main
Ray
Publish 0.1.0
f3081b4
HRT9013-18GB
HXY MOSFET · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · SOT-23-5L
HRT9013-18GB from HXY MOSFET, in a SOT-23-5L. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Power input for the regulator; the absolute maximum input voltage is 7 V. |
| 2 | VSS | power_in | Ground pin for the regulator. |
| 3 | CE | input | Enable input: a low level of 0 to 0.5 V (VCEL) turns the output off, and the datasheet recommends driving it to 1.1 V to allow margin; an internal 1 MΩ resistor connects CE to the GND pin. |
| 4 | NC | unconnected | No internal connection; the pin is left floating (悬空). |
| 5 | VOUT | power_out | Regulated output of the LDO; for the HRT9013-18GB variant the nominal output is 1.8 V, with a maximum output current of 500 mA. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | HXY MOSFET |
| Package | SOT-23-5L |
| Category | Power Management (PMIC) |
| Pins | 5 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Maximum output current | IOUT (max) | 500 | mA | 3 | |||
| Load regulation | ΔVOUT | 50 | mV | VIN=VOUT+1V, 1mA≤IOUT≤100mA | 3 | ||
| Line regulation | ΔVOUT/(ΔVIN•VOUT) | 0.39 | %/V | IOUT=40mA, 4.3V≤VIN≤15V | 3 | ||
| Dropout voltage | Vdrop1 | 100 | mV | VIN=4.3V, IOUT=100mA | 3 | ||
| Dropout voltage | Vdrop2 | 300 | mV | VIN=4.3V, IOUT=200mA | 3 | ||
| Quiescent current | ISS1 | 75 | μA | 3 | |||
| Shutdown current | ISS2 | 1 | μA | VIN=5V, VCE=VSS | 3 | ||
| CE input voltage high | VCEH | 0.3 | V | 3 | |||
| CE input voltage low | VCEL | 0 | 0.5 | V | 3 | ||
| CE input current | ICE | 1 | uA | 3 | |||
| Ripple rejection ratio | PSRR | 75 | dB | VIN=(VOUT+1)+1Vp-pAC, IOUT=40mA, f=1kHz | 3 | ||
| Output noise | en | 50 | uVrms | IOUT=40mA, 300Hz~50kHz | 3 | ||
| Specified output voltage | VOUT(T) | 1.8 | V | HRT9013-18GB ordering table entry | 1 | ||
| Internal resistance between CE pin and GND pin | 1 | M | built into the chip between CE pin and GND pin | 3 | |||
| Input voltage | VIN | 7 | V | 2 | |||
| Output current | IOUT | 600 | mA | 2 | |||
| Power dissipation | PD | 300 | mW | 2 | |||
| Storage temperature range | TSTG | -40 | 150 | °C | 2 | ||
| Soldering temperature | 260 | °C | 10 sec | 2 | |||
| Operating temperature range | TOPR | -40 | 80 | °C | 2 | ||
| Junction operating temperature range | -40 | 85 | °C | junction temperature | 1 |
CAD (KiCad official)
- Symbol:
HRT9013-18GB - Footprint:
Package_TO_SOT_SMD:SOT-23-5 - 3D model: SOT-23-5L, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.25 mm tall, datasheet A, midpoint of min and max). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
hrt9013-18gb-etched.step/hrt9013-18gb-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);hrt9013-18gb.step/hrt9013-18gb.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: HXY MOSFET datasheet (6 pp, sha256
7ff6786d6318b5c3, retrieved 2026-11-12, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# HRT9013-18GB
**HXY MOSFET** · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · SOT-23-5L
HRT9013-18GB from HXY MOSFET, in a SOT-23-5L. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Power input for the regulator; the absolute maximum input voltage is 7 V. |
| 2 | VSS | power_in | Ground pin for the regulator. |
| 3 | CE | input | Enable input: a low level of 0 to 0.5 V (VCEL) turns the output off, and the datasheet recommends driving it to 1.1 V to allow margin; an internal 1 MΩ resistor connects CE to the GND pin. |
| 4 | NC | unconnected | No internal connection; the pin is left floating (悬空). |
| 5 | VOUT | power_out | Regulated output of the LDO; for the HRT9013-18GB variant the nominal output is 1.8 V, with a maximum output current of 500 mA. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | HXY MOSFET |
| Package | SOT-23-5L |
| Category | Power Management (PMIC) |
| Pins | 5 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Maximum output current | IOUT (max) | | | 500 | mA | | 3 |
| Load regulation | ΔVOUT | | | 50 | mV | VIN=VOUT+1V, 1mA≤IOUT≤100mA | 3 |
| Line regulation | ΔVOUT/(ΔVIN•VOUT) | | 0.39 | | %/V | IOUT=40mA, 4.3V≤VIN≤15V | 3 |
| Dropout voltage | Vdrop1 | | | 100 | mV | VIN=4.3V, IOUT=100mA | 3 |
| Dropout voltage | Vdrop2 | | | 300 | mV | VIN=4.3V, IOUT=200mA | 3 |
| Quiescent current | ISS1 | | 75 | | μA | | 3 |
| Shutdown current | ISS2 | | | 1 | μA | VIN=5V, VCE=VSS | 3 |
| CE input voltage high | VCEH | 0.3 | | | V | | 3 |
| CE input voltage low | VCEL | 0 | | 0.5 | V | | 3 |
| CE input current | ICE | | | 1 | uA | | 3 |
| Ripple rejection ratio | PSRR | | 75 | | dB | VIN=(VOUT+1)+1Vp-pAC, IOUT=40mA, f=1kHz | 3 |
| Output noise | en | | 50 | | uVrms | IOUT=40mA, 300Hz~50kHz | 3 |
| Specified output voltage | VOUT(T) | | 1.8 | | V | HRT9013-18GB ordering table entry | 1 |
| Internal resistance between CE pin and GND pin | | | 1 | | M | built into the chip between CE pin and GND pin | 3 |
| Input voltage | VIN | | | 7 | V | | 2 |
| Output current | IOUT | | | 600 | mA | | 2 |
| Power dissipation | PD | | | 300 | mW | | 2 |
| Storage temperature range | TSTG | -40 | | 150 | °C | | 2 |
| Soldering temperature | | | | 260 | °C | 10 sec | 2 |
| Operating temperature range | TOPR | -40 | | 80 | °C | | 2 |
| Junction operating temperature range | | -40 | | 85 | °C | junction temperature | 1 |
## CAD (KiCad official)
- Symbol: `HRT9013-18GB`
- Footprint: `Package_TO_SOT_SMD:SOT-23-5`
- 3D model: SOT-23-5L, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.25 mm tall, datasheet A, midpoint of min and max). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files: `hrt9013-18gb-etched.step` / `hrt9013-18gb-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `hrt9013-18gb.step` / `hrt9013-18gb.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [HXY MOSFET datasheet](docs/hrt9013-18gb-datasheet.pdf) (6 pp, sha256 `7ff6786d6318b5c3`, retrieved 2026-11-12, tier: lcsc)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/hrt9013-18gb-datasheet.pdf)