main
Download ZIP Propose a change
Made with KiCad 10.0 · needs KiCad 10.0 or later to open · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers iam-20680hp: viewers rendered from the public page · Ray
iam-20680hp-etched.glb iam-20680hp: factory component page (tier=lcsc) · Ray
iam-20680hp-etched.step iam-20680hp: factory component page (tier=lcsc) · Ray
iam-20680hp-hero.glb iam-20680hp: hero GLB from the etched model (keeps the MPN mark) · Ray
iam-20680hp-hero.overlay.json iam-20680hp: hero GLB from the etched model (keeps the MPN mark) · Ray
iam-20680hp.glb Publish 0.1.0 · Ray
iam-20680hp.kicad_mod Publish 0.1.0 · Ray
iam-20680hp.kicad_sym Publish 0.1.0 · Ray
iam-20680hp.lbr Publish 0.1.0 · Ray
iam-20680hp.step Publish 0.1.0 · Ray
package.json Publish 0.1.0 · Ray
page.json Set visibility: public · Ray
README.md Publish 0.1.0 · Ray
verification.json Verified: Published by the parts factory: tier lcsc, 16 pins · Ray

IAM-20680HP

TDK InvenSense · Attitude Sensors · LGA-16(3x3)

IAM-20680HP from TDK InvenSense, in a LGA-16(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VDDIO power_in Digital I/O supply voltage, specified from 1.71 V to 3.6 V.
2 SCL/SPC input I2C serial clock (SCL) or SPI serial clock (SPC); I2C lines are open drain with pull-up resistors (e.g. 10 kΩ) required, and input voltage is limited to -0.5 V to VDDIO + 0.5 V.
3 SDA/SDI bidirectional I2C serial data (SDA, open drain, pull-up required) or SPI serial data input (SDI); input voltage is limited to -0.5 V to VDDIO + 0.5 V.
4 SA0/SDO bidirectional I2C slave address LSB (SA0, selects b1101000 when low and b1101001 when high) or SPI serial data output (SDO).
5 CS input Chip select: 0 selects SPI mode and 1 selects I2C mode.
6 INT output Interrupt digital output, configurable as totem pole or open-drain.
7 RESV unconnected Reserved; do not connect.
8 FSYNC input Optional synchronization digital input; connect to GND if unused, with input voltage limited to -0.5 V to VDDIO + 0.5 V.
9 RESV passive Reserved; connect to GND.
10 RESV passive Reserved; connect to GND.
11 RESV passive Reserved; connect to GND.
12 RESV passive Reserved; connect to GND.
13 GND power_in Ground; connect to GND.
14 REGOUT passive Regulator filter capacitor connection; the BOM specifies a 0.47 µF X7R ±10% capacitor, and REGOUT is rated -0.5 V to 2 V.
15 RESV passive Reserved; connect to GND.
16 VDD power_in Power supply, operating range 1.71 V to 3.6 V.

Key specifications

Parameter Value
Manufacturer TDK InvenSense
Package LGA-16(3x3)
Category Sensors
Pins 16

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Nonlinearity (gyroscope) -0.1 0.1 % Best fit straight line; 25°C 9
Cross-Axis Sensitivity (gyroscope) -5 5 % 25°C 9
Initial ZRO Tolerance (gyroscope) -0.8 dps 25°C 9
ZRO Variation Over Temperature (gyroscope) -1 1 dps -40°C to +85°C 9
Gyroscope Mechanical Frequencies 25 27 29 KHz 9
Gyroscope Low Pass Filter Response Programmable Range 5 250 Hz Programmable range 9
Gyroscope Output Data Rate 4 8000 Hz Programmable, Normal (Filtered) mode 9
Nonlinearity (accelerometer) -0.25 0.25 % Best Fit Straight Line for 2g, 25°C 10
Cross-Axis Sensitivity (accelerometer) -5 5 % 25°C 10
Initial Zero-G Tolerance -50 50 mg All axes, 25°C 10
Zero-G Level Change vs. Temperature -50 50 mg -40°C to +85°C 10
Accelerometer Low Pass Filter Response Programmable Range 5 218 Hz Programmable range 10
Accelerometer Output Data Rate, Low power (duty-cycled) 0.24 500 Hz Low power (duty-cycled) 10
Accelerometer Output Data Rate, Low noise (active) 4 4000 Hz Low noise (active) 10
Supply Voltage VDD VDD 1.71 1.8 3.6 V 11
Supply Voltage VDDIO VDDIO 1.71 1.8 3.6 V 11
Specified Temperature Range -40 85 °C Performance parameters not applicable beyond Specified Temperature Range 11
Supply Ramp Time (TRAMP) TRAMP 0.01 100 ms Monotonic ramp; 10% to 90% of final value 12
Temperature Sensor Operating Range (Ambient) -40 85 °C Ambient 12
Power-On Reset Supply Ramp Time (TRAMP) TRAMP 0.01 100 ms Valid power-on RESET 12
Start-up time for register read/write 11 100 ms From power-up 12
Digital Input Capacitance (FSYNC, SA0, SPC, SDI, CS) CI 10 pF 12
VOL.INT, INT Low-Level Output Voltage VOL.INT 0.1 V OPEN=1, 0.3mA sink current 12
I2C VOL, LOW-Level Output Voltage VOL 0 0.4 V 3 mA sink current 12
I2C Output Fall Time (tof) tof 300 ns Cb bus capacitance in pF; 20+0.1Cb 12
I2C VIL, LOW Level Input Voltage VIL -0.5 V 12
Clock Frequency Initial Tolerance (gyro inactive) -5 5 % CLK_SEL=0, 6 or gyro inactive; 25°C 13
Clock Frequency Initial Tolerance (gyro active) -1 1 % CLK_SEL=1,2,3,4,5 and gyro active; 25°C 13
Clock Frequency Variation over Temperature (gyro inactive) -10 10 % CLK_SEL=0,6 or gyro inactive 13
Clock Frequency Variation over Temperature (gyro active) -1 1 % CLK_SEL=1,2,3,4,5 and gyro active 13
SPI Operating Frequency, Low Speed Characterization -10 10 % Nominal 100 kHz; all registers read/write 13
Supply Voltage, VDD (absolute maximum) VDD -0.5 4 V 16
Supply Voltage, VDDIO (absolute maximum) VDDIO -0.5 4 V 16
REGOUT (absolute maximum) REGOUT -0.5 2 V 16
Input Voltage Level (SA0, FSYNC, SCL, SDA) -0.5 V Upper limit printed as VDDIO + 0.5 V 16
Acceleration (unpowered) 10000 g Any axis, unpowered, 0.2 ms 16
Operating Temperature Range (absolute maximum) -40 85 °C 16
Storage Temperature Range -40 125 °C 16
Electrostatic Discharge (HBM) 2 kV HBM 16
Electrostatic Discharge (MM) 250 V MM 16
Latch-up -100 100 mA JEDEC Class II (2), 125°C 16
Junction-to-ambient thermal resistance θJA 84.58 °C/W Junction-to-ambient 16
Junction-to-top characterization parameter ψJT 7 °C/W Junction-to-top 16

CAD (KiCad official)

  • Symbol: IAM-20680HP
  • Footprint: Package_LGA:LGA-16_3x3mm_P0.5mm
  • 3D model: LGA-16(3x3), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.75 mm tall, datasheet A, nominal). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: iam-20680hp-etched.step / iam-20680hp-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); iam-20680hp.step / iam-20680hp.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: TDK InvenSense datasheet (52 pp, sha256 5ad58c71352bfcad, retrieved 2026-11-12, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF