main
Ray Publish 0.1.0 12013a3

IS25LP010E-JNLE

ISSI(Integrated Silicon Solution) · NOR FLASH · SOIC-8

IS25LP010E-JNLE from ISSI(Integrated Silicon Solution), in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 CE# input Chip Enable: when high the device is deselected, outputs are high-impedance and it enters low-power standby; it must go from high to low before a new instruction is accepted.
2 SO (IO1) bidirectional Serial Data Output in standard SPI (data read on falling edge of SCK) and bidirectional IO1 in Dual/Quad SPI and QPI.
3 WP# (IO2) bidirectional Write Protect that, with the SRWD bit, protects the Status Register when pulled low; becomes IO2 when the QE bit is set to 1.
4 GND power_in Ground reference for Vcc.
5 SI (IO0) bidirectional Serial Data Input for instructions, addresses and data on the rising edge of SCK, and bidirectional IO0 in Dual/Quad SPI and QPI.
6 SCK input Serial Data Clock: synchronizes input and output timing, supports SPI modes 0 and 3 with up to 104MHz fast read.
7 HOLD# (IO3) bidirectional Active-low Hold pauses serial communication without resetting the sequence while selected; becomes IO3 when the QE bit is set to 1.
8 Vcc power_in Device core power supply, 2.30V to 3.60V for IS25LP.

Key specifications

Parameter Value
Manufacturer ISSI(Integrated Silicon Solution)
Package SOIC-8
Category Memory
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VCC Power Supply (IS25LP) VCC 2.3 3 3.6 V IS25LP 77
Ambient Operating Temperature, Extended Grade E -40 105 °C Extended Grade E 77
Storage Temperature -65 150 °C 77
Lead Soldering Temperature, Lead-free Package 260 °C 3 Seconds, surface mount 77
VCC supply voltage (IS25LP) VCC -0.5 6 V IS25LP 77
Input Voltage on All Pins (lower limit) -0.5 V With respect to ground; upper limit VCC + 0.5V 77
Output Voltage on All Pins (lower limit) -0.5 V With respect to ground; upper limit VCC + 0.5V 77
VCC Active Read current, NORD ICC1 6 8 mA NORD at 50MHz 78
VCC Active Read current, FRD Single ICC1 7 9 mA FRD Single at 104MHz 78
VCC Active Read current, FRD Dual ICC1 8 10 mA FRD Dual at 104MHz 78
VCC Active Read current, FRD Quad ICC1 10 12 mA FRD Quad at 104MHz 78
VCC Program Current ICC2 15 20 mA CE# = VCC, 85°C 78
VCC Program Current ICC2 20 mA CE# = VCC, 105°C 78
VCC WRSR Current ICC3 15 20 mA CE# = VCC, 85°C 78
VCC WRSR Current ICC3 20 mA CE# = VCC, 105°C 78
VCC Erase Current (SER/BER4K/BER64K) ICC4 15 20 mA CE# = VCC, 85°C 78
VCC Erase Current (SER/BER4K/BER64K) ICC4 20 mA CE# = VCC, 105°C 78
VCC Erase Current (CE) ICC5 15 20 mA CE# = VCC, 85°C 78
VCC Erase Current (CE) ICC5 20 mA CE# = VCC, 105°C 78
VCC Standby Current CMOS ISB1 17 35 µA CE# = VCC, VIN = GND or VCC, 85°C 78
VCC Standby Current CMOS ISB1 40 µA CE# = VCC, VIN = GND or VCC, 105°C 78
Deep power down current (IS25LP) ISB2 6 15 µA CE# = VCC, VIN = GND or VCC, 85°C 78
Deep power down current (IS25LP) ISB2 18 µA CE# = VCC, VIN = GND or VCC, 105°C 78
Input Leakage Current ILI 1 µA VIN = 0V to VCC 78
Output Leakage Current ILO 1 µA VIN = 0V to VCC 78
Input Low Voltage (lower limit) VIL -0.5 V Max is 0.3VCC 78
Input Low Voltage (upper limit, fraction of VCC) VIL 0.3 VCC Printed as 0.3VCC 78
Input High Voltage (lower limit, fraction of VCC) VIH 0.7 VCC Printed as 0.7VCC; max is VCC + 0.3 78
Output Low Voltage VOL 0.2 V VMIN < VCC < VMAX, IOL = 100 µA 78
Input Capacitance (CE#, SCK) CIN 6 pF TA = 25°C, VCC=3V, 1MHz, VIN = 0V, IS25LP 79
Input/Output Capacitance (other pins) CIN/OUT 8 pF TA = 25°C, VCC=3V, 1MHz, VIN/OUT = 0V, IS25LP 79
Clock Frequency for fast read mode fCT 0 104 MHz 80
Clock Frequency for read mode fC 0 50 MHz 80
SCK High Time tCKH 4 ns 80
SCK Low Time tCKL 4 ns 80
CE# High Time tCEH 7 ns 80
Data In Setup Time tDS 2 ns 80
Data in Hold Time tDH 2 ns 80
Output Valid tV 8 ns 80
Output Hold Time tOH 2 ns 80
Output Disable Time tDIS 8 ns 80
Sector Erase Time (4Kbyte) tEC 70 300 ms 80
Block Erase Time (32Kbyte) tEC 130 500 ms 80
Block Erase time (64Kbyte) tEC 200 1000 ms 80
Chip Erase Time 1Mb tEC 0.4 1.5 s 1Mb 80
Page Program Time tPP 0.45 1.2 ms 80
Release deep power down (IS25LP) tres1 3 µs IS25LP 80
Deep power down tDP 3 µs 80
Write Status Register time tW 2 10 ms 80
Vcc(min) to CE# Low tVCE 300 us 84
Write Inhibit Voltage (IS25LP) VWI 2.1 V IS25LP 84
Byte Program 8 40 µs 85
Endurance 100000 Cycles JEDEC Standard A117 85
Data Retention 20 Years JEDEC Standard A117 85
Latch-Up -100 100 mA JEDEC Standard 78 85

CAD (KiCad official)

  • Symbol: IS25LP010E-JNLE
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SOIC-8 (KiCad packages3D, STEP)
  • 3D model files: is25lp010e-jnle-etched.step / is25lp010e-jnle-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); is25lp010e-jnle.step / is25lp010e-jnle.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: ISSI(Integrated Silicon Solution) datasheet (93 pp, sha256 682d1cb75600d9cd, retrieved 2026-10-23, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF