Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

HT33035ARWZ

HTCSEMI · Motor Driver ICs · SOP-24

HT33035ARWZ from HTCSEMI, in a SOP-24. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 BT output Open-collector top drive output B; sink current max 50 mA and VCE max 40 V.
2 AT output Open-collector top drive output A; sink current max 50 mA and VCE max 40 V.
3 Fwd/Rev input Forward/reverse direction select digital input, limited to Vref with a 3.0 V high threshold and 0.8 V low threshold.
4 SA input Sensor input A to the rotor position decoder, digital input limited to Vref.
5 SB input Sensor input B to the rotor position decoder, digital input limited to Vref.
6 SC input Sensor input C to the rotor position decoder, digital input limited to Vref.
7 Output Enable input Output enable input that enables or disables the drive outputs, with 3.0 V high and 0.8 V low thresholds.
8 Reference Output power_out 6.25 V temperature compensated reference output capable of supplying sensor power, with 40 mA minimum short-circuit current.
9 Current Sense Noninverting Input input Current sense noninverting input with an input voltage range of -0.3 to 5.0 V.
10 Oscillator passive Sawtooth oscillator timing pin for RT/CT, with oscillator input current max 30 mA and a typical frequency of 25 kHz.
11 Error Amp Noninverting Input input Error amplifier noninverting input with an input voltage range of -0.3 V to Vref.
12 Error Amp Inverting Input input Error amplifier inverting input with an input voltage range of -0.3 V to Vref.
13 Error Amp Out/PWM Input bidirectional Error amplifier output and PWM input, with output current (source or sink) max 10 mA.
14 Fault Output output Open-collector active-low fault output with 20 V max and 20 mA max sink current.
15 Current Sense Inverting Input input Current sense inverting input (current sense reference) with an input voltage range of -0.3 to 5.0 V.
16 Gnd power_in Ground reference for the device.
17 VCC power_in Positive power supply for the controller, operating 10 to 30 V with 40 V absolute maximum.
18 VC power_in Bottom drive supply voltage, 30 V maximum.
19 CB output High-current totem pole bottom drive output C, 100 mA max source or sink.
20 BB output High-current totem pole bottom drive output B, 100 mA max source or sink.
21 AB output High-current totem pole bottom drive output A, 100 mA max source or sink.
22 60°/120° Select input Selects 60°/300° or 120°/240° sensor phasing; digital input limited to Vref.
23 Brake input Brake input for dynamic braking; digital input limited to Vref.
24 CT output Open-collector top drive output C; sink current max 50 mA and VCE max 40 V.

Key specifications

Parameter Value
Manufacturer HTCSEMI
Package SOP-24
Category Power Supply Chip
Pins 24

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Power Supply Voltage Vcc 40 V 2
Oscillator Input Current (Source or Sink) Iosc 30 mA 2
Error Amp Input Voltage Range VIR -0.3 V Pins 11, 12, upper limit Vref 2
Error Amp Output Current IOut 10 mA Source or Sink 2
Current Sense Input Voltage Range VSense -0.3 5 V Pins 9, 15 2
Fault Output Voltage VCE(Fault) 20 V 2
Fault Output Sink Current ISink(Fault) 20 mA 2
Top Drive Voltage VCE(top) 40 V Pins 1, 2, 24 2
Top Drive Sink Current ISink(top) 50 mA Pins 1, 2, 24 2
Bottom Drive Supply Voltage VC 30 V Pin 18 2
Bottom Drive Output Current IDRV 100 mA Source or Sink, Pins 19, 20, 21 2
Power Dissipation, SO package PD 650 mW TA = 85°C 2
Thermal Resistance, Junction-to-Air, SO package RθJA 100 °C/W SO Package 2
Operating Junction Temperature TJ 150 °C 2
Reference Output Voltage Vref 5.9 6.24 6.5 V Iref = 1.0 mA, TA = 25°C 2
Reference Output Voltage Vref 5.82 6.57 V Iref = 1.0 mA, TA = -40 to +85°C 2
Line Regulation Regline 1.5 30 mV Vcc = 10 to 30 V, Iref = 1.0 mA 2
Load Regulation Regload 16 30 mV Iref = 1.0 to 20 mA 2
Output Short Circuit Current ISC 40 75 mA Note 3 2
Reference Under Voltage Lockout Threshold Vth 4 4.5 5 V 2
Input Offset Voltage VIO 0.4 10 mV TA = -40 to +85°C 2
Input Offset Current IIO 8.9 500 nA TA = -40 to +85°C 2
Input Bias Current IIB -46 -1000 nA TA = -40 to +85°C 2
Open Loop Voltage Gain AVOL 70 80 dB VO = 3.0 V, RL = 15 k 2
Input Common Mode Rejection Ratio CMRR 55 86 dB 2
Power Supply Rejection Ratio PSRR 65 105 dB Vcc = Vc = 10 to 30 V 2
Output Voltage Swing High State VOH 4.6 5.3 V RL = 15k to Gnd 3
Output Voltage Swing Low State VOL 0.5 1 V RL = 15k to Vref 3
Oscillator Frequency fosc 22 25 28 kHz 3
Frequency Change with Voltage ∆fosc/∆V 0.01 5 % Vcc = 10 to 30 V 3
Sawtooth Peak Voltage VOSC(P) 4.1 4.5 V 3
Sawtooth Valley Voltage VOSC(V) 1.2 1.5 V 3
Input Threshold Voltage High State VIH 3 2.2 V Pins 3, 4, 5, 6, 7, 22, 23 3
Input Threshold Voltage Low State VIL 1.7 0.8 V Pins 3, 4, 5, 6, 7, 22, 23 3
Top Drive Output Sink Saturation VCE(SAT) 0.5 1.5 V ISink = 25 mA 3
Top Drive Output Off-State Leakage IDRV(leak) 0.06 100 nA VCE = 30 V 3
Fault Output Sink Saturation VCE(sat) 225 500 mV Isink = 16 mA 3
Fault Output Off-State Leakage IFLT(leak) 1 100 nA VCE = 20 V 3

CAD (KiCad official)

  • Symbol: HT33035ARWZ
  • Footprint: Package_SO:SOP-24_7.5x15.4mm_P1.27mm
  • 3D model: SOP-24, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 2.65 mm nominal SOIC height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
  • 3D model files: ht33035arwz-etched.step / ht33035arwz-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ht33035arwz.step / ht33035arwz.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: HTCSEMI datasheet (4 pp, sha256 e8f208d6534f8665, retrieved 2026-10-27, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text+vision), consensus claude-opus-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF