main
History Download
Ray Publish 0.1.0 9b6e250

ISL12026IBZ-T

Intersil(Renesas Electronics) · Real-time Clocks (RTC) · SOIC-8

ISL12026IBZ-T from Intersil(Renesas Electronics), in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 X1 input Input of the inverting oscillator amplifier, intended to connect to one pin of an external 32.768kHz quartz crystal, and it can also be driven directly from a 32.768kHz source.
2 X2 output Output of the inverting oscillator amplifier, intended to connect to the other pin of an external 32.768kHz quartz crystal.
3 IRQ/FOUT output Multi-function interrupt or frequency output pin, selected through the control register, and it is an open-drain output.
4 GND power_in Ground reference for the device.
5 SDA bidirectional Serial data line for transferring data into and out of the device, with an open-drain output that may be wire-OR'ed with other open-drain or open-collector outputs.
6 SCL input Serial clock input used to clock all serial data into and out of the device, with an input buffer that is always active (not gated).
7 VBAT power_in Backup supply input that powers the device when VDD fails, with the datasheet specifying VBAT of 1.8 V to 5.5 V and advising to tie it to ground if not used.
8 VDD power_in Main power supply input, with the datasheet specifying VDD of 2.7 V to 5.5 V.

Key specifications

Parameter Value
Manufacturer Intersil(Renesas Electronics)
Package SOIC-8
Category Clock and Timing
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Main Power Supply VDD VDD 2.7 5.5 V 3
Backup Power Supply VBAT VBAT 1.8 5.5 V 3
Operating temperature range (ordering table) -40 85 °C Temp range as printed in ordering information 1
Supply Current with I2C Active IDD1 IDD1 500 µA VDD = 2.7V 3
Supply Current with I2C Active IDD1 IDD1 800 µA VDD = 5.5V 3
Supply Current for Non-Volatile Programming IDD2 IDD2 2.5 mA VDD = 2.7V 3
Supply Current for Non-Volatile Programming IDD2 IDD2 3.5 mA VDD = 5.5V 3
Supply Current for Main Timekeeping (Low Power Mode) IDD3 IDD3 10 µA VDD = VSDA = VSCL = 2.7V 3
Supply Current for Main Timekeeping (Low Power Mode) IDD3 IDD3 20 µA VDD = VSDA = VSCL = 5.5V 3
Battery Supply Current IBAT IBAT 800 1000 nA VBAT = 1.8V, VDD = VSDA = VSCL = VRESET = 0 3
Battery Supply Current IBAT IBAT 850 1200 nA VBAT = 3.0V, VDD = VSDA = VSCL = VRESET = 0 3
Battery Input Leakage IBATLKG IBATLKG 100 nA VDD = 5.5V, VBAT = 1.8V 3
VBAT Mode Threshold VTRIP VTRIP 1.8 2.2 2.6 V 3
VTRIP Hysteresis VTRIPHYS VTRIPHYS 30 mV 3
VBAT Hysteresis VBATHYS VBATHYS 50 mV 3
VDD Negative Slew Rate VDD SR- 10 V/ms 3
IRQ/FOUT Output Low Voltage VOL 0.4 V VDD = 5V, IOL = 3mA 3
IRQ/FOUT Output Leakage Current ILO 100 400 nA VDD = 5.5V, VOUT = 5.5V 3
Voltage on VDD, VBAT, SCL, SDA, IRQ/FOUT pins -0.3 6 V With respect to ground 3
Voltage on X1 and X2 pins -0.3 2.5 V With respect to ground 3
ESD Rating (MIL-STD-883, Method 3014) -2 2 kV Printed as >±2kV 3
ESD Rating (Machine Model) 175 V Printed as >175V 3
Storage Temperature -65 150 °C 3
Lead Temperature (Soldering) 300 °C Soldering, 10s 3
Thermal Resistance θJA, 8 Ld SOIC θJA 120 °C/W 8 Ld SOIC package, component on high effective thermal conductivity test board 3
VIL SDA and SCL Input Buffer LOW Voltage VIL -0.3 V Maximum printed as 0.3 x VDD 4
VOL SDA Output Buffer LOW Voltage VOL 0 0.4 V IOL = 4mA 4
ILI Input Leakage Current on SCL ILI 100 nA VIN = 5.5V 4
ILO I/O Leakage Current on SDA ILO 100 nA VIN = 5.5V 4
EEPROM Endurance 2e+06 cycles Printed as >2,000,000 cycles per byte 4
EEPROM Retention 50 Years Temperature ≤75°C 4
SCL Frequency fSCL fSCL 400 kHz 4
Pulse width Suppression Time at SDA and SCL Inputs tIN tIN 50 ns Any pulse narrower than the max spec is suppressed 4
SCL Falling Edge to SDA Output Data Valid tAA tAA 900 ns SCL falling edge crossing 30% of VDD, until SDA exits the 30% to 70% of VDD window 4
Time the Bus Must be Free Before the Start of a New Transmission tBUF tBUF 1300 ns SDA crossing 70% of VDD during STOP to SDA crossing 70% of VDD during following START 4
Clock LOW Time tLOW tLOW 1300 ns Measured at the 30% of VDD crossing 4
Clock HIGH Time tHIGH tHIGH 600 ns Measured at the 70% of VDD crossing 4
START Condition Setup Time tSU:STA tSU:STA 600 ns SCL rising edge to SDA falling edge, both crossing 70% of VDD 4
START Condition Hold Time tHD:STA tHD:STA 600 ns From SDA falling edge crossing 30% of VDD to SCL falling edge crossing 70% of VDD 4
Input Data Setup Time tSU:DAT tSU:DAT 100 ns From SDA exiting the 30% to 70% of VDD window, to SCL rising edge crossing 30% of VDD 4
Input Data Hold Time tHD:DAT tHD:DAT 0 ns From SCL rising edge crossing 70% of VDD to SDA entering the 30% to 70% of VDD window 4
STOP Condition Setup Time tSU:STO tSU:STO 600 ns From SCL rising edge crossing 70% of VDD, to SDA rising edge crossing 30% of VDD 4

CAD (KiCad official)

  • Symbol: ISL12026IBZ-T
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SOIC-8 (KiCad packages3D, STEP)
  • 3D model files: isl12026ibz-t-etched.step / isl12026ibz-t-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); isl12026ibz-t.step / isl12026ibz-t.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Intersil(Renesas Electronics) datasheet (24 pp, sha256 87807f0dcde4a525, retrieved 2026-10-30, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF