Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

INA331AIDGKT

Texas Instruments · Instrumentation Amplifiers · VSSOP-8

INA331AIDGKT from Texas Instruments, in a VSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 RG passive Gain-setting resistor terminal; connect external resistors between this pin and V- to set gain G = 5 + 5(R2/R1) for gains greater than 5V/V.
2 VIN- power_in Negative differential input signal terminal; common-mode range 0.55V to 3.8V at 5V supply; input impedance 10¹³Ω
3 VIN+ power_in Positive differential input signal terminal; common-mode range 0.55V to 3.8V at 5V supply; input impedance 10¹³Ω
4 V- power_in Negative power supply pin (ground in single-supply or negative rail in dual-supply mode); maximum supply voltage V+ to V- of 7.5V.
5 REF input Reference voltage input defining zero output level; requires low-impedance source ≤160Ω to preserve CMRR ≥80dB.
6 VOUT output Amplified differential output signal; swings within 50mV of supply rails for gains ≥10 with 10kΩ load; slew rate 5V/µs typical.
7 V+ power_in Positive power supply input; specified operating range +2.7V to +5.5V with quiescent current 415µA to 490µA.
8 Shutdown input Shutdown control input; pull below 0.8V to enter sleep mode drawing <2µA; float or tie to V+ for normal operation.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package VSSOP-8
Category Amplifiers/Comparators
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input Offset Voltage, RTI -500 250 500 µV VS = +5V 3
Input Offset Voltage over temperature VOS -2.1 1.7 2.1 mV Over Temperature 3
Power Supply Rejection Ratio vs Power Supply PSRR -200 50 200 µV/V VS = +2.7V to +5.5V 3
Common-Mode Rejection Ratio CMRR 90 94 dB VS = 5V, VCM = 0.55V to 3.8V 3
Common-Mode Rejection Ratio, –40°C to +85°C CMRR 77 dB –40°C to +85°C, VS = 5V, VCM = 0.55V to 3.8V 3
Common-Mode Rejection Ratio over temperature CMRR 72 dB Over Temperature, VS = 5V, VCM = 0.55V to 3.8V 3
Input Common-Mode Range 0.35 1.5 V VS = 2.7V 3
Input Common-Mode Range 0.55 3.8 V VS = 5V 3
Input Bias Current IB -10 0.5 10 pA VCM = VS /2 3
Input Offset Current IOS -10 0.5 10 pA VCM = VS /2 3
Range of Gain 5 1000 V/V 3
Gain Error -0.1 0.02 0.1 % G = 5 3
Gain Error vs Temperature -10 2 10 ppm/°C G = 5 3
Nonlinearity -0.01 0.001 0.01 % of FS G = 25, VS = 5V, VO = 0.05 to 4.95 3
Nonlinearity over temperature -0.015 0.002 0.015 % of FS Over Temperature 3
Output Voltage Swing from Rail 25 50 mV RL = 10kΩ 3
Output Voltage Swing from Rail over temperature 50 mV Over Temperature, G > 10 3
Short-Circuit Current ISC -32 48 mA 3
Specified Voltage Range 2.7 5.5 V 3
Operating Voltage Range 2.5 5.5 V 3
Quiescent Current per Channel IQ 415 490 µA VSD > 2.5 3
Quiescent Current per Channel over temperature IQ 600 µA Over Temperature 3
Shutdown Quiescent Current per Channel ISD 0.01 1 µA VSD < 0.8 3
Specified/Operating Temperature Range -55 125 °C 3
Storage Temperature Range -65 150 °C 3
Thermal Resistance, junction to ambient θJA 150 °C/W MSOP-8, TSSOP-14 surface mount 3
Supply Voltage, V+ to V– 7.5 V 2
Signal Input Terminals Voltage -0.5 0.5 V Referenced to (V–) and (V+) supply rails 2
Signal Input Terminals Current 10 mA Signal input terminals 2
Operating Temperature -55 125 °C 2
Junction Temperature 150 °C 2
Lead Temperature 300 °C Soldering, 10s 2

CAD (KiCad official)

  • Symbol: INA331AIDGKT
  • Footprint: Package_SO:VSSOP-8_2.3x2mm_P0.5mm
  • 3D model: VSSOP-8 (KiCad packages3D, STEP)
  • 3D model files: ina331aidgkt-etched.step / ina331aidgkt-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ina331aidgkt.step / ina331aidgkt.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (24 pp, sha256 b563b3023a3cb8c8, retrieved 2026-09-26, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.2, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-4-6 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF