Generated by kicad-footprint-generator · KiCad file format 20260206
IS25LP010E-JNLE
ISSI(Integrated Silicon Solution) · NOR FLASH · SOIC-8
IS25LP010E-JNLE from ISSI(Integrated Silicon Solution), in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CE# | input | Chip Enable: when high the device is deselected, outputs are high-impedance and it enters low-power standby; it must go from high to low before a new instruction is accepted. |
| 2 | SO (IO1) | bidirectional | Serial Data Output in standard SPI (data read on falling edge of SCK) and bidirectional IO1 in Dual/Quad SPI and QPI. |
| 3 | WP# (IO2) | bidirectional | Write Protect that, with the SRWD bit, protects the Status Register when pulled low; becomes IO2 when the QE bit is set to 1. |
| 4 | GND | power_in | Ground reference for Vcc. |
| 5 | SI (IO0) | bidirectional | Serial Data Input for instructions, addresses and data on the rising edge of SCK, and bidirectional IO0 in Dual/Quad SPI and QPI. |
| 6 | SCK | input | Serial Data Clock: synchronizes input and output timing, supports SPI modes 0 and 3 with up to 104MHz fast read. |
| 7 | HOLD# (IO3) | bidirectional | Active-low Hold pauses serial communication without resetting the sequence while selected; becomes IO3 when the QE bit is set to 1. |
| 8 | Vcc | power_in | Device core power supply, 2.30V to 3.60V for IS25LP. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | ISSI(Integrated Silicon Solution) |
| Package | SOIC-8 |
| Category | Memory |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VCC Power Supply (IS25LP) | VCC | 2.3 | 3 | 3.6 | V | IS25LP | 77 |
| Ambient Operating Temperature, Extended Grade E | -40 | 105 | °C | Extended Grade E | 77 | ||
| Storage Temperature | -65 | 150 | °C | 77 | |||
| Lead Soldering Temperature, Lead-free Package | 260 | °C | 3 Seconds, surface mount | 77 | |||
| VCC supply voltage (IS25LP) | VCC | -0.5 | 6 | V | IS25LP | 77 | |
| Input Voltage on All Pins (lower limit) | -0.5 | V | With respect to ground; upper limit VCC + 0.5V | 77 | |||
| Output Voltage on All Pins (lower limit) | -0.5 | V | With respect to ground; upper limit VCC + 0.5V | 77 | |||
| VCC Active Read current, NORD | ICC1 | 6 | 8 | mA | NORD at 50MHz | 78 | |
| VCC Active Read current, FRD Single | ICC1 | 7 | 9 | mA | FRD Single at 104MHz | 78 | |
| VCC Active Read current, FRD Dual | ICC1 | 8 | 10 | mA | FRD Dual at 104MHz | 78 | |
| VCC Active Read current, FRD Quad | ICC1 | 10 | 12 | mA | FRD Quad at 104MHz | 78 | |
| VCC Program Current | ICC2 | 15 | 20 | mA | CE# = VCC, 85°C | 78 | |
| VCC Program Current | ICC2 | 20 | mA | CE# = VCC, 105°C | 78 | ||
| VCC WRSR Current | ICC3 | 15 | 20 | mA | CE# = VCC, 85°C | 78 | |
| VCC WRSR Current | ICC3 | 20 | mA | CE# = VCC, 105°C | 78 | ||
| VCC Erase Current (SER/BER4K/BER64K) | ICC4 | 15 | 20 | mA | CE# = VCC, 85°C | 78 | |
| VCC Erase Current (SER/BER4K/BER64K) | ICC4 | 20 | mA | CE# = VCC, 105°C | 78 | ||
| VCC Erase Current (CE) | ICC5 | 15 | 20 | mA | CE# = VCC, 85°C | 78 | |
| VCC Erase Current (CE) | ICC5 | 20 | mA | CE# = VCC, 105°C | 78 | ||
| VCC Standby Current CMOS | ISB1 | 17 | 35 | µA | CE# = VCC, VIN = GND or VCC, 85°C | 78 | |
| VCC Standby Current CMOS | ISB1 | 40 | µA | CE# = VCC, VIN = GND or VCC, 105°C | 78 | ||
| Deep power down current (IS25LP) | ISB2 | 6 | 15 | µA | CE# = VCC, VIN = GND or VCC, 85°C | 78 | |
| Deep power down current (IS25LP) | ISB2 | 18 | µA | CE# = VCC, VIN = GND or VCC, 105°C | 78 | ||
| Input Leakage Current | ILI | 1 | µA | VIN = 0V to VCC | 78 | ||
| Output Leakage Current | ILO | 1 | µA | VIN = 0V to VCC | 78 | ||
| Input Low Voltage (lower limit) | VIL | -0.5 | V | Max is 0.3VCC | 78 | ||
| Input Low Voltage (upper limit, fraction of VCC) | VIL | 0.3 | VCC | Printed as 0.3VCC | 78 | ||
| Input High Voltage (lower limit, fraction of VCC) | VIH | 0.7 | VCC | Printed as 0.7VCC; max is VCC + 0.3 | 78 | ||
| Output Low Voltage | VOL | 0.2 | V | VMIN < VCC < VMAX, IOL = 100 µA | 78 | ||
| Input Capacitance (CE#, SCK) | CIN | 6 | pF | TA = 25°C, VCC=3V, 1MHz, VIN = 0V, IS25LP | 79 | ||
| Input/Output Capacitance (other pins) | CIN/OUT | 8 | pF | TA = 25°C, VCC=3V, 1MHz, VIN/OUT = 0V, IS25LP | 79 | ||
| Clock Frequency for fast read mode | fCT | 0 | 104 | MHz | 80 | ||
| Clock Frequency for read mode | fC | 0 | 50 | MHz | 80 | ||
| SCK High Time | tCKH | 4 | ns | 80 | |||
| SCK Low Time | tCKL | 4 | ns | 80 | |||
| CE# High Time | tCEH | 7 | ns | 80 | |||
| Data In Setup Time | tDS | 2 | ns | 80 | |||
| Data in Hold Time | tDH | 2 | ns | 80 | |||
| Output Valid | tV | 8 | ns | 80 | |||
| Output Hold Time | tOH | 2 | ns | 80 | |||
| Output Disable Time | tDIS | 8 | ns | 80 | |||
| Sector Erase Time (4Kbyte) | tEC | 70 | 300 | ms | 80 | ||
| Block Erase Time (32Kbyte) | tEC | 130 | 500 | ms | 80 | ||
| Block Erase time (64Kbyte) | tEC | 200 | 1000 | ms | 80 | ||
| Chip Erase Time 1Mb | tEC | 0.4 | 1.5 | s | 1Mb | 80 | |
| Page Program Time | tPP | 0.45 | 1.2 | ms | 80 | ||
| Release deep power down (IS25LP) | tres1 | 3 | µs | IS25LP | 80 | ||
| Deep power down | tDP | 3 | µs | 80 | |||
| Write Status Register time | tW | 2 | 10 | ms | 80 | ||
| Vcc(min) to CE# Low | tVCE | 300 | us | 84 | |||
| Write Inhibit Voltage (IS25LP) | VWI | 2.1 | V | IS25LP | 84 | ||
| Byte Program | 8 | 40 | µs | 85 | |||
| Endurance | 100000 | Cycles | JEDEC Standard A117 | 85 | |||
| Data Retention | 20 | Years | JEDEC Standard A117 | 85 | |||
| Latch-Up | -100 | 100 | mA | JEDEC Standard 78 | 85 |
CAD (KiCad official)
- Symbol:
IS25LP010E-JNLE - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOIC-8 (KiCad packages3D, STEP)
- 3D model files:
is25lp010e-jnle-etched.step/is25lp010e-jnle-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);is25lp010e-jnle.step/is25lp010e-jnle.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: ISSI(Integrated Silicon Solution) datasheet (93 pp, sha256
682d1cb75600d9cd, retrieved 2026-10-23, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).