main
History Download
Ray Publish 0.1.0 c93af09

ISL6721AARZ-T

RENESAS · DC-DC Controllers · QFN-16-EP(3x3)

ISL6721AARZ-T from RENESAS, in a QFN-16-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SYNC bidirectional Bidirectional synchronization signal that coordinates the switching frequency of multiple units; the first unit to assert it takes control, and the SYNC frequency can be higher or lower than the free-running oscillator frequency.
2 SLOPE passive Slope compensation pin where an internal current source charges an external capacitor to GND each switching cycle, and the resulting scaled ramp is added to the ISENSE signal.
3 UV input Undervoltage monitor input compared to an internal 1.93V reference to detect an undervoltage condition.
4 OV input Overvoltage monitor input compared to an internal 2.5V reference to detect an overvoltage condition.
5 RTCT passive Oscillator timing pin, with timing resistor RT connected from VREF and timing capacitor CT connected from this pin to LGND, giving a programmable frequency range of 100kHz to 1.0MHz.
6 ISET input Sets the pulse-by-pulse overcurrent threshold when a DC voltage between 0.35V and 1.2V is applied to this input.
7 FB input Feedback voltage input connected to the inverting input of the error amplifier, and current sense leading edge blanking is disabled when FB is below 2.0V.
8 COMP passive Error amplifier output and PWM comparator input, with the loop frequency compensation network connected between COMP and FB, and soft-start implemented as a clamp on the maximum COMP voltage.
9 SS passive Soft-start capacitor connection to LGND that sets the soft-start duration and the overcurrent shutdown delay.
10 LGND power_in Small-signal reference ground for all analog functions on the device, to be connected externally to PGND with a short PCB trace close to the IC.
11 VREF power_out 5V reference voltage output that should be bypassed to LGND with a 0.01µF or larger capacitor, since smaller capacitance may cause unstable operation.
12 VCC power_in Power connection for the device that should be bypassed to LGND with a ceramic capacitor placed as close to the VCC and LGND pins as possible.
13 PGND power_in Dedicated ground for the output gate driver, which must be connected to LGND with a short PCB trace and decoupled from VC with a low ESR 0.1µF or larger capacitor.
14 VC power_in Separate collector supply for the output gate drive, which should be decoupled to PGND with a low ESR 0.1µF or larger capacitor to isolate analog circuitry from gate drive noise.
15 GATE output High-current gate driver output capable of 1.0A peak current, with the output high voltage held to about 13.5V, and voltages exceeding this clamp must not be applied to the pin.
16 ISENSE input Input to the PWM peak-current comparator and the overcurrent comparator, where exceeding the overcurrent threshold starts a delayed shutdown sequence.
17 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer RENESAS
Package QFN-16-EP(3x3)
Category Power Supply Chip
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Voltage, VCC, VC VCC, VC -0.3 20 V Referenced to GND; min printed as GND - 0.3 10
GATE voltage GATE -0.3 V Min printed as GND - 0.3; max printed as Gate Output Limit Voltage (not numeric) 10
PGND to LGND -0.3 0.3 V 10
VREF VREF -0.3 5.3 V Min printed as GND - 0.3 10
Signal Pins -0.3 V Min printed as GND - 0.3; max printed as VREF (not numeric) 10
Peak GATE Current 1 A 10
Maximum Junction Temperature -55 150 °C 10
Maximum Storage Temperature Range -65 150 °C 10
Temperature Range -40 105 °C 10
Supply Voltage Range VCC 9 18 VDC Typical, Note 8; voltages measured with respect to GND 10
START Threshold 6.4 6.8 6.9 V 11
STOP Threshold 5.85 6.2 6.3 V 11
Start-Up Current ICC 100 175 µA VCC < START Threshold 11
OC/OV Fault Operating Current ICC 200 300 µA 11
Operating Current ICC 4.5 10 mA Note 11 11
Operating Supply Current IC 8 12 mA Includes 1nF GATE loading 11
Reference Overall Accuracy 4.95 5 5.05 V Line, load, 0°C to +105°C 11
Reference Overall Accuracy 4.9 5 5.05 V Line, load, -40°C to +105°C 11
Fault Voltage 4.5 4.65 4.75 V 11
VREF Good Voltage 4.65 4.8 4.95 V 11
Current Sense Offset Voltage 0.08 0.1 0.11 V 11
Blanking Time 30 60 100 ns Note 10 11
Gain ACS 0.77 0.79 0.81 V/V VSLOPE = 0V, VFB = 2.3V, VISET = 0.35V, 1.5V; ACS = ISET/ISENSE 11
Open Loop Voltage Gain 60 90 dB Note 10 11
Reference Voltage Initial Accuracy 2.465 2.515 2.565 V VFB = COMP, TA = +25°C; Note 10 11
Reference Voltage 2.44 2.515 2.59 V VFB = COMP 11
COMP to PWM Gain ACOMP 0.31 0.33 0.35 V/V COMP = 4V, TA = +25°C 11
COMP to PWM Offset 0.51 0.75 0.88 V COMP = 4V; Note 10 11
COMP VOH 4.25 4.4 5 V VFB = 2.3V 11
COMP VOL 0.4 0.8 1.2 V VFB = 2.7V 11
SS Clamp VCOMP 2.4 2.5 2.6 V SS = 2.5V, VFB = 0V, ISET = 2V 12
Oscillator Frequency Accuracy 289 318 347 kHz 12
Frequency Variation with VCC, T = +105°C -2 3 % (f20V - f9V)/f9V 12
Maximum Duty Cycle 68 75 81 % Note 12 12
Discharge Current, 0°C to +105°C 0.75 1 1.2 mA 0°C to +105°C 12
Synchronization Input High Threshold 2.5 V 12
Synchronization Input Pulse Width 25 ns 12
SYNC VOH VOH 2.5 V RLOAD = 4.5k 12
SYNC Advance 25 55 ns SYNC rising edge to GATE falling edge, CGATE = CSYNC = 100pF 12
Soft-Start Charging Current -40 -55 -70 µA SS = 2V 12
Soft-Start Charged Threshold Voltage 4.26 4.5 4.74 V 12
Initial Overcurrent Discharge Current 30 40 55 µA Sustained OC Threshold < SS < Charged Threshold 12
Overcurrent Shutdown Threshold Voltage 0.095 0.125 0.155 V Charged Threshold minus, TA = +25°C 12
Reset Threshold Voltage 0.22 0.27 0.31 V TA = +25°C 12
Slope Compensation Charge Current, 0°C to +105°C -45 -53 -65 µA SLOPE = 2V, 0°C to +105°C 12
Slope Compensation Gain 0.097 0.103 V/V Fraction of slope voltage added to ISENSE, TA = +25°C 12
Gate Output Limit Voltage 11 13.5 16 V VC = 20V, CGATE = 1nF, IOUT = 0mA 13
Gate VOH VOH 1.5 2.2 V VC - GATE, VC = 10V, IOUT = 150mA 13
Gate VOL VOL 1.2 1.5 V GATE - PGND, IOUT = 150mA 13
Gate Rise Time 60 100 ns VC = 20V, CGATE = 1nF, 1V < GATE < 9V 13
Minimum ISET Voltage 0.35 V 13
Maximum ISET Voltage 1.2 V 13
Restart Delay 150 295 445 ms TA = +25°C 13
Overvoltage Threshold 2.4 2.5 2.6 V 13
Undervoltage Fault Threshold 1.89 1.93 2 V 13
Undervoltage Clear Threshold 1.96 2.01 2.1 V 13
Thermal Shutdown 120 130 140 °C Note 10 13
Thermal Resistance junction-to-ambient (16 Ld QFN) θJA 44 °C/W Notes 4, 5: free air, high-effective thermal conductivity test board 10
Thermal Resistance junction-to-case (16 Ld QFN) θJC 4 °C/W Note 5: case temp at center of exposed metal pad 10

CAD (KiCad official)

  • Symbol: ISL6721AARZ-T
  • Footprint: Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm
  • 3D model: QFN-16-EP(3x3) (KiCad packages3D, STEP)
  • 3D model files: isl6721aarz-t-etched.step / isl6721aarz-t-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); isl6721aarz-t.step / isl6721aarz-t.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: RENESAS datasheet (36 pp, sha256 7672f9eae9bae5a3, retrieved 2026-10-30, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF