main
History Download
Ray Publish 0.1.0 4957600

Hi5000H

Hichips(智芯) · IC · HTSSOP-16

Hi5000H from Hichips(智芯), in a HTSSOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 CLPF passive Reference filter capacitor pin (datasheet table prints it as CPLF; Fig. 5.2 and the QFN table use CLPF), placed close to the pin and its GND return per the PCB notes.
2 COMP passive Loop compensation pin; the application circuit uses an RC network (e.g. 20K + 10nF in parallel with 100pF) connected here.
3 VDD power_out Internal regulated supply, clamped at about 5.8 V; a bypass capacitor of 1.0 µF or more must be placed right beside the pin, sized up for larger gate-drive MOSFETs.
4 LD input Analog dimming input accepting 0.2 V to 2.5 V (chip enabled above 200 mV, off below 100 mV), with an internal pull-up so it may be left floating; a capacitor to GND sets the soft-start time.
5 DIM input PWM-to-analog dimming and low-standby enable input with internal pull-up; a low level longer than 80 ms puts the chip into standby below 80 uA, and the input may be left floating.
6 NC unconnected No internal connection; leave floating.
7 CS input Cycle-by-cycle peak current-limit sense input referenced to the sense resistor to GND, rated for -0.3 V to 60 V and limited to about 340 mV.
8 GND power_in Internal chip ground, which is also tied to the exposed pad (EP); keep single-point connection to the CS sense resistor GND and the VDD/CLPF capacitor grounds.
9 GATE output Gate drive output for the external power NMOS, with pull-up current of about 400 mA and pull-down current of about 600 mA; rated -0.3 V to 60 V.
10 NC unconnected No internal connection; leave floating.
11 VIN power_in High-voltage supply input for the chip (6.5 V to 75 V operating range, absolute maximum -0.3 V to 80 V); a sensitive node to keep away from switching nodes.
12 ISENSEP input Positive input of the output-current sense resistor, rated -0.3 V to 80 V absolute maximum; a sensitive node to keep away from switching nodes.
13 ISENSEN input Negative input of the output-current sense resistor, rated -0.3 V to 80 V absolute maximum; output current is set as 0.251 V divided by the sense resistor.
14 UVLO input Input undervoltage-protection set pin with internal pull-up; the GATE output turns off below 1.1 V and restarts above 1.2 V (0.1 V hysteresis).
15 PWM input PWM dimming input with internal pull-up (high when floating), thresholds 1.2 V rising and 0.8 V falling, able to respond to pulses shorter than 60 ns.
16 VFB input Output overvoltage-protection sense input with internal pull-down (may be left floating); GATE turns off above 1.2 V and restarts below 1.1 V (0.1 V hysteresis).
17 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Hichips(智芯)
Package HTSSOP-16
Category
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
休眠待机电流 (ISTANDBY) ISTANDBY 80 uA 7
VIN电压范围 VIN 6.5 75 V 7
UVLO 欠压保护范围 UVLO 3 6 V 7
逐周期限流电压 VCS 340 mV VIN=6.5V 7
PWM转模拟调光阈值上限 VDIM_H 1.2 V PWM rising 7
PWM转模拟调光阈值下限 VDIM_L 0.8 V PWM falling 7
PWM调光检测阈值上限 VPWM_H 1.2 V PWM rising 7
PWM调光检测阈值下限 VPWM_L 0.8 V PWM falling 7
模拟调光低到高调光电压范围 VLD 0.22 2.5 V 7
模拟调光高到低调光电压范围 VLD 2.5 0.1 V 7
输出过压保护 VOVP 1.1 1.2 V 7
输入欠压保护 VUVLO 1.1 1.2 V 7
外部供电输入 (VIN) 极限 VIN -0.3 80 V 3
输出电流检测正极 (ISENSEP) 极限 ISENSEP -0.3 80 V 3
输出电流检测负极 (ISENSEN) 极限 ISENSEN -0.3 80 V 3
CS、GATE管脚耐压 CS/GATE -0.3 60 V 3
其余管脚 VDD、UVLO、VFB、LD、COMP、CLPF、DIM、PWM 极限 -0.3 6 V 3
存储温度 TSTG -40 150 ℃ 3
工作温度 TA -40 130 ℃ 3
ESD 人体放电模式 (HBM) ESD 2 KV HBM; printed as >2 KV 3

CAD (KiCad official)

  • Symbol: Hi5000H
  • Footprint: Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm
  • 3D model: HTSSOP-16 (KiCad packages3D, STEP)
  • 3D model files: hi5000h-etched.step / hi5000h-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); hi5000h.step / hi5000h.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Hichips(智芯) datasheet (16 pp, sha256 2ef53dfb27cd8d54, retrieved 2026-10-31, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF