Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

ISL80112IRAJZ-T

RENESAS · Linear Voltage Regulators (LDO) · DFN-10(3x3)

ISL80112IRAJZ-T from RENESAS, in a DFN-10(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VOUT power_out Output voltage pin, adjustable over a range of 0.5V to 3.3V.
2 VOUT power_out Output voltage pin, adjustable over a range of 0.5V to 3.3V.
3 ADJ input ADJ pin for externally setting VOUT through a resistor divider, with absolute maximum rating of -0.3V to +6V relative to GND.
4 VBIAS power_in Bias voltage pin for internal control circuits, with a range of 2.9V to 5.5V.
5 GND power_in Ground pin.
6 PG output Power-good open-drain output that goes logic low when VOUT is not in regulation, with a rated sink current of 10mA.
7 ENABLE input VIN-independent chip enable, TTL and CMOS compatible, with a range of 0V to VBIAS that must never exceed the voltage applied to VBIAS.
8 NC unconnected No connect pin.
9 VIN power_in Input supply pin with a range of 0.7V to 3.6V.
10 VIN power_in Input supply pin with a range of 0.7V to 3.6V.
11 EPAD passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer RENESAS
Package DFN-10(3x3)
Category Power Supply Chip
Pins 11

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VIN Relative to GND VIN -0.3 6 V Relative to GND 4
VOUT Relative to GND VOUT -0.3 4 V Relative to GND 4
PG, ENABLE, ADJ Relative to GND -0.3 6 V Relative to GND (Note 5) 4
VBIAS Relative to GND VBIAS -0.3 6 V Relative to GND 4
PG Rated Current 10 mA 4
ESD Human Body Model 4000 V Tested per JESD22-A114E 4
ESD Machine Model 300 V Tested per JESD22-115-A 4
ESD Charged Device Model 2000 V 4
Latch-up 100 mA 4
Storage Temperature Range TSTG -65 150 °C 4
Junction Temperature Range TJ -40 125 °C 4
VIN Relative to GND (ISL80112) VIN 3.6 V Minimum is VOUT + 0.25V (ISL80112) 4
Nominal VOUT Range minimum VOUT 500 mV Nominal VOUT Range 4
Nominal VOUT Range maximum VOUT 3.3 V Nominal VOUT Range 4
PG, ENABLE, ADJ, SS Relative to GND 0 5.5 V Relative to GND 4
VBIAS Relative to GND VBIAS 0 5.5 V Relative to GND 4
VBIAS UVLO Rising UVLO_BIAS_r 2.3 2.9 V VBIAS Rising 4
VBIAS UVLO Falling UVLO_BIAS_f 1.55 2.1 2.8 V VBIAS Falling 4
DC ADJ Pin Voltage Accuracy VADJ 494 502 510 mV 0.7V VIN 3.6V, ILOAD 0A, 2.9V VBIAS 5.5V, VOUT = VADJ 4
DC Input Line Regulation -0.18 0.02 0.18 % 2.9V VIN 3.6V, VOUT = 2.5V 4
DC Bias Line Regulation -0.28 0.06 0.28 % 4.5V<VBIAS<5.5V, VOUT = 2.5V 4
DC Output Load Regulation -0.4 -0.04 0.4 % 0A ILOAD Full Load, VOUT = 2.5V 4
Feedback Input Current 10 80 nA VADJ = 0.5V 4
VIN Quiescent Current IQ (VIN) 8 10 mA VOUT = 2.5V 4
Ground Pin Current in Shutdown ISHDN 3 20 µA ENABLE Pin = 0.2V, TJ = +125°C 4
VIN Dropout Voltage (ISL80112) VDO(VIN) 53 115 mV ILOAD = 2A, VOUT = 2.5V, VBIAS = 4.5V (ISL80112) 4
VBIAS Dropout Voltage (ISL80112) VDO(BIAS) 1.2 1.4 V ILOAD = 2A, VOUT = 2.5V (ISL80112) 4
PG Flag Low Voltage 90 130 mV ISINK = 500µA 5
PG Flag Leakage Current 11 300 nA PG = 5V, VBIAS = 5.5V 5
PG Flag Sink Current 7 10 mA 6
Turn-on Threshold (Rising) 400 680 850 mV VIN = 3.6V, VBIAS = 5.5V 5
Enable Hysteresis 60 260 330 mV VIN = 3.6V, VBIAS = 5.5V 5
PG Flag Falling Threshold PGTH 71 82 93 %VOUT VBIAS = 5.5V 5
VIN Quiescent Current IQ (VIN) 10.6 mA VOUT = 3.3V, VIN = 3.6V, VBIAS = 5V 4
VIN Quiescent Current IQ (VIN) 3.5 mA VOUT = 1.0V, VIN = 1.4V, VBIAS = 3.3V 5
Output Short Circuit Current (2A Version) ISC 3.2 A VOUT = 0.2V (ISL80112) 5
PG Flag Hysteresis PGHYS 9.3 %VOUT VBIAS = 5.5V 5
Thermal Shutdown Temperature TSD 160 °C 5
Thermal Shutdown Hysteresis TSDn 20 °C 5
Input Supply Ripple Rejection PSRR(VIN) 80 dB f = 120Hz, ILOAD = 1A 5
Bias Supply Ripple Rejection PSRR(VBIAS) 60 dB f = 120Hz, ILOAD = 1A 5
Output Noise Voltage eN(RMS) 38 µVRMS BW = 100Hz f 100kHz, VBIAS = 2.9V, VIN = 1.6V, VOUT = 1.2V, ILOAD = 3A 5
Spectral Noise Density at 10Hz eN 3 µV/√Hz ILOAD = 3A, f = 10Hz, VBIAS = 2.9V, VIN = 1.6V, VOUT = 1.2V 5
Spectral Noise Density at 100Hz eN 1 µV/√Hz ILOAD = 3A, f = 100Hz, VBIAS = 2.9V, VIN = 1.6V, VOUT = 1.2V 5
EN Start-up Time tEN 50 µs COUT = 10µF, ILOAD = 1A 5
BIAS Start-up Time tBIAS 100 µs COUT = 10µF, EN = BIAS 5
Thermal Resistance Junction-to-Ambient θJA 48 °C/W 10 Ld 3x3 DFN, Notes 6, 7 4
Thermal Resistance Junction-to-Case θJC 4 °C/W 10 Ld 3x3 DFN 4
Thermal Resistance Junction-to-Board at Pin 3 θJB 14.7 °C/W at Pin 3 (Note 8) 4

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts copper 8. For θJB, the board temperature is taken on the board near the edge of the package, on a copper trace at either lead #3 or lead #5, as applicable. See 4

CAD (KiCad official)

  • Symbol: ISL80112IRAJZ-T
  • Footprint: Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm
  • 3D model: DFN-10(3x3) (KiCad packages3D, STEP)
  • 3D model files: isl80112irajz-t-etched.step / isl80112irajz-t-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); isl80112irajz-t.step / isl80112irajz-t.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: RENESAS datasheet (17 pp, sha256 d613b152e8e1b270, retrieved 2026-11-02, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF