3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownISL6721AARZ-T
RENESAS · DC-DC Controllers · QFN-16-EP(3x3)
ISL6721AARZ-T from RENESAS, in a QFN-16-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SYNC | bidirectional | Bidirectional synchronization signal that coordinates the switching frequency of multiple units; the first unit to assert it takes control, and the SYNC frequency can be higher or lower than the free-running oscillator frequency. |
| 2 | SLOPE | passive | Slope compensation pin where an internal current source charges an external capacitor to GND each switching cycle, and the resulting scaled ramp is added to the ISENSE signal. |
| 3 | UV | input | Undervoltage monitor input compared to an internal 1.93V reference to detect an undervoltage condition. |
| 4 | OV | input | Overvoltage monitor input compared to an internal 2.5V reference to detect an overvoltage condition. |
| 5 | RTCT | passive | Oscillator timing pin, with timing resistor RT connected from VREF and timing capacitor CT connected from this pin to LGND, giving a programmable frequency range of 100kHz to 1.0MHz. |
| 6 | ISET | input | Sets the pulse-by-pulse overcurrent threshold when a DC voltage between 0.35V and 1.2V is applied to this input. |
| 7 | FB | input | Feedback voltage input connected to the inverting input of the error amplifier, and current sense leading edge blanking is disabled when FB is below 2.0V. |
| 8 | COMP | passive | Error amplifier output and PWM comparator input, with the loop frequency compensation network connected between COMP and FB, and soft-start implemented as a clamp on the maximum COMP voltage. |
| 9 | SS | passive | Soft-start capacitor connection to LGND that sets the soft-start duration and the overcurrent shutdown delay. |
| 10 | LGND | power_in | Small-signal reference ground for all analog functions on the device, to be connected externally to PGND with a short PCB trace close to the IC. |
| 11 | VREF | power_out | 5V reference voltage output that should be bypassed to LGND with a 0.01µF or larger capacitor, since smaller capacitance may cause unstable operation. |
| 12 | VCC | power_in | Power connection for the device that should be bypassed to LGND with a ceramic capacitor placed as close to the VCC and LGND pins as possible. |
| 13 | PGND | power_in | Dedicated ground for the output gate driver, which must be connected to LGND with a short PCB trace and decoupled from VC with a low ESR 0.1µF or larger capacitor. |
| 14 | VC | power_in | Separate collector supply for the output gate drive, which should be decoupled to PGND with a low ESR 0.1µF or larger capacitor to isolate analog circuitry from gate drive noise. |
| 15 | GATE | output | High-current gate driver output capable of 1.0A peak current, with the output high voltage held to about 13.5V, and voltages exceeding this clamp must not be applied to the pin. |
| 16 | ISENSE | input | Input to the PWM peak-current comparator and the overcurrent comparator, where exceeding the overcurrent threshold starts a delayed shutdown sequence. |
| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | RENESAS |
| Package | QFN-16-EP(3x3) |
| Category | Power Supply Chip |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage, VCC, VC | VCC, VC | -0.3 | 20 | V | Referenced to GND; min printed as GND - 0.3 | 10 | |
| GATE voltage | GATE | -0.3 | V | Min printed as GND - 0.3; max printed as Gate Output Limit Voltage (not numeric) | 10 | ||
| PGND to LGND | -0.3 | 0.3 | V | 10 | |||
| VREF | VREF | -0.3 | 5.3 | V | Min printed as GND - 0.3 | 10 | |
| Signal Pins | -0.3 | V | Min printed as GND - 0.3; max printed as VREF (not numeric) | 10 | |||
| Peak GATE Current | 1 | A | 10 | ||||
| Maximum Junction Temperature | -55 | 150 | °C | 10 | |||
| Maximum Storage Temperature Range | -65 | 150 | °C | 10 | |||
| Temperature Range | -40 | 105 | °C | 10 | |||
| Supply Voltage Range | VCC | 9 | 18 | VDC | Typical, Note 8; voltages measured with respect to GND | 10 | |
| START Threshold | 6.4 | 6.8 | 6.9 | V | 11 | ||
| STOP Threshold | 5.85 | 6.2 | 6.3 | V | 11 | ||
| Start-Up Current | ICC | 100 | 175 | µA | VCC < START Threshold | 11 | |
| OC/OV Fault Operating Current | ICC | 200 | 300 | µA | 11 | ||
| Operating Current | ICC | 4.5 | 10 | mA | Note 11 | 11 | |
| Operating Supply Current | IC | 8 | 12 | mA | Includes 1nF GATE loading | 11 | |
| Reference Overall Accuracy | 4.95 | 5 | 5.05 | V | Line, load, 0°C to +105°C | 11 | |
| Reference Overall Accuracy | 4.9 | 5 | 5.05 | V | Line, load, -40°C to +105°C | 11 | |
| Fault Voltage | 4.5 | 4.65 | 4.75 | V | 11 | ||
| VREF Good Voltage | 4.65 | 4.8 | 4.95 | V | 11 | ||
| Current Sense Offset Voltage | 0.08 | 0.1 | 0.11 | V | 11 | ||
| Blanking Time | 30 | 60 | 100 | ns | Note 10 | 11 | |
| Gain | ACS | 0.77 | 0.79 | 0.81 | V/V | VSLOPE = 0V, VFB = 2.3V, VISET = 0.35V, 1.5V; ACS = ISET/ISENSE | 11 |
| Open Loop Voltage Gain | 60 | 90 | dB | Note 10 | 11 | ||
| Reference Voltage Initial Accuracy | 2.465 | 2.515 | 2.565 | V | VFB = COMP, TA = +25°C; Note 10 | 11 | |
| Reference Voltage | 2.44 | 2.515 | 2.59 | V | VFB = COMP | 11 | |
| COMP to PWM Gain | ACOMP | 0.31 | 0.33 | 0.35 | V/V | COMP = 4V, TA = +25°C | 11 |
| COMP to PWM Offset | 0.51 | 0.75 | 0.88 | V | COMP = 4V; Note 10 | 11 | |
| COMP VOH | 4.25 | 4.4 | 5 | V | VFB = 2.3V | 11 | |
| COMP VOL | 0.4 | 0.8 | 1.2 | V | VFB = 2.7V | 11 | |
| SS Clamp | VCOMP | 2.4 | 2.5 | 2.6 | V | SS = 2.5V, VFB = 0V, ISET = 2V | 12 |
| Oscillator Frequency Accuracy | 289 | 318 | 347 | kHz | 12 | ||
| Frequency Variation with VCC, T = +105°C | -2 | 3 | % | (f20V - f9V)/f9V | 12 | ||
| Maximum Duty Cycle | 68 | 75 | 81 | % | Note 12 | 12 | |
| Discharge Current, 0°C to +105°C | 0.75 | 1 | 1.2 | mA | 0°C to +105°C | 12 | |
| Synchronization Input High Threshold | 2.5 | V | 12 | ||||
| Synchronization Input Pulse Width | 25 | ns | 12 | ||||
| SYNC VOH | VOH | 2.5 | V | RLOAD = 4.5k | 12 | ||
| SYNC Advance | 25 | 55 | ns | SYNC rising edge to GATE falling edge, CGATE = CSYNC = 100pF | 12 | ||
| Soft-Start Charging Current | -40 | -55 | -70 | µA | SS = 2V | 12 | |
| Soft-Start Charged Threshold Voltage | 4.26 | 4.5 | 4.74 | V | 12 | ||
| Initial Overcurrent Discharge Current | 30 | 40 | 55 | µA | Sustained OC Threshold < SS < Charged Threshold | 12 | |
| Overcurrent Shutdown Threshold Voltage | 0.095 | 0.125 | 0.155 | V | Charged Threshold minus, TA = +25°C | 12 | |
| Reset Threshold Voltage | 0.22 | 0.27 | 0.31 | V | TA = +25°C | 12 | |
| Slope Compensation Charge Current, 0°C to +105°C | -45 | -53 | -65 | µA | SLOPE = 2V, 0°C to +105°C | 12 | |
| Slope Compensation Gain | 0.097 | 0.103 | V/V | Fraction of slope voltage added to ISENSE, TA = +25°C | 12 | ||
| Gate Output Limit Voltage | 11 | 13.5 | 16 | V | VC = 20V, CGATE = 1nF, IOUT = 0mA | 13 | |
| Gate VOH | VOH | 1.5 | 2.2 | V | VC - GATE, VC = 10V, IOUT = 150mA | 13 | |
| Gate VOL | VOL | 1.2 | 1.5 | V | GATE - PGND, IOUT = 150mA | 13 | |
| Gate Rise Time | 60 | 100 | ns | VC = 20V, CGATE = 1nF, 1V < GATE < 9V | 13 | ||
| Minimum ISET Voltage | 0.35 | V | 13 | ||||
| Maximum ISET Voltage | 1.2 | V | 13 | ||||
| Restart Delay | 150 | 295 | 445 | ms | TA = +25°C | 13 | |
| Overvoltage Threshold | 2.4 | 2.5 | 2.6 | V | 13 | ||
| Undervoltage Fault Threshold | 1.89 | 1.93 | 2 | V | 13 | ||
| Undervoltage Clear Threshold | 1.96 | 2.01 | 2.1 | V | 13 | ||
| Thermal Shutdown | 120 | 130 | 140 | °C | Note 10 | 13 | |
| Thermal Resistance junction-to-ambient (16 Ld QFN) | θJA | 44 | °C/W | Notes 4, 5: free air, high-effective thermal conductivity test board | 10 | ||
| Thermal Resistance junction-to-case (16 Ld QFN) | θJC | 4 | °C/W | Note 5: case temp at center of exposed metal pad | 10 |
CAD (KiCad official)
- Symbol:
ISL6721AARZ-T - Footprint:
Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm - 3D model: QFN-16-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
isl6721aarz-t-etched.step/isl6721aarz-t-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);isl6721aarz-t.step/isl6721aarz-t.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: RENESAS datasheet (36 pp, sha256
7672f9eae9bae5a3, retrieved 2026-10-30, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).