Generated by kicad-footprint-generator · KiCad file format 20260206
HR1000AGS-Z
Monolithic Power Systems · AC-DC Controllers & Regulators · SOIC-16
HR1000AGS-Z from Monolithic Power Systems, in a SOIC-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SS | passive | Soft-start pin: a capacitor to GND and a resistor to Fset set the maximum oscillator frequency and the start-up frequency shift, and an internal switch discharges the capacitor when the chip turns off. |
| 2 | TIMER | passive | Sets the period between over-current and shutdown: the IC stops switching when the pin voltage exceeds 3.5V and resumes when it drops below 0.3V. |
| 3 | CT | passive | Time-set pin: an internal current source programmed by the network on pin 4 charges and discharges the capacitor on this pin to GND and determines the switching frequency. |
| 4 | Fset | passive | Provides a precise 2V reference; the resistor to GND sets the minimum oscillator frequency, the opto-coupler connects here for feedback, and the maximum source current is 2mA. |
| 5 | Burst | input | Burst-mode threshold compared with an internal 1.25V reference: the IC enters an idle state below it and resumes when the voltage exceeds the reference by 50mV; tie to Fset if burst-mode is not used. |
| 6 | CS | input | Primary-current sense: above a 0.8V threshold (50mV hysteresis) the frequency increases, and above 1.5V a comparator latches the device off; tie to GND if the function is not used. |
| 7 | BO | input | Brown-out input sensing the high-voltage bus: below 1.25V the IC shuts down without latching, and the pin is limited to -0.3 to 6V as an analog input; bias between 1.25V and 5.5V if unused. |
| 8 | LATCH | input | IC latch input: when the pin voltage exceeds 1.85V the IC shuts down and latches, with the latch cleared when VCC falls below the UVLO threshold; tie to GND if unused. |
| 9 | PFC | output | Interface to the front-end PFC controller: normally high, it goes low on shutdown conditions, and its maximum voltage is VCC with sink current self-limited when pin low. |
| 10 | GND | power_in | Ground: current return for the low-side gate-driver current and the IC bias current, to be kept separate from any pulsed current return. |
| 11 | LG | output | Low-side gate driver with minimum 0.5A source and minimum 1A sink-peak current to drive the lower MOSFET; the pin is actively pulled to GND during UVLO and its maximum voltage is 16V. |
| 12 | VCC | power_in | IC supply voltage with recommended operating range of 13V to 15.5V; supply current is limited to below 25mA and the pin is self-limited. |
| 13 | N.C. | unconnected | High-voltage spacer that is not internally connected, provided to meet creepage-distance safety requirements on the PCB. |
| 14 | SW | power_in | High-side switch source and current return for the high-side gate drive; VSW is limited to -3V to VBST-18V, dVSW/dt to 50 V/ns, and layout must avoid large spikes below ground. |
| 15 | HG | output | High-side floating gate driver with minimum 0.5A source and minimum 1A sink-peak current to drive the upper MOSFET, with an internal resistor to SW keeping the pin defined during UVLO. |
| 16 | BST | power_in | High-side floating supply: connect a bootstrap capacitor between BST and SW, fed by an internal bootstrap diode; the floating supply voltage is limited to -1 to 618V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | SOIC-16 |
| Category | Power Management |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Floating supply voltage (pin 16) | VBST | -1 | 618 | V | 3 | ||
| Floating ground voltage (pin 14) | VSW | -3 | V | 3 | |||
| Floating ground max. slew rate (pin 14) | dVSW/dt | 50 | V/ns | 3 | |||
| Maximum voltage (pin 9) | VPFC | -0.3 | V | pin open | 3 | ||
| Maximum source current (pin 4) | IFset | 2 | mA | 3 | |||
| Maximum voltage (pin 11) | LG | -0.3 | 16 | V | 3 | ||
| Analog inputs and outputs (pins 1 to 8) | -0.3 | 6 | V | 3 | |||
| Continuous power dissipation | PIC | 1.56 | W | TA = +25°C | 3 | ||
| Junction temperature | TJ | 150 | °C | 3 | |||
| Lead temperature (solder) | TLead | 260 | °C | 3 | |||
| Storage temperature | TStorage | -55 | 150 | °C | 3 | ||
| Supply voltage | VCC | 13 | 15.5 | V | 3 | ||
| Analog inputs and outputs | -0.3 | 6.5 | V | 3 | |||
| Operating junction temperature | TJ | -40 | 125 | °C | 3 | ||
| VCC high threshold, IC switch-on | VCCH | 10.3 | 11 | 11.7 | V | 4 | |
| VCC low threshold, IC switch-off | VCCL | 7.5 | 8.2 | 8.9 | V | 4 | |
| VCC operating range | 8.9 | 15.5 | V | 4 | |||
| Start-up current | Istart-up | 250 | 300 | µA | Before the device turns on, VCC=VCCH-0.2V | 4 | |
| Quiescent current | Iq | 1.5 | 2 | mA | Device on, VBurst=1V | 4 | |
| Operating current | Iop | 3 | 5 | mA | Device on, VBurst=VFset | 4 | |
| Residual consumption | Ir | 350 | 400 | µA | VCC>16V or VCC<8V, VLATCH>1.85V or VCS>1.5V or VTIMER>3.5V or VBO<1.25V or VBO>5.5V or OTP | 4 | |
| Frequency shift threshold | VCSx | 0.75 | 0.8 | 0.85 | V | 4 | |
| Latch-off threshold | VCSlatch | 1.41 | 1.5 | 1.59 | V | 4 | |
| Line voltage sensing (BO) threshold voltage | Vth | 1.2 | 1.25 | 1.3 | V | 4 | |
| Line voltage sensing (BO) clamp level | Vclamp | 5.1 | 5.5 | 5.8 | V | 4 | |
| Line voltage sensing (BO) current hysteresis | IHyst | 9 | 12 | 15 | µA | VCC>5V, VBO=0.3V | 4 |
| LATCH threshold | Vth | 1.75 | 1.85 | 1.95 | V | 4 | |
| Output duty cycle | D | 48 | 50 | 52 | % | 4 | |
| Dead-time | tD | 300 | 350 | 400 | ns | 4 | |
| Voltage reference at Fset pin | VREF | 1.92 | 2 | 2.08 | V | 4 | |
| Standby disable threshold | Vth | 1.18 | 1.23 | 1.28 | V | 4 | |
| Delayed shutdown charge current | ICHARGE | 80 | 130 | 180 | µA | VTIMER=1V, VCS=0.85V | 5 |
| Threshold for forced operation at maximum frequency | Vth1 | 1.88 | 2 | 2.08 | V | 5 | |
| Shut down threshold | Vth2 | 3.3 | 3.5 | 3.7 | V | 5 | |
| Restart threshold | Vth3 | 0.25 | 0.3 | 0.35 | V | 5 | |
| Hysteresis (VCC) | Vhys | 2.5 | V | 4 | |||
| VCC clamp current during fault condition | IClamp | 6 | mA | VCC=16V, Latch=2V | 4 | ||
| VCC clamp voltage during fault condition | VClamp | 15.3 | V | VCC>16V or VLATCH>1.85V or VCS>1.5V or VTIMER>3.5V or VBO<1.25V or VBO>5.5V or OTP | 4 | ||
| Input bias current (CS) | ICS | 1 | µA | VCS=0 to VCSlatch | 4 | ||
| Leading-edge blanking | tLEB | 250 | ns | 4 | |||
| Input bias current (LATCH) | ILATCH | 1 | µA | VLATCH=0 to Vth | 4 | ||
| Oscillation frequency | fosc | 600 | kHz | 4 | |||
| CT peak value | VCFp | 3.8 | V | 4 | |||
| CT valley value | VCFv | 0.9 | V | 4 | |||
| Low saturation level (PFC) | VL | 0.2 | V | IPFC=1mA, VLATCH=2V | 4 | ||
| Discharge resistance (SS) | R | 120 | Ω | VCS>VCSx | 4 | ||
| Standby hysteresis | Vhys | 100 | mV | 4 | |||
| Thermal shutdown threshold | 150 | °C | 5 | ||||
| Thermal shutdown recovery threshold | 120 | °C | 5 | ||||
| Low-side gate driver peak source current (LG) | Isourcepk | 1.5 | A | 5 | |||
| Low-side gate driver peak sink current (LG) | Isinkpk | 2 | A | 5 | |||
| Low-side gate driver sourcing resistor (LG) | Rsource | 4 | Ω | 5 | |||
| Low-side gate driver sinking resistor (LG) | Rsink | 2 | Ω | 5 | |||
| UVLO saturation | 1.1 | V | VCC=0 to VCCH, Isink=2mA | 5 | |||
| High-side gate driver peak source current (HG) | Isourcepk | 1.5 | A | 5 | |||
| High-side gate driver peak sink current (HG) | Isinkpk | 2 | A | 5 | |||
| High-side gate driver sourcing resistor (HG) | Rsource | 4 | Ω | 5 | |||
| High-side gate driver sinking resistor (HG) | Rsink | 2 | Ω | 5 | |||
| Thermal resistance junction-to-case, SOIC16 | θJC | 35 | °C/W | Measured on JESD51-7, 4-layer PCB | 3 |
CAD (KiCad official)
- Symbol:
HR1000AGS-Z - Footprint:
Package_SO:SOIC-16_3.9x9.9mm_P1.27mm - 3D model: SOIC-16 (KiCad packages3D, STEP)
- 3D model files:
hr1000ags-z-etched.step/hr1000ags-z-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);hr1000ags-z.step/hr1000ags-z.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Monolithic Power Systems datasheet (24 pp, sha256
d0b70055e24157a5, retrieved 2026-11-05, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).