main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers hrt9013-18gb: viewers rendered from the public page · Ray
hrt9013-18gb-etched.glb hrt9013-18gb: factory component page (tier=lcsc) · Ray
hrt9013-18gb-etched.step hrt9013-18gb: factory component page (tier=lcsc) · Ray
hrt9013-18gb-hero.glb hrt9013-18gb: hero GLB from the etched model (keeps the MPN mark) · Ray
hrt9013-18gb-hero.overlay.json hrt9013-18gb: hero GLB from the etched model (keeps the MPN mark) · Ray
hrt9013-18gb.glb Publish 0.1.0 · Ray
hrt9013-18gb.kicad_mod Publish 0.1.0 · Ray
hrt9013-18gb.kicad_sym Publish 0.1.0 · Ray
hrt9013-18gb.lbr Publish 0.1.0 · Ray
hrt9013-18gb.step Publish 0.1.0 · Ray
package.json Publish 0.1.0 · Ray
page.json Set visibility: public · Ray
README.md Publish 0.1.0 · Ray
verification.json Verified: Published by the parts factory: tier lcsc, 5 pins · Ray

HRT9013-18GB

HXY MOSFET · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · SOT-23-5L

HRT9013-18GB from HXY MOSFET, in a SOT-23-5L. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VIN power_in Power input for the regulator; the absolute maximum input voltage is 7 V.
2 VSS power_in Ground pin for the regulator.
3 CE input Enable input: a low level of 0 to 0.5 V (VCEL) turns the output off, and the datasheet recommends driving it to 1.1 V to allow margin; an internal 1 MΩ resistor connects CE to the GND pin.
4 NC unconnected No internal connection; the pin is left floating (悬空).
5 VOUT power_out Regulated output of the LDO; for the HRT9013-18GB variant the nominal output is 1.8 V, with a maximum output current of 500 mA.

Key specifications

Parameter Value
Manufacturer HXY MOSFET
Package SOT-23-5L
Category Power Management (PMIC)
Pins 5

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Maximum output current IOUT (max) 500 mA 3
Load regulation ΔVOUT 50 mV VIN=VOUT+1V, 1mA≤IOUT≤100mA 3
Line regulation ΔVOUT/(ΔVIN•VOUT) 0.39 %/V IOUT=40mA, 4.3V≤VIN≤15V 3
Dropout voltage Vdrop1 100 mV VIN=4.3V, IOUT=100mA 3
Dropout voltage Vdrop2 300 mV VIN=4.3V, IOUT=200mA 3
Quiescent current ISS1 75 μA 3
Shutdown current ISS2 1 μA VIN=5V, VCE=VSS 3
CE input voltage high VCEH 0.3 V 3
CE input voltage low VCEL 0 0.5 V 3
CE input current ICE 1 uA 3
Ripple rejection ratio PSRR 75 dB VIN=(VOUT+1)+1Vp-pAC, IOUT=40mA, f=1kHz 3
Output noise en 50 uVrms IOUT=40mA, 300Hz~50kHz 3
Specified output voltage VOUT(T) 1.8 V HRT9013-18GB ordering table entry 1
Internal resistance between CE pin and GND pin 1 M built into the chip between CE pin and GND pin 3
Input voltage VIN 7 V 2
Output current IOUT 600 mA 2
Power dissipation PD 300 mW 2
Storage temperature range TSTG -40 150 °C 2
Soldering temperature 260 °C 10 sec 2
Operating temperature range TOPR -40 80 °C 2
Junction operating temperature range -40 85 °C junction temperature 1

CAD (KiCad official)

  • Symbol: HRT9013-18GB
  • Footprint: Package_TO_SOT_SMD:SOT-23-5
  • 3D model: SOT-23-5L, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.25 mm tall, datasheet A, midpoint of min and max). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: hrt9013-18gb-etched.step / hrt9013-18gb-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); hrt9013-18gb.step / hrt9013-18gb.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: HXY MOSFET datasheet (6 pp, sha256 7ff6786d6318b5c3, retrieved 2026-11-12, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF