Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

HX65HVD75-S

ZHHXDZ · RS-485 / RS-422 ICs · SOP-8

HX65HVD75-S from ZHHXDZ, in a SOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 RO output Receiver data output: when the receiver is enabled, RO goes high if V(A)-V(B) > -50 mV and low if V(A)-V(B) < -200 mV.
2 RE input Active-low receiver output enable: RO is valid when RE is low and the receiver is disabled when RE is high, and with RE high and DE low the chip enters shutdown (control input limits -0.3 V to +6.0 V, VIH 2.0 V min, VIL 0.8 V max).
3 DE input Driver output enable: driver outputs are enabled when DE is high and disabled to high-impedance when DE is low, and with RE high and DE low the chip enters shutdown (control input limits -0.3 V to +6.0 V).
4 DI input Driver data input: a low level forces the non-inverting output low and the inverting output high, and a high level forces the non-inverting output high and the inverting output low (driver input limits -0.3 V to +6.0 V).
5 GND power_in Ground reference for the device; all voltages are referenced to this pin.
6 A bidirectional Non-inverting bus terminal shared by the driver output and receiver input, with absolute bus voltage limits of -8.0 V to +13.0 V and ±15 kV HBM ESD protection.
7 B bidirectional Inverting bus terminal shared by the driver output and receiver input, with absolute bus voltage limits of -8.0 V to +13.0 V and ±15 kV HBM ESD protection.
8 Vcc power_in Supply voltage: absolute maximum range is 3.0 V to +6.0 V, with DC and AC characteristics specified at 3.3 V ±5%.

Key specifications

Parameter Value
Manufacturer ZHHXDZ
Package SOP-8
Category Interface
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
电源电压 (VCC) absolute maximum rating VCC 3 6 V 2
控制输入电压 DE, RE DE,RE -0.3 6 V 2
驱动输入电压 DI DI -0.3 6 V 2
驱动输出电压/接收输入电压 A, B A,B -8 13 V 2
存储温度范围 TSTG -65 150 ℃ 2
工作温度范围 TOP -40 125 ℃ 2
功耗 PD (SOP-8) PD 471 mW SOP-8 (+70℃以上) 2
焊锡温度 (10 秒) TL 300 ℃ 10 s 2
差分驱动输出(无负载) VOD1 2 V 图 1 2
差分驱动输出 (RS-422) VOD2 1.2 V R=50Ω(RS-422), 图 1 2
差分驱动输出 (RS-485) VOD2 1.2 V R=27Ω(RS-485), 图 1 2
差分输出幅值变化 ΔVOD 0.2 V R=50Ω or R=27Ω, 图 1 2
驱动器输出共模电平 VOC 0 3 V R=50Ω or R=27Ω, 图 1 2
驱动器输出共模电平变化 ΔVOC 0.2 V R=50Ω or R=27Ω, 图 1 2
输入高电平 (DE, DI, RE) VIH1 2 V 2
输入低电平 (DE, DI, RE) VIL1 0.8 V 2
输入电流 (DE, DI, RE) IIN1 -2 2 uA DE, DI, RE 2
输入电流(A 与 B) IIN4 125 uA DE=GND, VCC=GND or 5.25V, VIN=12V 2
输入电流(A 与 B) IIN4 -75 uA DE=GND, VCC=GND or 5.25V, VIN=-7V 2
驱动器输出短路电流 (-7V≤VOUT≤VCC) IOD1 -100 mA -7V≤VOUT≤VCC 2
驱动器输出短路电流 (0V≤VOUT≤12V) IOD1 100 mA 0V≤VOUT≤12V 2
驱动器输出短路电流 (0V≤VOUT≤VCC) IOD1 -25 25 mA 0V≤VOUT≤VCC 2
接收器差分输入阈值电压 VTH -200 -50 mV -7V≤VCM≤+12V 2
接收器输出低电平 VOL 0 0.4 V IO=4mA, VID=-1V 2
接收器输出高阻态漏电流 IOZR -1 1 uA 0.4V≤VO≤2.4V 2
接收器输入阻抗 RIN 96 KΩ -7V≤VCM≤+12V 2
接收器输出短路电流 IOSR -7 95 mA 0V≤VRO≤VCC 2
静态供电电流 (DE=VCC) ICC 450 600 uA No load, RE=DI=GNDorVcc, DE=VCC 2
静态供电电流 (DE=GND) ICC 450 600 uA No load, RE=DI=GNDorVcc, DE=GND 2
关断电流 ISHDN 0.1 10 uA DE=GND, RE=Vcc 2
静电保护 (A, B 管脚) 接触放电模型 ESD -12 12 KV 接触放电模型 (A, B pins) 2
静电保护 (A, B 管脚) 人体模型 ESD -15 15 KV 人体模型 (A, B pins) 2
静电保护 (其他管脚) 人体模型 ESD -4 4 KV 人体模型 (other pins) 2
驱动器从输出低到关断时间 tDLZ 500 ns CL=15pF,S1 关断 图 4,6 2
驱动器从输出高到关断时间 tDHZ 500 ns CL=15pF,S2 关断 图 4,6 2
驱动器输入输出延时之差 (接收器 tRSKD) tRSKD -50 10 50 ns /VID/≥2.0V;VID 上升下降时间小于 15ns 图 7,9 2
接收器输入输出延时 tRPLH, tRPHL 125 250 ns /VID/≥2.0V;VID 上升下降时间小于 15ns 图 7,9 2
接收器使能到输出低 tRZL 20 120 ns CL=100pF,S1 关断 图 2,8 2
接收器使能到输出高 tRZH 20 120 ns CL=100pF,S2 关断 图 2,8 2
接收器从输出高到关断 tRHZ 20 120 ns CL=100pF,S1 关断 图 2,8 2
接收器从输出低到关断 tRLZ 20 120 ns CL=100pF,S2 关断 图 2,8 2
芯片关断时间 tSHDN 50 200 600 ns 2
从芯片关断到驱动器使能,到输出为高电平 tDZH(SHDN) 4500 ns CL=15pF,S2 关断 图 4,6 2
从芯片关断到驱动器使能,到输出为低电平 Tdzl(SHDN) 4500 ns CL=15pF,S1 关断 图 4,6 2
从芯片关断到接收器使能,到输出为高电平 tRZH(SHDN) 3500 ns CL=100pF,S2 关断 图 2,8 2
从芯片关断到接收器使能,到输出为低电平 tRZL(SHDN) 3500 ns CL=100pF,S1 关断 图 2,8 2

CAD (KiCad official)

  • Symbol: HX65HVD75-S
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SOP-8 (KiCad packages3D, STEP)
  • 3D model files: hx65hvd75-s-etched.step / hx65hvd75-s-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); hx65hvd75-s.step / hx65hvd75-s.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: ZHHXDZ datasheet (5 pp, sha256 96cce5ef3af4ea3a, retrieved 2026-10-18, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF