Generated by kicad-footprint-generator · KiCad file format 20260206
INA199C2DCKR
Texas Instruments · Current Sense Amplifiers · SC-70-6
INA199C2DCKR from Texas Instruments, in a SC-70-6. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | REF | input | Reference voltage input (0V to V+) that sets the output DC operating point at zero differential input; enables single-ended or bipolar current measurement configuration. |
| 2 | GND | power_in | Analog ground connection serving as the reference potential for all input and output signal measurements throughout the device. |
| 3 | V+ | power_in | Positive power supply input accepting 2.7V to 26V to provide bias current for internal amplifier circuitry and set output voltage range. |
| 4 | IN+ | input | Non-inverting differential input connected to the power-side of the shunt resistor; withstands common-mode voltage from -0.1V to 26V independent of supply voltage per C-version specification. |
| 5 | IN- | input | Inverting differential input connected to the load-side of the shunt resistor; the voltage difference (IN+) − (IN−) produces an output voltage amplified by the gain of 100V/V for C2 variant. |
| 6 | OUT | output | Analog output voltage with swing from approximately 0.05V above GND to (V+)−0.2V below supply rail at 10kΩ load; changes from REF voltage proportionally to input differential voltage. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SC-70-6 |
| Category | Amplifiers/Comparators |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Common-mode input voltage range (version B and C) | VCM | -0.1 | 26 | V | 版本 B 和 C,TA = –40°C 至 125°C | 6 | |
| Common-mode rejection ratio | CMR | 100 | 120 | dB | VIN+ = 0V 至 26V,VSENSE = 0mV,TA = –40°C 至 125°C | 6 | |
| Input offset voltage, RTI | VOS | -150 | 5 | 150 | μV | VSENSE = 0mV | 6 |
| Offset voltage drift vs temperature | dVOS/dT | 0.1 | 0.5 | μV/°C | TA = –40°C 至 125°C | 6 | |
| Power supply rejection | PSR | -0.1 | 0.1 | μV/V | VS = 2.7V 至 18V,VIN+ = 18V,VSENSE = 0mV | 6 | |
| Input offset current | IOS | -0.02 | 0.02 | μA | VSENSE = 0mV | 6 | |
| Gain error (version C) | -1 | 0.03 | 1 | % | 版本 C,VSENSE = –5mV 至 5mV,TA = –40°C 至 125°C | 6 | |
| Gain error vs temperature | 3 | 10 | ppm/°C | TA = –40°C 至 125°C | 6 | ||
| Nonlinearity error | -0.01 | 0.01 | % | VSENSE = -5 mV 至 5 mV | 6 | ||
| Maximum capacitive load | 1 | nF | 无持续振荡 | 6 | |||
| Output swing to GND | 0.005 | 0.05 | V | RL = 10kΩ 至 GND,TA = –40°C 至 125°C | 6 | ||
| Supply voltage operating range (TA -40 to 125°C) | VS | 2.7 | 26 | V | TA = –40°C 至 125°C | 6 | |
| Supply voltage operating range (TA -20 to 85°C) | VS | 2.5 | 26 | V | –20°C 至 85°C | 6 | |
| Quiescent current | IQ | 65 | 100 | μA | VSENSE = 0mV | 6 | |
| Quiescent current over temperature range | IQ | 115 | μA | TA = –40°C 至 125°C | 6 | ||
| Specified temperature range | -40 | 125 | °C | 6 | |||
| Operating temperature range (natural convection) | TA | -40 | 125 | °C | 自然通风条件下的工作温度范围 | 5 | |
| Junction-to-ambient thermal resistance (DCK SC70) | RθJA | 227.3 | °C/W | DCK (SC70) 6 引脚 | 5 | ||
| Junction-to-case (top) thermal resistance (DCK SC70) | RθJC(top) | 79.5 | °C/W | DCK (SC70) 6 引脚 | 5 | ||
| Junction-to-board thermal resistance (DCK SC70) | RθJB | 72.1 | °C/W | DCK (SC70) 6 引脚 | 5 | ||
| Junction-to-top characterization parameter (DCK SC70) | ψJT | 3.6 | °C/W | DCK (SC70) 6 引脚 | 5 | ||
| Junction-to-board characterization parameter (DCK SC70) | ψJB | 70.4 | °C/W | DCK (SC70) 6 引脚 | 5 | ||
| Thermal resistance θJA (SC70, electrical table) | θJA | 250 | °C/W | SC70 | 7 | ||
| Common-mode input voltage (recommended) | VCM | 12 | V | 5 | |||
| Supply voltage (recommended, applied to V+) | VS | 5 | V | 施加到 V+ | 5 |
CAD (KiCad official)
- Symbol:
INA199C2DCKR - Footprint:
Package_TO_SOT_SMD:SOT-363_SC-70-6 - 3D model: SC-70-6 (KiCad packages3D, STEP)
- 3D model files:
ina199c2dckr-etched.step/ina199c2dckr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ina199c2dckr.step/ina199c2dckr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (43 pp, sha256
f48fb5be37c0cf43, retrieved 2026-09-18, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.2, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-4-6(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).