main
Ray
Publish 0.1.0
3172659
HX65HVD75-S
ZHHXDZ · RS-485 / RS-422 ICs · SOP-8
HX65HVD75-S from ZHHXDZ, in a SOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RO | output | Receiver data output: when the receiver is enabled, RO goes high if V(A)-V(B) > -50 mV and low if V(A)-V(B) < -200 mV. |
| 2 | RE | input | Active-low receiver output enable: RO is valid when RE is low and the receiver is disabled when RE is high, and with RE high and DE low the chip enters shutdown (control input limits -0.3 V to +6.0 V, VIH 2.0 V min, VIL 0.8 V max). |
| 3 | DE | input | Driver output enable: driver outputs are enabled when DE is high and disabled to high-impedance when DE is low, and with RE high and DE low the chip enters shutdown (control input limits -0.3 V to +6.0 V). |
| 4 | DI | input | Driver data input: a low level forces the non-inverting output low and the inverting output high, and a high level forces the non-inverting output high and the inverting output low (driver input limits -0.3 V to +6.0 V). |
| 5 | GND | power_in | Ground reference for the device; all voltages are referenced to this pin. |
| 6 | A | bidirectional | Non-inverting bus terminal shared by the driver output and receiver input, with absolute bus voltage limits of -8.0 V to +13.0 V and ±15 kV HBM ESD protection. |
| 7 | B | bidirectional | Inverting bus terminal shared by the driver output and receiver input, with absolute bus voltage limits of -8.0 V to +13.0 V and ±15 kV HBM ESD protection. |
| 8 | Vcc | power_in | Supply voltage: absolute maximum range is 3.0 V to +6.0 V, with DC and AC characteristics specified at 3.3 V ±5%. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | ZHHXDZ |
| Package | SOP-8 |
| Category | Interface |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| 电源电压 (VCC) absolute maximum rating | VCC | 3 | 6 | V | 2 | ||
| 控制输入电压 DE, RE | DE,RE | -0.3 | 6 | V | 2 | ||
| 驱动输入电压 DI | DI | -0.3 | 6 | V | 2 | ||
| 驱动输出电压/接收输入电压 A, B | A,B | -8 | 13 | V | 2 | ||
| 存储温度范围 | TSTG | -65 | 150 | ℃ | 2 | ||
| 工作温度范围 | TOP | -40 | 125 | ℃ | 2 | ||
| 功耗 PD (SOP-8) | PD | 471 | mW | SOP-8 (+70℃以上) | 2 | ||
| 焊锡温度 (10 秒) | TL | 300 | ℃ | 10 s | 2 | ||
| 差分驱动输出(无负载) | VOD1 | 2 | V | 图 1 | 2 | ||
| 差分驱动输出 (RS-422) | VOD2 | 1.2 | V | R=50Ω(RS-422), 图 1 | 2 | ||
| 差分驱动输出 (RS-485) | VOD2 | 1.2 | V | R=27Ω(RS-485), 图 1 | 2 | ||
| 差分输出幅值变化 | ΔVOD | 0.2 | V | R=50Ω or R=27Ω, 图 1 | 2 | ||
| 驱动器输出共模电平 | VOC | 0 | 3 | V | R=50Ω or R=27Ω, 图 1 | 2 | |
| 驱动器输出共模电平变化 | ΔVOC | 0.2 | V | R=50Ω or R=27Ω, 图 1 | 2 | ||
| 输入高电平 (DE, DI, RE) | VIH1 | 2 | V | 2 | |||
| 输入低电平 (DE, DI, RE) | VIL1 | 0.8 | V | 2 | |||
| 输入电流 (DE, DI, RE) | IIN1 | -2 | 2 | uA | DE, DI, RE | 2 | |
| 输入电流(A 与 B) | IIN4 | 125 | uA | DE=GND, VCC=GND or 5.25V, VIN=12V | 2 | ||
| 输入电流(A 与 B) | IIN4 | -75 | uA | DE=GND, VCC=GND or 5.25V, VIN=-7V | 2 | ||
| 驱动器输出短路电流 (-7V≤VOUT≤VCC) | IOD1 | -100 | mA | -7V≤VOUT≤VCC | 2 | ||
| 驱动器输出短路电流 (0V≤VOUT≤12V) | IOD1 | 100 | mA | 0V≤VOUT≤12V | 2 | ||
| 驱动器输出短路电流 (0V≤VOUT≤VCC) | IOD1 | -25 | 25 | mA | 0V≤VOUT≤VCC | 2 | |
| 接收器差分输入阈值电压 | VTH | -200 | -50 | mV | -7V≤VCM≤+12V | 2 | |
| 接收器输出低电平 | VOL | 0 | 0.4 | V | IO=4mA, VID=-1V | 2 | |
| 接收器输出高阻态漏电流 | IOZR | -1 | 1 | uA | 0.4V≤VO≤2.4V | 2 | |
| 接收器输入阻抗 | RIN | 96 | KΩ | -7V≤VCM≤+12V | 2 | ||
| 接收器输出短路电流 | IOSR | -7 | 95 | mA | 0V≤VRO≤VCC | 2 | |
| 静态供电电流 (DE=VCC) | ICC | 450 | 600 | uA | No load, RE=DI=GNDorVcc, DE=VCC | 2 | |
| 静态供电电流 (DE=GND) | ICC | 450 | 600 | uA | No load, RE=DI=GNDorVcc, DE=GND | 2 | |
| 关断电流 | ISHDN | 0.1 | 10 | uA | DE=GND, RE=Vcc | 2 | |
| 静电保护 (A, B 管脚) 接触放电模型 | ESD | -12 | 12 | KV | 接触放电模型 (A, B pins) | 2 | |
| 静电保护 (A, B 管脚) 人体模型 | ESD | -15 | 15 | KV | 人体模型 (A, B pins) | 2 | |
| 静电保护 (其他管脚) 人体模型 | ESD | -4 | 4 | KV | 人体模型 (other pins) | 2 | |
| 驱动器从输出低到关断时间 | tDLZ | 500 | ns | CL=15pF,S1 关断 图 4,6 | 2 | ||
| 驱动器从输出高到关断时间 | tDHZ | 500 | ns | CL=15pF,S2 关断 图 4,6 | 2 | ||
| 驱动器输入输出延时之差 (接收器 tRSKD) | tRSKD | -50 | 10 | 50 | ns | /VID/≥2.0V;VID 上升下降时间小于 15ns 图 7,9 | 2 |
| 接收器输入输出延时 | tRPLH, tRPHL | 125 | 250 | ns | /VID/≥2.0V;VID 上升下降时间小于 15ns 图 7,9 | 2 | |
| 接收器使能到输出低 | tRZL | 20 | 120 | ns | CL=100pF,S1 关断 图 2,8 | 2 | |
| 接收器使能到输出高 | tRZH | 20 | 120 | ns | CL=100pF,S2 关断 图 2,8 | 2 | |
| 接收器从输出高到关断 | tRHZ | 20 | 120 | ns | CL=100pF,S1 关断 图 2,8 | 2 | |
| 接收器从输出低到关断 | tRLZ | 20 | 120 | ns | CL=100pF,S2 关断 图 2,8 | 2 | |
| 芯片关断时间 | tSHDN | 50 | 200 | 600 | ns | 2 | |
| 从芯片关断到驱动器使能,到输出为高电平 | tDZH(SHDN) | 4500 | ns | CL=15pF,S2 关断 图 4,6 | 2 | ||
| 从芯片关断到驱动器使能,到输出为低电平 | Tdzl(SHDN) | 4500 | ns | CL=15pF,S1 关断 图 4,6 | 2 | ||
| 从芯片关断到接收器使能,到输出为高电平 | tRZH(SHDN) | 3500 | ns | CL=100pF,S2 关断 图 2,8 | 2 | ||
| 从芯片关断到接收器使能,到输出为低电平 | tRZL(SHDN) | 3500 | ns | CL=100pF,S1 关断 图 2,8 | 2 |
CAD (KiCad official)
- Symbol:
HX65HVD75-S - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOP-8 (KiCad packages3D, STEP)
- 3D model files:
hx65hvd75-s-etched.step/hx65hvd75-s-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);hx65hvd75-s.step/hx65hvd75-s.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: ZHHXDZ datasheet (5 pp, sha256
96cce5ef3af4ea3a, retrieved 2026-10-18, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# HX65HVD75-S
**ZHHXDZ** · RS-485 / RS-422 ICs · SOP-8
HX65HVD75-S from ZHHXDZ, in a SOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RO | output | Receiver data output: when the receiver is enabled, RO goes high if V(A)-V(B) > -50 mV and low if V(A)-V(B) < -200 mV. |
| 2 | RE | input | Active-low receiver output enable: RO is valid when RE is low and the receiver is disabled when RE is high, and with RE high and DE low the chip enters shutdown (control input limits -0.3 V to +6.0 V, VIH 2.0 V min, VIL 0.8 V max). |
| 3 | DE | input | Driver output enable: driver outputs are enabled when DE is high and disabled to high-impedance when DE is low, and with RE high and DE low the chip enters shutdown (control input limits -0.3 V to +6.0 V). |
| 4 | DI | input | Driver data input: a low level forces the non-inverting output low and the inverting output high, and a high level forces the non-inverting output high and the inverting output low (driver input limits -0.3 V to +6.0 V). |
| 5 | GND | power_in | Ground reference for the device; all voltages are referenced to this pin. |
| 6 | A | bidirectional | Non-inverting bus terminal shared by the driver output and receiver input, with absolute bus voltage limits of -8.0 V to +13.0 V and ±15 kV HBM ESD protection. |
| 7 | B | bidirectional | Inverting bus terminal shared by the driver output and receiver input, with absolute bus voltage limits of -8.0 V to +13.0 V and ±15 kV HBM ESD protection. |
| 8 | Vcc | power_in | Supply voltage: absolute maximum range is 3.0 V to +6.0 V, with DC and AC characteristics specified at 3.3 V ±5%. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | ZHHXDZ |
| Package | SOP-8 |
| Category | Interface |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| 电源电压 (VCC) absolute maximum rating | VCC | 3 | | 6 | V | | 2 |
| 控制输入电压 DE, RE | DE,RE | -0.3 | | 6 | V | | 2 |
| 驱动输入电压 DI | DI | -0.3 | | 6 | V | | 2 |
| 驱动输出电压/接收输入电压 A, B | A,B | -8 | | 13 | V | | 2 |
| 存储温度范围 | TSTG | -65 | | 150 | ℃ | | 2 |
| 工作温度范围 | TOP | -40 | | 125 | ℃ | | 2 |
| 功耗 PD (SOP-8) | PD | | | 471 | mW | SOP-8 (+70℃以上) | 2 |
| 焊锡温度 (10 秒) | TL | | | 300 | ℃ | 10 s | 2 |
| 差分驱动输出(无负载) | VOD1 | 2 | | | V | 图 1 | 2 |
| 差分驱动输出 (RS-422) | VOD2 | 1.2 | | | V | R=50Ω(RS-422), 图 1 | 2 |
| 差分驱动输出 (RS-485) | VOD2 | 1.2 | | | V | R=27Ω(RS-485), 图 1 | 2 |
| 差分输出幅值变化 | ΔVOD | | | 0.2 | V | R=50Ω or R=27Ω, 图 1 | 2 |
| 驱动器输出共模电平 | VOC | 0 | | 3 | V | R=50Ω or R=27Ω, 图 1 | 2 |
| 驱动器输出共模电平变化 | ΔVOC | | | 0.2 | V | R=50Ω or R=27Ω, 图 1 | 2 |
| 输入高电平 (DE, DI, RE) | VIH1 | 2 | | | V | | 2 |
| 输入低电平 (DE, DI, RE) | VIL1 | | | 0.8 | V | | 2 |
| 输入电流 (DE, DI, RE) | IIN1 | -2 | | 2 | uA | DE, DI, RE | 2 |
| 输入电流(A 与 B) | IIN4 | | | 125 | uA | DE=GND, VCC=GND or 5.25V, VIN=12V | 2 |
| 输入电流(A 与 B) | IIN4 | -75 | | | uA | DE=GND, VCC=GND or 5.25V, VIN=-7V | 2 |
| 驱动器输出短路电流 (-7V≤VOUT≤VCC) | IOD1 | -100 | | | mA | -7V≤VOUT≤VCC | 2 |
| 驱动器输出短路电流 (0V≤VOUT≤12V) | IOD1 | | | 100 | mA | 0V≤VOUT≤12V | 2 |
| 驱动器输出短路电流 (0V≤VOUT≤VCC) | IOD1 | -25 | | 25 | mA | 0V≤VOUT≤VCC | 2 |
| 接收器差分输入阈值电压 | VTH | -200 | | -50 | mV | -7V≤VCM≤+12V | 2 |
| 接收器输出低电平 | VOL | 0 | | 0.4 | V | IO=4mA, VID=-1V | 2 |
| 接收器输出高阻态漏电流 | IOZR | -1 | | 1 | uA | 0.4V≤VO≤2.4V | 2 |
| 接收器输入阻抗 | RIN | 96 | | | KΩ | -7V≤VCM≤+12V | 2 |
| 接收器输出短路电流 | IOSR | -7 | | 95 | mA | 0V≤VRO≤VCC | 2 |
| 静态供电电流 (DE=VCC) | ICC | | 450 | 600 | uA | No load, RE=DI=GNDorVcc, DE=VCC | 2 |
| 静态供电电流 (DE=GND) | ICC | | 450 | 600 | uA | No load, RE=DI=GNDorVcc, DE=GND | 2 |
| 关断电流 | ISHDN | | 0.1 | 10 | uA | DE=GND, RE=Vcc | 2 |
| 静电保护 (A, B 管脚) 接触放电模型 | ESD | -12 | | 12 | KV | 接触放电模型 (A, B pins) | 2 |
| 静电保护 (A, B 管脚) 人体模型 | ESD | -15 | | 15 | KV | 人体模型 (A, B pins) | 2 |
| 静电保护 (其他管脚) 人体模型 | ESD | -4 | | 4 | KV | 人体模型 (other pins) | 2 |
| 驱动器从输出低到关断时间 | tDLZ | | | 500 | ns | CL=15pF,S1 关断 图 4,6 | 2 |
| 驱动器从输出高到关断时间 | tDHZ | | | 500 | ns | CL=15pF,S2 关断 图 4,6 | 2 |
| 驱动器输入输出延时之差 (接收器 tRSKD) | tRSKD | -50 | 10 | 50 | ns | /VID/≥2.0V;VID 上升下降时间小于 15ns 图 7,9 | 2 |
| 接收器输入输出延时 | tRPLH, tRPHL | 125 | | 250 | ns | /VID/≥2.0V;VID 上升下降时间小于 15ns 图 7,9 | 2 |
| 接收器使能到输出低 | tRZL | 20 | | 120 | ns | CL=100pF,S1 关断 图 2,8 | 2 |
| 接收器使能到输出高 | tRZH | 20 | | 120 | ns | CL=100pF,S2 关断 图 2,8 | 2 |
| 接收器从输出高到关断 | tRHZ | 20 | | 120 | ns | CL=100pF,S1 关断 图 2,8 | 2 |
| 接收器从输出低到关断 | tRLZ | 20 | | 120 | ns | CL=100pF,S2 关断 图 2,8 | 2 |
| 芯片关断时间 | tSHDN | 50 | 200 | 600 | ns | | 2 |
| 从芯片关断到驱动器使能,到输出为高电平 | tDZH(SHDN) | | | 4500 | ns | CL=15pF,S2 关断 图 4,6 | 2 |
| 从芯片关断到驱动器使能,到输出为低电平 | Tdzl(SHDN) | | | 4500 | ns | CL=15pF,S1 关断 图 4,6 | 2 |
| 从芯片关断到接收器使能,到输出为高电平 | tRZH(SHDN) | | | 3500 | ns | CL=100pF,S2 关断 图 2,8 | 2 |
| 从芯片关断到接收器使能,到输出为低电平 | tRZL(SHDN) | | | 3500 | ns | CL=100pF,S1 关断 图 2,8 | 2 |
## CAD (KiCad official)
- Symbol: `HX65HVD75-S`
- Footprint: `Package_SO:SOIC-8_3.9x4.9mm_P1.27mm`
- 3D model: SOP-8 (KiCad packages3D, STEP)
- 3D model files: `hx65hvd75-s-etched.step` / `hx65hvd75-s-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `hx65hvd75-s.step` / `hx65hvd75-s.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [ZHHXDZ datasheet](docs/hx65hvd75-s-datasheet.pdf) (5 pp, sha256 `96cce5ef3af4ea3a`, retrieved 2026-10-18, tier: lcsc)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/hx65hvd75-s-datasheet.pdf)