Threshold | VPORTHF | 3.3 | 3.55 | 3.75 | V | VCC5V voltage, 0mA on VCC5V and VDD | 15 |
| EN1 Rise Threshold | VEN1SS_THR | 0.75 | 1.05 | 1.3 | V | VIN > 5.6V | 15 |
| EN1 Fall Threshold | VEN1SS_THF | 0.6 | 0.9 | 1.1 | V | VIN > 5.6V | 15 |
| EN1 Hysteresis | VEN1SS_HYST | 70 | 150 | 300 | mV | VIN > 5.6V | 15 |
| UVLO1 Rise Threshold | VUVLO1_THR | 1.77 | 1.8 | 1.83 | V | VIN > 5.6V | 15 |
| EN2 Rise Threshold | VEN2SS_THR | 0.75 | 1.05 | 1.3 | V | VIN > 5.6V | 15 |
| EN2 Fall Threshold | VEN2SS_THF | 0.6 | 0.9 | 1.1 | V | VIN > 5.6V | 15 |
| EN2 Hysteresis | VEN2SS_HYST | 70 | 150 | 300 | mV | VIN > 5.6V | 15 |
| UVLO2 Rise Threshold | VUVLO2_THR | 1.77 | 1.8 | 1.83 | V | VIN > 5.6V | 15 |
| PGOOD Upper Threshold | VPGOV | 107 | 109 | 112 | % | 15 | |
| PGOOD Lower Threshold | VPGUV | 87 | 90 | 92 | % | 15 | |
| FB_1 Pin Bias Current | IFBOUTLKG1 | -50 | 0 | 50 | nA | 16 | |
| FB_2 Pin Bias Current | IFBOUTLKG2 | -50 | 0 | 50 | nA | 16 | |
| COMP1 Max High Voltage | VCOMP1_HIGH | 4.7 | V | FB1 = 0V | 16 | ||
| COMP2 Max High Voltage | VCOMP2_HIGH | 4.7 | V | FB2 = 0V | 16 | ||
| Internal Voltage Loop Reference Voltage Accuracy | -0.75 | 0.75 | % | TA = 0°C to +85°C | 16 | ||
| Internal Voltage Loop Reference Voltage Accuracy | -1 | 1 | % | TA = -40°C to +125°C | 16 | ||
| PWM1 Minimum Off-Time | tOFF_MIN1 | 220 | ns | 17 | |||
| PWM1 Minimum On-Time | tON_MIN1 | 100 | ns | 17 | |||
| PWM1 Ramp Offset | VROFFSET1 | 0.85 | 1.1 | 1.25 | V | 17 | |
| Current Sense1 Differential Voltage Range | VCS1+ - VCS1- | -80 | 150 | mV | 17 | ||
| Current Sense1 Common-Mode Voltage Range | CMIRCS1 | 0 | 80 | V | 17 | ||
| Switching Frequency (RT = 144kΩ) | fSW | 220 | 245 | 265 | kHz | RT = 144kΩ | 18 |
| Switching Frequency (RT = 72kΩ) | fSW | 420 | 450 | 485 | kHz | RT = 72kΩ | 18 |
| Switching Frequency (RT open or to VCC5V) | fSW | 90 | 120 | 145 | kHz | RT open or to VCC5V | 18 |
| Switching Frequency (RT = 0V) | fSW | 470 | 575 | 650 | kHz | RT = 0V | 18 |
| SYNC Synchronization Range | fSYNC | 140 | 1000 | kHz | 18 | ||
| PWM1 Burst Mode Enter Threshold | VIMON1BSTEN | 0.77 | 0.815 | 0.85 | V | IMON1 pin voltage | 18 |
| Driver 1, 2 BOOT Refresh Trip Voltage | VBOOTRF1,2 | 3.8 | 4.6 | 5.5 | V | BOOT voltage - PHASE voltage | 18 |
| Thermal Resistance, Junction-to-Ambient (32 Ld TQFN) | θJA | 29 | °C/W | free air, high-effective thermal conductivity test board | 13 | ||
| Thermal Resistance, Junction-to-Case (32 Ld TQFN) | θJC | 1 | °C/W | case = center of exposed metal pad | 13 |
CAD (KiCad official)
- Symbol:
ISL81805FRTZ-T - Footprint:
Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm - 3D model: TQFN-32(5x5) (KiCad packages3D, STEP)
- 3D model files:
isl81805frtz-t-etched.step/isl81805frtz-t-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);isl81805frtz-t.step/isl81805frtz-t.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: RENESAS datasheet (45 pp, sha256
388d19052b6c5c32, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# ISL81805FRTZ-T
**RENESAS** · DC-DC Converters · TQFN-32(5x5)
ISL81805FRTZ-T from RENESAS, in a TQFN-32(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | COMP1 | output | Channel 1 voltage error GM amplifier output that sets the inner current-loop reference, and the PWM duty cycle reduces to 0% when the pin is pulled below 1V. |
| 2 | SS/TRK1 | passive | Channel 1 soft-start or track pin, where a regulated 2µA source charges the soft-start capacitor to set the output ramp, or an external master rail is applied through a resistor divider for tracking. |
| 3 | VCC5V | power_out | Output of the internal 5V linear regulator that biases the IC, which must be decoupled to SGND with a minimum 4.7µF ceramic capacitor placed close to the pin. |
| 4 | NC | unconnected | No connection pin. |
| 5 | RT/SYNC | input | A resistor to ground sets the default switching frequency from 100kHz to 1MHz, where an open or VCC5V connection gives 120kHz, GND gives 575kHz, and an applied external clock synchronizes the internal oscillator. |
| 6 | PLL_COMP | passive | Compensation pin for the internal PLL, where RPLL 2.7kΩ, CPLL1 10nF and CPLL2 820pF are recommended. |
| 7 | CLKOUT/DITHER | bidirectional | Dual-function pin that outputs a clock to synchronize other ISL81805 devices when no capacitor is connected, or enables frequency dither of about ±15% when a capacitor is connected. |
| 8 | SS/TRK2/OV | bidirectional | Channel 2 soft-start or track pin with a regulated 2µA charge current, which carries the OVP trip signal instead in dual-phase operation. |
| 9 | COMP2/CLKEN | bidirectional | Channel 2 voltage error GM amplifier output where the PWM duty cycle reduces to 0% when the pin is pulled below 1.1V, and in dual-phase use it carries the PFM OFF (CLKEN) signal. |
| 10 | FB2/BSTEN | bidirectional | Channel 2 output voltage feedback input regulated to the internal 0.8V reference, which carries the Burst enable (BSTEN) signal in dual-phase operation. |
| 11 | IMON2 | passive | Channel 2 input current monitor whose pin voltage reaches 1.2V for the average current limit, and a voltage above 3V selects single-output dual-phase mode. |
| 12 | EN/UVLO2 | input | Channel 2 enable and accurate UVLO input that disables the channel when grounded, activates the LDOs above 1.3V and the PWM modulator above 1.8V, is internally pulled up when floating, and has a Zener sink limit of 100µA. |
| 13 | CS2- | input | Channel 2 output current-sense signal negative input pin. |
| 14 | CS2+ | input | Channel 2 output current-sense signal positive input pin. |
| 15 | PGOOD | output | Open-drain power-good output that is pulled low when the Channel 1 output is not within ±11% of nominal or EN1 is pulled low. |
| 16 | UG2 | output | High-side MOSFET gate driver output for Channel 2, controlled by the Channel 2 PWM signal. |
| 17 | PHASE2 | passive | Phase node of the Channel 2 boost converter, connected to the upper MOSFET source, filter inductor and lower MOSFET drain. |
| 18 | BOOT2 | passive | Bootstrap pin for the Channel 2 high-side driver, with a bootstrap diode from VDD and a minimum on-time refresh issued when BOOT2 to PHASE2 drops to 5.9V at no switching. |
| 19 | LG2/OC_MODE | passive | Channel 2 low-side gate driver output and OCP mode select pin, where a resistor to ground sets constant-current OCP below 0.3V or hiccup OCP above 0.3V during initialization. |
| 20 | VDD | power_out | Output of the internal 8V linear regulator supplied by VIN or EXTBIAS that powers the low-side drivers and high-side boot circuits, and must be decoupled to PGND with a minimum 4.7µF ceramic capacitor. |
| 21 | PGND | power_in | Power ground connection that is tied to the sources of the lower MOSFETs and the negative terminals of the external input capacitors. |
| 22 | LG1/PWM_MODE | passive | Channel 1 low-side gate driver output and PWM mode select pin, where a resistor to ground selects Forced PWM below 0.3V or Diode Emulation Burst mode above 0.3V during initialization. |
| 23 | BOOT1 | passive | Bootstrap pin for the Channel 1 high-side driver, with a bootstrap diode from VDD and a minimum on-time refresh issued when BOOT1 to PHASE1 drops to 5.9V at no switching. |
| 24 | PHASE1 | passive | Phase node of the Channel 1 boost converter, connected to the upper MOSFET source, filter inductor and lower MOSFET drain. |
| 25 | UG1 | output | High-side MOSFET gate driver output for Channel 1, controlled by the Channel 1 PWM signal. |
| 26 | EXTBIAS | power_in | External bias input for the optional VDD LDO, which disconnects the VIN LDO above 7.4V and must be decoupled with 10µF when used, otherwise tied to ground and never left floating. |
| 27 | VIN | power_in | Input rail that powers the internal VDD LDO and should be decoupled to ground with a 0.1µF to 1µF ceramic capacitor, with an operating range of 4.5V to 80V. |
| 28 | CS1+ | input | Channel 1 output current-sense signal positive input pin. |
| 29 | CS1- | input | Channel 1 output current-sense signal negative input pin. |
| 30 | EN/UVLO1 | input | Channel 1 enable and accurate UVLO input that disables the channel when grounded, activates the LDOs above 1.3V and the PWM modulator above 1.8V, is internally pulled up when floating, and has a Zener sink limit of 100µA. |
| 31 | IMON1 | passive | Channel 1 input current monitor whose pin voltage reaches 1.2V for the average current limit, with a Burst mode entry threshold near 815mV. |
| 32 | FB1 | input | Channel 1 output voltage feedback input regulated to the internal 0.8V reference, which also serves Channel 2 feedback in dual-phase operation. |
| 33 | EPAD/SGND | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | RENESAS |
| Package | TQFN-32(5x5) |
| Category | Power Management (PMIC) |
| Pins | 33 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VCC5V, EN/UVLO1, EN/UVLO2 to GND | | -0.3 | | 5.9 | V | | 13 |
| VDD to GND | | -0.3 | | 9 | V | | 13 |
| EXTBIAS to GND | | -0.3 | | 40 | V | | 13 |
| VIN to GND | VIN | -0.3 | | 85 | V | | 13 |
| CS1+, CS1-, CS2+, CS2- to GND | | -0.3 | | 85 | V | | 13 |
| BOOT1, 2 / UG1, 2 to PHASE1, 2 | | -0.3 | | 12 | V | | 13 |
| PHASE1, 2 to GND | | -5 | | 85 | V | min -5 V for <20ns; -0.3 V DC | 13 |
| FB1, FB2, SS/TRK1, SS/TRK2, COMP1, COMP2, RT/SYNC, PLL_COMP, CLKOUT/DITHER, BSTEN, CLKEN, OV, PGOOD, IMON1, IMON2 to GND | | -0.3 | | | V | maximum printed as VCC5V + 0.3 V | 13 |
| LG1/PWM_MODE, LG2/OC_MODE to GND | | -0.3 | | | V | maximum printed as VDD + 0.3 V | 13 |
| CS1+ to CS1- and CS2+ to CS2- | | -0.3 | | 0.3 | V | | 13 |
| VCC5V, VDD short-circuit to GND duration | | | | 1 | s | short-circuit duration | 13 |
| Junction Temperature | TJ | -55 | | 150 | °C | | 13 |
| Storage Temperature Range | | -65 | | 150 | °C | | 13 |
| Temperature | | -40 | | 125 | °C | | 14 |
| VIN to GND | VIN | 4.5 | | 80 | V | | 14 |
| VCC5V, EN/UVLO1, EN/UVLO2 to GND | | 0 | | 5.4 | V | | 14 |
| VDD to GND | | 0 | | 8.4 | V | | 14 |
| EXTBIAS to GND | | 0 | | 36 | V | | 14 |
| Input Voltage Range | VIN | 4.5 | | 80 | V | | 14 |
| Internal LDO Output Voltage (VCC5V) | VCC5V | 4.7 | 5 | 5.4 | V | VIN = 8V, IL = 0mA | 14 |
| Maximum Supply Current of Internal LDO (VCC5V) | IVCC_MAX | | | 120 | mA | VVCC5V = 0V, VIN = 8V | 14 |
| Internal LDO Output Voltage (VDD) | VDD | 7.5 | 8 | 8.4 | V | VIN = 12V, EXTBIAS = 0V, IL = 0mA | 14 |
| Maximum Supply Current of Internal LDO (VDD) | IVDD_MAX | | | 120 | mA | VVDD = 0V, EXTBIAS = 0V, VIN = 12V | 14 |
| EXTBIAS Switch Over Threshold Voltage, Rising | VEXT_THR | 7.1 | 7.38 | 7.55 | V | EXTBIAS voltage | 15 |
| EXTBIAS Switch Over Threshold Voltage, Falling | VEXT_THF | 6.6 | 6.85 | 7.1 | V | EXTBIAS voltage | 15 |
| VCC5V Rising POR Threshold | VPORTHR | 3.7 | 4 | 4.3 | V | VCC5V voltage, 0mA on VCC5V and VDD | 15 |
| VCC5V Falling POR Threshold | VPORTHF | 3.3 | 3.55 | 3.75 | V | VCC5V voltage, 0mA on VCC5V and VDD | 15 |
| EN1 Rise Threshold | VEN1SS_THR | 0.75 | 1.05 | 1.3 | V | VIN > 5.6V | 15 |
| EN1 Fall Threshold | VEN1SS_THF | 0.6 | 0.9 | 1.1 | V | VIN > 5.6V | 15 |
| EN1 Hysteresis | VEN1SS_HYST | 70 | 150 | 300 | mV | VIN > 5.6V | 15 |
| UVLO1 Rise Threshold | VUVLO1_THR | 1.77 | 1.8 | 1.83 | V | VIN > 5.6V | 15 |
| EN2 Rise Threshold | VEN2SS_THR | 0.75 | 1.05 | 1.3 | V | VIN > 5.6V | 15 |
| EN2 Fall Threshold | VEN2SS_THF | 0.6 | 0.9 | 1.1 | V | VIN > 5.6V | 15 |
| EN2 Hysteresis | VEN2SS_HYST | 70 | 150 | 300 | mV | VIN > 5.6V | 15 |
| UVLO2 Rise Threshold | VUVLO2_THR | 1.77 | 1.8 | 1.83 | V | VIN > 5.6V | 15 |
| PGOOD Upper Threshold | VPGOV | 107 | 109 | 112 | % | | 15 |
| PGOOD Lower Threshold | VPGUV | 87 | 90 | 92 | % | | 15 |
| FB_1 Pin Bias Current | IFBOUTLKG1 | -50 | 0 | 50 | nA | | 16 |
| FB_2 Pin Bias Current | IFBOUTLKG2 | -50 | 0 | 50 | nA | | 16 |
| COMP1 Max High Voltage | VCOMP1_HIGH | | | 4.7 | V | FB1 = 0V | 16 |
| COMP2 Max High Voltage | VCOMP2_HIGH | | | 4.7 | V | FB2 = 0V | 16 |
| Internal Voltage Loop Reference Voltage Accuracy | | -0.75 | | 0.75 | % | TA = 0°C to +85°C | 16 |
| Internal Voltage Loop Reference Voltage Accuracy | | -1 | | 1 | % | TA = -40°C to +125°C | 16 |
| PWM1 Minimum Off-Time | tOFF_MIN1 | 220 | | | ns | | 17 |
| PWM1 Minimum On-Time | tON_MIN1 | 100 | | | ns | | 17 |
| PWM1 Ramp Offset | VROFFSET1 | 0.85 | 1.1 | 1.25 | V | | 17 |
| Current Sense1 Differential Voltage Range | VCS1+ - VCS1- | -80 | | 150 | mV | | 17 |
| Current Sense1 Common-Mode Voltage Range | CMIRCS1 | 0 | | 80 | V | | 17 |
| Switching Frequency (RT = 144kΩ) | fSW | 220 | 245 | 265 | kHz | RT = 144kΩ | 18 |
| Switching Frequency (RT = 72kΩ) | fSW | 420 | 450 | 485 | kHz | RT = 72kΩ | 18 |
| Switching Frequency (RT open or to VCC5V) | fSW | 90 | 120 | 145 | kHz | RT open or to VCC5V | 18 |
| Switching Frequency (RT = 0V) | fSW | 470 | 575 | 650 | kHz | RT = 0V | 18 |
| SYNC Synchronization Range | fSYNC | 140 | | 1000 | kHz | | 18 |
| PWM1 Burst Mode Enter Threshold | VIMON1BSTEN | 0.77 | 0.815 | 0.85 | V | IMON1 pin voltage | 18 |
| Driver 1, 2 BOOT Refresh Trip Voltage | VBOOTRF1,2 | 3.8 | 4.6 | 5.5 | V | BOOT voltage - PHASE voltage | 18 |
| Thermal Resistance, Junction-to-Ambient (32 Ld TQFN) | θJA | | 29 | | °C/W | free air, high-effective thermal conductivity test board | 13 |
| Thermal Resistance, Junction-to-Case (32 Ld TQFN) | θJC | | 1 | | °C/W | case = center of exposed metal pad | 13 |
## CAD (KiCad official)
- Symbol: `ISL81805FRTZ-T`
- Footprint: `Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm`
- 3D model: TQFN-32(5x5) (KiCad packages3D, STEP)
- 3D model files: `isl81805frtz-t-etched.step` / `isl81805frtz-t-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `isl81805frtz-t.step` / `isl81805frtz-t.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [RENESAS datasheet](docs/isl81805frtz-t-datasheet.pdf) (45 pp, sha256 `388d19052b6c5c32`, retrieved 2026-11-13, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/isl81805frtz-t-datasheet.pdf)