3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownHi5000H
Hichips(智芯) · IC · HTSSOP-16
Hi5000H from Hichips(智芯), in a HTSSOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CLPF | passive | Reference filter capacitor pin (datasheet table prints it as CPLF; Fig. 5.2 and the QFN table use CLPF), placed close to the pin and its GND return per the PCB notes. |
| 2 | COMP | passive | Loop compensation pin; the application circuit uses an RC network (e.g. 20K + 10nF in parallel with 100pF) connected here. |
| 3 | VDD | power_out | Internal regulated supply, clamped at about 5.8 V; a bypass capacitor of 1.0 µF or more must be placed right beside the pin, sized up for larger gate-drive MOSFETs. |
| 4 | LD | input | Analog dimming input accepting 0.2 V to 2.5 V (chip enabled above 200 mV, off below 100 mV), with an internal pull-up so it may be left floating; a capacitor to GND sets the soft-start time. |
| 5 | DIM | input | PWM-to-analog dimming and low-standby enable input with internal pull-up; a low level longer than 80 ms puts the chip into standby below 80 uA, and the input may be left floating. |
| 6 | NC | unconnected | No internal connection; leave floating. |
| 7 | CS | input | Cycle-by-cycle peak current-limit sense input referenced to the sense resistor to GND, rated for -0.3 V to 60 V and limited to about 340 mV. |
| 8 | GND | power_in | Internal chip ground, which is also tied to the exposed pad (EP); keep single-point connection to the CS sense resistor GND and the VDD/CLPF capacitor grounds. |
| 9 | GATE | output | Gate drive output for the external power NMOS, with pull-up current of about 400 mA and pull-down current of about 600 mA; rated -0.3 V to 60 V. |
| 10 | NC | unconnected | No internal connection; leave floating. |
| 11 | VIN | power_in | High-voltage supply input for the chip (6.5 V to 75 V operating range, absolute maximum -0.3 V to 80 V); a sensitive node to keep away from switching nodes. |
| 12 | ISENSEP | input | Positive input of the output-current sense resistor, rated -0.3 V to 80 V absolute maximum; a sensitive node to keep away from switching nodes. |
| 13 | ISENSEN | input | Negative input of the output-current sense resistor, rated -0.3 V to 80 V absolute maximum; output current is set as 0.251 V divided by the sense resistor. |
| 14 | UVLO | input | Input undervoltage-protection set pin with internal pull-up; the GATE output turns off below 1.1 V and restarts above 1.2 V (0.1 V hysteresis). |
| 15 | PWM | input | PWM dimming input with internal pull-up (high when floating), thresholds 1.2 V rising and 0.8 V falling, able to respond to pulses shorter than 60 ns. |
| 16 | VFB | input | Output overvoltage-protection sense input with internal pull-down (may be left floating); GATE turns off above 1.2 V and restarts below 1.1 V (0.1 V hysteresis). |
| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Hichips(智芯) |
| Package | HTSSOP-16 |
| Category | |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| 休眠待机电流 (ISTANDBY) | ISTANDBY | 80 | uA | 7 | |||
| VIN电压范围 | VIN | 6.5 | 75 | V | 7 | ||
| UVLO 欠压保护范围 | UVLO | 3 | 6 | V | 7 | ||
| 逐周期限流电压 | VCS | 340 | mV | VIN=6.5V | 7 | ||
| PWM转模拟调光阈值上限 | VDIM_H | 1.2 | V | PWM rising | 7 | ||
| PWM转模拟调光阈值下限 | VDIM_L | 0.8 | V | PWM falling | 7 | ||
| PWM调光检测阈值上限 | VPWM_H | 1.2 | V | PWM rising | 7 | ||
| PWM调光检测阈值下限 | VPWM_L | 0.8 | V | PWM falling | 7 | ||
| 模拟调光低到高调光电压范围 | VLD | 0.22 | 2.5 | V | 7 | ||
| 模拟调光高到低调光电压范围 | VLD | 2.5 | 0.1 | V | 7 | ||
| 输出过压保护 | VOVP | 1.1 | 1.2 | V | 7 | ||
| 输入欠压保护 | VUVLO | 1.1 | 1.2 | V | 7 | ||
| 外部供电输入 (VIN) 极限 | VIN | -0.3 | 80 | V | 3 | ||
| 输出电流检测正极 (ISENSEP) 极限 | ISENSEP | -0.3 | 80 | V | 3 | ||
| 输出电流检测负极 (ISENSEN) 极限 | ISENSEN | -0.3 | 80 | V | 3 | ||
| CS、GATE管脚耐压 | CS/GATE | -0.3 | 60 | V | 3 | ||
| 其余管脚 VDD、UVLO、VFB、LD、COMP、CLPF、DIM、PWM 极限 | -0.3 | 6 | V | 3 | |||
| 存储温度 | TSTG | -40 | 150 | ℃ | 3 | ||
| 工作温度 | TA | -40 | 130 | ℃ | 3 | ||
| ESD 人体放电模式 (HBM) | ESD | 2 | KV | HBM; printed as >2 KV | 3 |
CAD (KiCad official)
- Symbol:
Hi5000H - Footprint:
Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm - 3D model: HTSSOP-16 (KiCad packages3D, STEP)
- 3D model files:
hi5000h-etched.step/hi5000h-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);hi5000h.step/hi5000h.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Hichips(智芯) datasheet (16 pp, sha256
2ef53dfb27cd8d54, retrieved 2026-10-31, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).