main
Ray
Publish 0.1.0
3b072b6
ISL1208IU8Z
RENESAS · Real-time Clocks (RTC) · MSOP-8
ISL1208IU8Z from RENESAS, in a MSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | X1 | input | X1 is the input of an inverting amplifier intended to connect to one pin of an external 32.768kHz quartz crystal, and it can also be driven directly from a 32.768kHz source. |
| 2 | X2 | output | X2 is the output of an inverting amplifier intended to connect to the other pin of an external 32.768kHz quartz crystal. |
| 3 | VBAT | power_in | VBAT is the backup supply input that powers the device when VDD fails, with a 1.8 V to 5.5 V battery supply range, and it should be tied to ground if not used. |
| 4 | GND | power_in | GND is the ground reference pin for the device. |
| 5 | SDA | bidirectional | SDA is the open drain serial data pin used to transfer data into and out of the device, requires a pull-up resistor, and may be wire-OR'ed with other open drain or open collector outputs. |
| 6 | SCL | input | SCL is the serial clock input used to clock all serial data into and out of the device. |
| 7 | IRQ/FOUT | output | IRQ/FOUT is an open drain, active low multi-function pin that works as either an interrupt output or a frequency output, selected via the configuration register. |
| 8 | VDD | power_in | VDD is the main power supply pin, specified at 2.7 V to 5.5 V in the DC characteristics, and a 0.1 µF capacitor is recommended from VDD to ground. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | RENESAS |
| Package | MSOP-8 |
| Category | Clock and Timing |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VDD Main Power Supply | VDD | 2.7 | 5.5 | V | 3 | ||
| VBAT Battery Supply Voltage | VBAT | 1.8 | 5.5 | V | 3 | ||
| RTC operating temperature range | -40 | 85 | °C | RTC temperature, unless otherwise stated | 3 | ||
| Supply Current IDD1 | IDD1 | 2 | 6 | µA | VDD = 5V | 3 | |
| Supply Current IDD1 | IDD1 | 1.2 | 4 | µA | VDD = 3V | 3 | |
| Supply Current With I2C Active | IDD2 | 40 | 120 | µA | VDD = 5V | 3 | |
| Supply Current (Low Power Mode) | IDD3 | 1.4 | 5 | µA | VDD = 5V, LPMODE = 1 | 3 | |
| Battery Supply Current | IBAT | 400 | 950 | nA | VBAT = 3V | 3 | |
| Input Leakage Current on SCL | ILI | 100 | nA | 3 | |||
| I/O Leakage Current on SDA | ILO | 100 | nA | 3 | |||
| VBAT Mode Threshold | VTRIP | 1.6 | 2.2 | 2.6 | V | 3 | |
| VTRIP Hysteresis | VTRIPHYS | 10 | 30 | 75 | mV | 3 | |
| VBAT Hysteresis | VBATHYS | 15 | 50 | 100 | mV | 3 | |
| IRQ/FOUT Output Low Voltage | VOL | 0.4 | V | VDD = 5V, IOL = 3mA | 3 | ||
| SDA and SCL Input Buffer LOW Voltage | VIL | -0.3 | V | 4 | |||
| SDA Output Buffer LOW Voltage | VOL | 0 | 0.4 | V | Sinking 3mA | 4 | |
| SCL Frequency | fSCL | 400 | kHz | 4 | |||
| Pulse width suppression time at SDA and SCL inputs | tIN | 50 | ns | Any pulse narrower than the max spec is suppressed | 4 | ||
| SCL falling edge to SDA output data valid | tAA | 900 | ns | SCL falling edge crossing 30% of VDD, until SDA exits the 30% to 70% of VDD window | 4 | ||
| Time the bus must be free before the start of a new transmission | tBUF | 1300 | ns | SDA crossing 70% of VDD during a STOP condition, to SDA crossing 70% of VDD during the following START condition | 4 | ||
| Clock LOW time | tLOW | 1300 | ns | Measured at the 30% of VDD crossing | 4 | ||
| Clock HIGH time | tHIGH | 600 | ns | Measured at the 70% of VDD crossing | 4 | ||
| START condition setup time | tSU:STA | 600 | ns | SCL rising edge to SDA falling edge, both crossing 70% of VDD | 4 | ||
| START condition hold time | tHD:STA | 600 | ns | From SDA falling edge crossing 30% of VDD to SCL falling edge crossing 70% of VDD | 4 | ||
| Input data setup time | tSU:DAT | 100 | ns | From SDA exiting the 30% to 70% of VDD window, to SCL rising edge crossing 30% of VDD | 4 | ||
| Input data hold time | tHD:DAT | 20 | 900 | ns | From SCL falling edge crossing 30% of VDD to SDA entering the 30% to 70% of VDD window | 4 | |
| STOP condition setup time | tSU:STO | 600 | ns | From SCL rising edge crossing 70% of VDD, to SDA rising edge crossing 30% of VDD | 4 | ||
| STOP condition hold time | tHD:STO | 600 | ns | From SDA rising edge to SCL falling edge, both crossing 70% of VDD | 4 | ||
| Output data hold time | tDH | 0 | ns | From SCL falling edge crossing 30% of VDD, until SDA enters the 30% to 70% of VDD window | 4 | ||
| SDA and SCL rise time | tR | 300 | ns | From 30% to 70% of VDD; min is 20 + 0.1 x Cb | 4 | ||
| SDA and SCL fall time | tF | 300 | ns | From 70% to 30% of VDD; min is 20 + 0.1 x Cb | 4 | ||
| Capacitive loading of SDA or SCL | Cb | 10 | 400 | pF | Total on-chip and off-chip | 4 | |
| Voltage on VDD, VBAT, SCL, SDA, and IRQ pins (respect to GND) | -0.5 | 7 | V | 3 | |||
| Storage temperature | -65 | 150 | °C | 3 | |||
| Thermal resistance junction-to-ambient, MSOP package | θJA | 145 | °C/W | MSOP package, notes 5, 7 | 3 | ||
| Thermal resistance junction-to-case, MSOP package | θJC | 55 | °C/W | MSOP package, notes 6, 7 | 3 |
CAD (KiCad official)
- Symbol:
ISL1208IU8Z - Footprint:
Package_SO:MSOP-8_3x3mm_P0.65mm - 3D model: MSOP-8 (KiCad packages3D, STEP)
- 3D model files:
isl1208iu8z-etched.step/isl1208iu8z-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);isl1208iu8z.step/isl1208iu8z.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: RENESAS datasheet (24 pp, sha256
bda9903d64f3a077, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# ISL1208IU8Z
**RENESAS** · Real-time Clocks (RTC) · MSOP-8
ISL1208IU8Z from RENESAS, in a MSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | X1 | input | X1 is the input of an inverting amplifier intended to connect to one pin of an external 32.768kHz quartz crystal, and it can also be driven directly from a 32.768kHz source. |
| 2 | X2 | output | X2 is the output of an inverting amplifier intended to connect to the other pin of an external 32.768kHz quartz crystal. |
| 3 | VBAT | power_in | VBAT is the backup supply input that powers the device when VDD fails, with a 1.8 V to 5.5 V battery supply range, and it should be tied to ground if not used. |
| 4 | GND | power_in | GND is the ground reference pin for the device. |
| 5 | SDA | bidirectional | SDA is the open drain serial data pin used to transfer data into and out of the device, requires a pull-up resistor, and may be wire-OR'ed with other open drain or open collector outputs. |
| 6 | SCL | input | SCL is the serial clock input used to clock all serial data into and out of the device. |
| 7 | IRQ/FOUT | output | IRQ/FOUT is an open drain, active low multi-function pin that works as either an interrupt output or a frequency output, selected via the configuration register. |
| 8 | VDD | power_in | VDD is the main power supply pin, specified at 2.7 V to 5.5 V in the DC characteristics, and a 0.1 µF capacitor is recommended from VDD to ground. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | RENESAS |
| Package | MSOP-8 |
| Category | Clock and Timing |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VDD Main Power Supply | VDD | 2.7 | | 5.5 | V | | 3 |
| VBAT Battery Supply Voltage | VBAT | 1.8 | | 5.5 | V | | 3 |
| RTC operating temperature range | | -40 | | 85 | °C | RTC temperature, unless otherwise stated | 3 |
| Supply Current IDD1 | IDD1 | | 2 | 6 | µA | VDD = 5V | 3 |
| Supply Current IDD1 | IDD1 | | 1.2 | 4 | µA | VDD = 3V | 3 |
| Supply Current With I2C Active | IDD2 | | 40 | 120 | µA | VDD = 5V | 3 |
| Supply Current (Low Power Mode) | IDD3 | | 1.4 | 5 | µA | VDD = 5V, LPMODE = 1 | 3 |
| Battery Supply Current | IBAT | | 400 | 950 | nA | VBAT = 3V | 3 |
| Input Leakage Current on SCL | ILI | | | 100 | nA | | 3 |
| I/O Leakage Current on SDA | ILO | | | 100 | nA | | 3 |
| VBAT Mode Threshold | VTRIP | 1.6 | 2.2 | 2.6 | V | | 3 |
| VTRIP Hysteresis | VTRIPHYS | 10 | 30 | 75 | mV | | 3 |
| VBAT Hysteresis | VBATHYS | 15 | 50 | 100 | mV | | 3 |
| IRQ/FOUT Output Low Voltage | VOL | | | 0.4 | V | VDD = 5V, IOL = 3mA | 3 |
| SDA and SCL Input Buffer LOW Voltage | VIL | -0.3 | | | V | | 4 |
| SDA Output Buffer LOW Voltage | VOL | 0 | | 0.4 | V | Sinking 3mA | 4 |
| SCL Frequency | fSCL | | | 400 | kHz | | 4 |
| Pulse width suppression time at SDA and SCL inputs | tIN | | | 50 | ns | Any pulse narrower than the max spec is suppressed | 4 |
| SCL falling edge to SDA output data valid | tAA | | | 900 | ns | SCL falling edge crossing 30% of VDD, until SDA exits the 30% to 70% of VDD window | 4 |
| Time the bus must be free before the start of a new transmission | tBUF | 1300 | | | ns | SDA crossing 70% of VDD during a STOP condition, to SDA crossing 70% of VDD during the following START condition | 4 |
| Clock LOW time | tLOW | 1300 | | | ns | Measured at the 30% of VDD crossing | 4 |
| Clock HIGH time | tHIGH | 600 | | | ns | Measured at the 70% of VDD crossing | 4 |
| START condition setup time | tSU:STA | 600 | | | ns | SCL rising edge to SDA falling edge, both crossing 70% of VDD | 4 |
| START condition hold time | tHD:STA | 600 | | | ns | From SDA falling edge crossing 30% of VDD to SCL falling edge crossing 70% of VDD | 4 |
| Input data setup time | tSU:DAT | 100 | | | ns | From SDA exiting the 30% to 70% of VDD window, to SCL rising edge crossing 30% of VDD | 4 |
| Input data hold time | tHD:DAT | 20 | | 900 | ns | From SCL falling edge crossing 30% of VDD to SDA entering the 30% to 70% of VDD window | 4 |
| STOP condition setup time | tSU:STO | 600 | | | ns | From SCL rising edge crossing 70% of VDD, to SDA rising edge crossing 30% of VDD | 4 |
| STOP condition hold time | tHD:STO | 600 | | | ns | From SDA rising edge to SCL falling edge, both crossing 70% of VDD | 4 |
| Output data hold time | tDH | 0 | | | ns | From SCL falling edge crossing 30% of VDD, until SDA enters the 30% to 70% of VDD window | 4 |
| SDA and SCL rise time | tR | | | 300 | ns | From 30% to 70% of VDD; min is 20 + 0.1 x Cb | 4 |
| SDA and SCL fall time | tF | | | 300 | ns | From 70% to 30% of VDD; min is 20 + 0.1 x Cb | 4 |
| Capacitive loading of SDA or SCL | Cb | 10 | | 400 | pF | Total on-chip and off-chip | 4 |
| Voltage on VDD, VBAT, SCL, SDA, and IRQ pins (respect to GND) | | -0.5 | | 7 | V | | 3 |
| Storage temperature | | -65 | | 150 | °C | | 3 |
| Thermal resistance junction-to-ambient, MSOP package | θJA | | 145 | | °C/W | MSOP package, notes 5, 7 | 3 |
| Thermal resistance junction-to-case, MSOP package | θJC | | 55 | | °C/W | MSOP package, notes 6, 7 | 3 |
## CAD (KiCad official)
- Symbol: `ISL1208IU8Z`
- Footprint: `Package_SO:MSOP-8_3x3mm_P0.65mm`
- 3D model: MSOP-8 (KiCad packages3D, STEP)
- 3D model files: `isl1208iu8z-etched.step` / `isl1208iu8z-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `isl1208iu8z.step` / `isl1208iu8z.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [RENESAS datasheet](docs/isl1208iu8z-datasheet.pdf) (24 pp, sha256 `bda9903d64f3a077`, retrieved 2026-10-30, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/isl1208iu8z-datasheet.pdf)