main
History Download
Ray Publish 0.1.0 41f8ea1

HR1000AGS-Z

Monolithic Power Systems · AC-DC Controllers & Regulators · SOIC-16

HR1000AGS-Z from Monolithic Power Systems, in a SOIC-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SS passive Soft-start pin: a capacitor to GND and a resistor to Fset set the maximum oscillator frequency and the start-up frequency shift, and an internal switch discharges the capacitor when the chip turns off.
2 TIMER passive Sets the period between over-current and shutdown: the IC stops switching when the pin voltage exceeds 3.5V and resumes when it drops below 0.3V.
3 CT passive Time-set pin: an internal current source programmed by the network on pin 4 charges and discharges the capacitor on this pin to GND and determines the switching frequency.
4 Fset passive Provides a precise 2V reference; the resistor to GND sets the minimum oscillator frequency, the opto-coupler connects here for feedback, and the maximum source current is 2mA.
5 Burst input Burst-mode threshold compared with an internal 1.25V reference: the IC enters an idle state below it and resumes when the voltage exceeds the reference by 50mV; tie to Fset if burst-mode is not used.
6 CS input Primary-current sense: above a 0.8V threshold (50mV hysteresis) the frequency increases, and above 1.5V a comparator latches the device off; tie to GND if the function is not used.
7 BO input Brown-out input sensing the high-voltage bus: below 1.25V the IC shuts down without latching, and the pin is limited to -0.3 to 6V as an analog input; bias between 1.25V and 5.5V if unused.
8 LATCH input IC latch input: when the pin voltage exceeds 1.85V the IC shuts down and latches, with the latch cleared when VCC falls below the UVLO threshold; tie to GND if unused.
9 PFC output Interface to the front-end PFC controller: normally high, it goes low on shutdown conditions, and its maximum voltage is VCC with sink current self-limited when pin low.
10 GND power_in Ground: current return for the low-side gate-driver current and the IC bias current, to be kept separate from any pulsed current return.
11 LG output Low-side gate driver with minimum 0.5A source and minimum 1A sink-peak current to drive the lower MOSFET; the pin is actively pulled to GND during UVLO and its maximum voltage is 16V.
12 VCC power_in IC supply voltage with recommended operating range of 13V to 15.5V; supply current is limited to below 25mA and the pin is self-limited.
13 N.C. unconnected High-voltage spacer that is not internally connected, provided to meet creepage-distance safety requirements on the PCB.
14 SW power_in High-side switch source and current return for the high-side gate drive; VSW is limited to -3V to VBST-18V, dVSW/dt to 50 V/ns, and layout must avoid large spikes below ground.
15 HG output High-side floating gate driver with minimum 0.5A source and minimum 1A sink-peak current to drive the upper MOSFET, with an internal resistor to SW keeping the pin defined during UVLO.
16 BST power_in High-side floating supply: connect a bootstrap capacitor between BST and SW, fed by an internal bootstrap diode; the floating supply voltage is limited to -1 to 618V.

Key specifications

Parameter Value
Manufacturer Monolithic Power Systems
Package SOIC-16
Category Power Management
Pins 16

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Floating supply voltage (pin 16) VBST -1 618 V 3
Floating ground voltage (pin 14) VSW -3 V 3
Floating ground max. slew rate (pin 14) dVSW/dt 50 V/ns 3
Maximum voltage (pin 9) VPFC -0.3 V pin open 3
Maximum source current (pin 4) IFset 2 mA 3
Maximum voltage (pin 11) LG -0.3 16 V 3
Analog inputs and outputs (pins 1 to 8) -0.3 6 V 3
Continuous power dissipation PIC 1.56 W TA = +25°C 3
Junction temperature TJ 150 °C 3
Lead temperature (solder) TLead 260 °C 3
Storage temperature TStorage -55 150 °C 3
Supply voltage VCC 13 15.5 V 3
Analog inputs and outputs -0.3 6.5 V 3
Operating junction temperature TJ -40 125 °C 3
VCC high threshold, IC switch-on VCCH 10.3 11 11.7 V 4
VCC low threshold, IC switch-off VCCL 7.5 8.2 8.9 V 4
VCC operating range 8.9 15.5 V 4
Start-up current Istart-up 250 300 µA Before the device turns on, VCC=VCCH-0.2V 4
Quiescent current Iq 1.5 2 mA Device on, VBurst=1V 4
Operating current Iop 3 5 mA Device on, VBurst=VFset 4
Residual consumption Ir 350 400 µA VCC>16V or VCC<8V, VLATCH>1.85V or VCS>1.5V or VTIMER>3.5V or VBO<1.25V or VBO>5.5V or OTP 4
Frequency shift threshold VCSx 0.75 0.8 0.85 V 4
Latch-off threshold VCSlatch 1.41 1.5 1.59 V 4
Line voltage sensing (BO) threshold voltage Vth 1.2 1.25 1.3 V 4
Line voltage sensing (BO) clamp level Vclamp 5.1 5.5 5.8 V 4
Line voltage sensing (BO) current hysteresis IHyst 9 12 15 µA VCC>5V, VBO=0.3V 4
LATCH threshold Vth 1.75 1.85 1.95 V 4
Output duty cycle D 48 50 52 % 4
Dead-time tD 300 350 400 ns 4
Voltage reference at Fset pin VREF 1.92 2 2.08 V 4
Standby disable threshold Vth 1.18 1.23 1.28 V 4
Delayed shutdown charge current ICHARGE 80 130 180 µA VTIMER=1V, VCS=0.85V 5
Threshold for forced operation at maximum frequency Vth1 1.88 2 2.08 V 5
Shut down threshold Vth2 3.3 3.5 3.7 V 5
Restart threshold Vth3 0.25 0.3 0.35 V 5
Hysteresis (VCC) Vhys 2.5 V 4
VCC clamp current during fault condition IClamp 6 mA VCC=16V, Latch=2V 4
VCC clamp voltage during fault condition VClamp 15.3 V VCC>16V or VLATCH>1.85V or VCS>1.5V or VTIMER>3.5V or VBO<1.25V or VBO>5.5V or OTP 4
Input bias current (CS) ICS 1 µA VCS=0 to VCSlatch 4
Leading-edge blanking tLEB 250 ns 4
Input bias current (LATCH) ILATCH 1 µA VLATCH=0 to Vth 4
Oscillation frequency fosc 600 kHz 4
CT peak value VCFp 3.8 V 4
CT valley value VCFv 0.9 V 4
Low saturation level (PFC) VL 0.2 V IPFC=1mA, VLATCH=2V 4
Discharge resistance (SS) R 120 Ω VCS>VCSx 4
Standby hysteresis Vhys 100 mV 4
Thermal shutdown threshold 150 °C 5
Thermal shutdown recovery threshold 120 °C 5
Low-side gate driver peak source current (LG) Isourcepk 1.5 A 5
Low-side gate driver peak sink current (LG) Isinkpk 2 A 5
Low-side gate driver sourcing resistor (LG) Rsource 4 Ω 5
Low-side gate driver sinking resistor (LG) Rsink 2 Ω 5
UVLO saturation 1.1 V VCC=0 to VCCH, Isink=2mA 5
High-side gate driver peak source current (HG) Isourcepk 1.5 A 5
High-side gate driver peak sink current (HG) Isinkpk 2 A 5
High-side gate driver sourcing resistor (HG) Rsource 4 Ω 5
High-side gate driver sinking resistor (HG) Rsink 2 Ω 5
Thermal resistance junction-to-case, SOIC16 θJC 35 °C/W Measured on JESD51-7, 4-layer PCB 3

CAD (KiCad official)

  • Symbol: HR1000AGS-Z
  • Footprint: Package_SO:SOIC-16_3.9x9.9mm_P1.27mm
  • 3D model: SOIC-16 (KiCad packages3D, STEP)
  • 3D model files: hr1000ags-z-etched.step / hr1000ags-z-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); hr1000ags-z.step / hr1000ags-z.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Monolithic Power Systems datasheet (24 pp, sha256 d0b70055e24157a5, retrieved 2026-11-05, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF