Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

HV9912NG-G

Microchip Tech · LED Drivers · SOIC-16

HV9912NG-G from Microchip Tech, in a SOIC-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VIN power_in Input of the 90V high-voltage linear regulator that powers the IC.
2 VDD power_out Power supply pin for all internal circuits, regulated to 7.75V typical; must be bypassed with a low-ESR capacitor of at least 0.1 µF to GND.
3 GATE output Output gate driver (+0.2A/-0.4A) for an external N-channel power MOSFET.
4 GND power_in Ground return for all low-power analog internal circuitry; must be connected to the return path from the input.
5 CS input Senses the source current of the external power FET and includes a built-in 100 ns (minimum) blanking time.
6 SC passive Sets the slope compensation (current sourced out of the pin is 0 to 100 µA).
7 RT passive Sets the frequency of the power circuit; a resistor between RT and GND programs Constant Frequency mode.
8 SYNC bidirectional I/O pin that may be connected to the SYNC pin of other HV9912 ICs, causing the oscillators to lock to the highest frequency oscillator.
9 CLIM input Programmable input current limit for the converter, set using a resistor divider from the REF pin.
10 REF power_out 2% accurate reference voltage output; must be bypassed with a 0.01 µF-0.1 µF capacitor to GND.
11 FAULT output Pulled to ground on an output short-circuit or output overvoltage condition; can drive an external MOSFET to disconnect the load from the source.
12 OVP input Overvoltage protection input: GATE turns off and FAULT goes low when the voltage exceeds 5V, and the IC turns on again when it falls below 4.5V.
13 PWMD input PWM dimming input: switching is disabled when pulled to GND or left open, and resumes when an external TTL high level is applied.
14 COMP passive Connection for the closed-loop compensation network to GND; the capacitor also controls the hiccup time.
15 IREF input The voltage at this pin sets the output current level, set using a resistor divider from the REF pin.
16 FDBK input Provides output current feedback to the IC using a current sense resistor.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package SOIC-16
Category Nixie Tube Driver/LED Driver
Pins 16

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input DC Supply Voltage Range VINDC 90 V DC input voltage (Note 2) 4
Shutdown Mode Supply Current IINSD 1.5 mA PWMD connected to GND (Note 2) 4
Internally Regulated Voltage VDD 7.25 7.75 8.25 V VIN = 9V-90V; PWMD connected to GND (Note 2) 4
VDD Undervoltage Lockout Threshold UVLORISE 6.5 7 V VDD rising 4
VDD Undervoltage Lockout Hysteresis UVLOHYST 500 mV VDD falling 4
REF Pin Voltage VREF 1.225 1.25 1.285 V REF bypassed with a 0.1 µF capacitor to GND; IREF = 0; PWMD = GND; 0°C < TA < +85°C 4
REF Pin Voltage (full temp) VREF 1.225 1.25 1.29 V REF bypassed with a 0.1 µF capacitor to GND; IREF = 0; PWMD = GND; -40°C < TA < 125°C 4
Line Regulation of Reference Voltage VREFLINE 0 20 mV REF bypassed with a 0.1 µF capacitor to GND; IREF = 0; VDD = 7.25V-12V; PWMD = GND 4
Load Regulation of Reference Voltage VREFLOAD 0 10 mV REF bypassed with a 0.1 µF capacitor to GND; IREF = 0 µA-500 µA; PWMD = GND 5
PWMD Input Low Voltage VPWMD(LO) 0.8 V Note 2 5
PWMD Input High Voltage VPWMD(HI) 2 V Note 2 5
PWMD Pull-down Resistance RPWMD 50 100 150 kΩ VPWMD = 5V 5
GATE Short-circuit Current ISOURCE 0.2 A VGATE = 0V 5
GATE Sinking Current ISINK 0.4 A VGATE = VDD 5
GATE Output Rise Time TRISE 50 85 ns CGATE = 1 nF 5
GATE Output Fall Time TFALL 25 45 ns CGATE = 1 nF 5
Overvoltage Rising Trip Point VOVP,RISING 4.75 5 5.25 V OVP rising 5
Overvoltage Hysteresis VOVP,HYST 0.5 V OVP falling 5
Leading Edge Blanking TBLANK 100 280 ns 0°C < TA < +85°C 5
Leading Edge Blanking (full temp) TBLANK 100 330 ns -40°C < TA < +125°C 5
Delay to Output of COMP Comparator TDELAY1 200 ns COMP = VDD; CLIM = REF; CSENSE = 0 mV to 600 mV (step up) 5
Delay to Output of CLIMIT Comparator TDELAY2 200 ns COMP = VDD; CLIM = 300 mV; CSENSE = 0 mV to 400 mV (step up) 5
Comparator Offset Voltage VOFFSET -10 10 mV 5
Gain Bandwidth Product GBW 1 MHz 75 pF capacitance at OP pin (Note 3) 5
Open-loop DC Gain AV 60 dB Output open 5
Input Common Mode Range VCM -0.3 3 V Note 3 5
Output Voltage Range VO 0.7 6.75 V Note 3 5
Transconductance gM 450 550 650 µA/V 5
Input Offset Voltage VOFFSET -5 5 mV 5
Input Bias Current IBIAS 0.5 1 nA Note 3 5
Oscillator Frequency fOSC1 99 106 118 kHz RT = 500 kΩ (Note 2) 5
Oscillator Frequency fOSC2 510 580 650 kHz RT = 96 kΩ (Note 2) 5
Maximum Duty Cycle DMAX 87 93 % 5
SYNC Input High VSYNCH 2 V 6
SYNC Input Low VSYNCL 0.8 V 6
SYNC Output Current IOUTSYNC 18 µA 6
Gain for Short-circuit Comparator GSC 1.9 2 2.1 V 6
Minimum Output Voltage of the Gain Stage VOMIN 0.125 0.25 V 0°C < TA < +85°C; IREF = GND 6
Minimum Output Voltage of the Gain Stage (full temp) VOMIN 0.125 0.26 V -40°C < TA < +125°C; IREF = GND 6
Propagation Time for Short-circuit Detection TOFF 250 ns PWMD = VDD; IREF = 400 mA; FDBK step from 0 mV to 900 mV; FAULT goes from high to low 6
Fault Output Rise Time TRISE,FAULT 300 ns 330 pF capacitor at FAULT pin 6
Fault Output Fall Time TFALL,FAULT 300 ns 330 pF capacitor at FAULT pin 6
Blanking Time TBLANK,SC 480 900 ns 6
Current Source at COMP Pin used for Hiccup Mode Protection IHICCUP 5 µA 6
Current Sourced Out of SC Pin ISLOPE 0 100 µA Note 2 6
Internal Current Mirror Ratio GSLOPE 1.8 2 2.26 ISLOPE = 50 µA; RSC = 1 kΩ 6
Operating Junction Temperature TJ -40 125 °C 6
Storage Temperature Ts -65 150 °C 6
Package Thermal Resistance 16-lead SOIC θJA 83 °C/W 16-lead SOIC 6
VIN to GND VIN -0.5 100 V 4
VDD to GND VDD -0.3 13.5 V 4
CS to GND CS -0.3 V max is VDD+0.3V 4
PWMD to GND PWMD -0.3 V max is VDD+0.3V 4
GATE to GND GATE -0.3 V max is VDD+0.3V 4
All Other Pins to GND -0.3 V max is VDD+0.3V 4
Continuous Power Dissipation 1200 mW TA = +25°C 4
Operating Junction Temperature Range -40 125 °C 4
Storage Temperature Range -65 150 °C 4

CAD (KiCad official)

  • Symbol: HV9912NG-G
  • Footprint: Package_SO:SOIC-16_3.9x9.9mm_P1.27mm
  • 3D model: SOIC-16 (KiCad packages3D, STEP)
  • 3D model files: hv9912ng-g-etched.step / hv9912ng-g-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); hv9912ng-g.step / hv9912ng-g.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (20 pp, sha256 95071e3a782fc328, retrieved 2026-10-23, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF