main
Ray
Publish 0.1.0
32d77b3
HGA82C250M
HGSEMI · CAN Transceivers · SOP-8
HGA82C250M from HGSEMI, in a SOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | TXD | input | Transmitter data input: a low level drives the bus dominant (CANH high, CANL low) and a high or floating level makes it recessive; the MCU-side port is rated -0.3 V to VCC+0.3 V. |
| 2 | GND | power_in | Ground reference for the device; all voltages in the datasheet are referenced to this pin. |
| 3 | VCC | power_in | Supply voltage input, 4.5 V to 5.5 V recommended, with an absolute maximum of -0.3 V to +7 V. |
| 4 | RXD | output | Receiver data output that goes low when the bus is dominant, with VOH of at least 0.8VCC at -100 µA and VOL of at most 0.2VCC at 1 mA. |
| 5 | VREF | power_out | Reference voltage output of 0.45VCC to 0.55VCC when |
| 6 | CANL | bidirectional | Low-level CAN bus line input/output that withstands -36 V to +36 V, with a short-circuit current of at most 200 mA at V6 = +36 V. |
| 7 | CANH | bidirectional | High-level CAN bus line input/output that withstands -36 V to +36 V, with a short-circuit current of -100 mA to -200 mA at V7 = -36 V. |
| 8 | Rs | input | Mode/slope control input: tie to GND for high-speed mode, use a resistor to GND for slope control (0.4VCC to 0.6VCC), and drive above 0.75VCC for low-power standby. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | HGSEMI |
| Package | SOP-8 |
| Category | Interface |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | Vcc | 4.5 | 5.5 | V | 3 | ||
| CANH, CANL input/output voltage | Vcan | -36 | 36 | V | 3 | ||
| Bus differential voltage | Vdiff | 1.5 | 3 | V | 3 | ||
| Ambient temperature | Tamb | -40 | 125 | ℃ | 3 | ||
| Supply voltage | VCC | -0.3 | 7 | V | 2 | ||
| CANL, CANH bus-side input voltage | -36 | 36 | V | 2 | |||
| Pin 6,7 transient voltage | Vtr | -200 | 200 | V | see Figure 7 | 2 | |
| Storage temperature | -55 | 150 | ℃ | 2 | |||
| Ambient temperature | -40 | 125 | ℃ | 2 | |||
| Lead soldering temperature | TLEAD | 245 | ℃ | 10 s | 2 | ||
| Continuous power dissipation | 400 | mW | SOP8 | 2 | |||
| High-level input current | VIH | -200 | 30 | uA | V1=4V | 3 | |
| Low-level input current | VIL | -600 | -100 | uA | V1=1V | 3 | |
| Low-level input voltage | VIL | -0.3 | V | input recessive | 3 | ||
| Recessive bus voltage | V6,7 | 2 | 3 | V | V1=4V, no load | 3 | |
| Off-state output leakage current | ILO | -2 | 2 | mA | -2V<(V6,V7)<-7V | 3 | |
| Off-state output leakage current | ILO | -10 | 10 | mA | -5V<(V6,V7)<36V | 3 | |
| CANH output voltage | V7 | 3 | 4.5 | V | V1=1V, VCC=4.75~5.5V | 3 | |
| CANH output voltage | V7 | 2.75 | 4.5 | V | V1=1V, VCC=4.75~5.5V | 3 | |
| CANL output voltage | V6 | 0.5 | 2 | V | V1=1V | 3 | |
| Differential output voltage | ΔV6,7 | 1.5 | 3 | V | V1=1V | 3 | |
| Differential output voltage | ΔV6,7 | -500 | 50 | mV | V1=4V, no load | 3 | |
| CANH short-circuit current | Isc7 | -200 | -100 | mA | V7=-36V | 3 | |
| Recessive differential input voltage | Vdiff(r) | -1 | 0.5 | V | NOTE1 | 4 | |
| Recessive differential input voltage | Vdiff(r) | -1 | 0.4 | V | -7V<(V6,V7)<12V; NOTE1 | 4 | |
| Dominant differential input voltage | Vdiff(d) | 0.9 | 5 | V | -7V<(V6,V7)<12V | 4 | |
| Dominant differential input voltage | Vdiff(d) | 1 | 5 | V | -7V<(V6,V7)<12V, non-standby mode | 4 | |
| Dominant differential input voltage | Vdiff(d) | 0.97 | 5 | V | standby mode | 4 | |
| Dominant differential input voltage | Vdiff(d) | 0.91 | 5 | V | VCC=4.5~5.1V, standby mode | 4 | |
| VOL low-level output voltage, Pin 4 | VOL | 0 | V | I4=1mA | 4 | ||
| VOL low-level output voltage, Pin 4 | VOL | 0 | 1.5 | V | I4=10mA | 4 | |
| CANH, CANL input impedance | Ri | 5 | 25 | KΩ | 4 | ||
| Differential input impedance | Rdiff | 20 | 100 | KΩ | 4 | ||
| TXD to bus inactive delay | toffTXD | 40 | 80 | ns | R8=0Ω | 5 | |
| TXD to receiver active delay | tonRXD | 55 | 120 | ns | R8=0Ω | 5 | |
| TXD to receiver inactive delay | toffRXD | 100 | 190 | ns | R8=0Ω | 5 | |
| TXD to receiver inactive delay | toffRXD | 300 | 400 | ns | R8=47KΩ | 5 | |
| Standby mode input voltage slope-control current | Islope | -200 | -10 | uA | 5 | ||
| Supply current, dominant | I3 | 78 | mA | dominant; V1=1V; VCC<5.1V | 5 | ||
| Supply current, dominant | I3 | 80 | mA | dominant; V1=1V; VCC<5.25V | 5 | ||
| Supply current, dominant | I3 | 85 | mA | dominant; V1=1V; VCC<5.5V | 5 | ||
| Supply current, recessive | I3 | 10 | mA | recessive; V1=4V; R8=47kΩ | 5 | ||
| Supply current, standby | I3 | 275 | uA | standby mode; NOTE2 | 5 | ||
| Supply current, standby | Icc | 275 | uA | standby mode | 3 | ||
| Maximum transmission rate | 1/tbit | 1 | Mbaud | NRZ code | 3 | ||
| Minimum bit time | tbit | 1 | us | R8=0Ω | 5 | ||
| TXD to bus active delay | tonTXD | 50 | ns | R8=0Ω | 5 | ||
| CANH, CANL slew rate | /SR/ | 7 | V/us | R8=47KΩ | 5 | ||
| Wake-up delay from standby via pin 8 | twake | 20 | us | see Figure 5 | 5 | ||
| Bus dominant to RXD low delay in standby | tdRXDL | 3 | us | V8=4V; see Figure 6 | 5 | ||
| Differential input hysteresis | Vdiff(hys) | 150 | mV | see Figure 4 | 4 | ||
| Differential output voltage | ΔV6,7 | 1.5 | V | V1=1V, RL=45Ω | 3 | ||
| CANL short-circuit current | Isc6 | 200 | mA | V6=+36V | 3 |
CAD (KiCad official)
- Symbol:
HGA82C250M - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOP-8 (KiCad packages3D, STEP)
- 3D model files:
hga82c250m-etched.step/hga82c250m-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);hga82c250m.step/hga82c250m.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: HGSEMI datasheet (12 pp, sha256
cdda93dd2508e837, retrieved 2026-10-19, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# HGA82C250M
**HGSEMI** · CAN Transceivers · SOP-8
HGA82C250M from HGSEMI, in a SOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | TXD | input | Transmitter data input: a low level drives the bus dominant (CANH high, CANL low) and a high or floating level makes it recessive; the MCU-side port is rated -0.3 V to VCC+0.3 V. |
| 2 | GND | power_in | Ground reference for the device; all voltages in the datasheet are referenced to this pin. |
| 3 | VCC | power_in | Supply voltage input, 4.5 V to 5.5 V recommended, with an absolute maximum of -0.3 V to +7 V. |
| 4 | RXD | output | Receiver data output that goes low when the bus is dominant, with VOH of at least 0.8VCC at -100 µA and VOL of at most 0.2VCC at 1 mA. |
| 5 | VREF | power_out | Reference voltage output of 0.45VCC to 0.55VCC when |I5| is below 50 µA. |
| 6 | CANL | bidirectional | Low-level CAN bus line input/output that withstands -36 V to +36 V, with a short-circuit current of at most 200 mA at V6 = +36 V. |
| 7 | CANH | bidirectional | High-level CAN bus line input/output that withstands -36 V to +36 V, with a short-circuit current of -100 mA to -200 mA at V7 = -36 V. |
| 8 | Rs | input | Mode/slope control input: tie to GND for high-speed mode, use a resistor to GND for slope control (0.4VCC to 0.6VCC), and drive above 0.75VCC for low-power standby. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | HGSEMI |
| Package | SOP-8 |
| Category | Interface |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | Vcc | 4.5 | | 5.5 | V | | 3 |
| CANH, CANL input/output voltage | Vcan | -36 | | 36 | V | | 3 |
| Bus differential voltage | Vdiff | 1.5 | | 3 | V | | 3 |
| Ambient temperature | Tamb | -40 | | 125 | ℃ | | 3 |
| Supply voltage | VCC | -0.3 | | 7 | V | | 2 |
| CANL, CANH bus-side input voltage | | -36 | | 36 | V | | 2 |
| Pin 6,7 transient voltage | Vtr | -200 | | 200 | V | see Figure 7 | 2 |
| Storage temperature | | -55 | | 150 | ℃ | | 2 |
| Ambient temperature | | -40 | | 125 | ℃ | | 2 |
| Lead soldering temperature | TLEAD | | | 245 | ℃ | 10 s | 2 |
| Continuous power dissipation | | | | 400 | mW | SOP8 | 2 |
| High-level input current | VIH | -200 | | 30 | uA | V1=4V | 3 |
| Low-level input current | VIL | -600 | | -100 | uA | V1=1V | 3 |
| Low-level input voltage | VIL | -0.3 | | | V | input recessive | 3 |
| Recessive bus voltage | V6,7 | 2 | | 3 | V | V1=4V, no load | 3 |
| Off-state output leakage current | ILO | -2 | | 2 | mA | -2V<(V6,V7)<-7V | 3 |
| Off-state output leakage current | ILO | -10 | | 10 | mA | -5V<(V6,V7)<36V | 3 |
| CANH output voltage | V7 | 3 | | 4.5 | V | V1=1V, VCC=4.75~5.5V | 3 |
| CANH output voltage | V7 | 2.75 | | 4.5 | V | V1=1V, VCC=4.75~5.5V | 3 |
| CANL output voltage | V6 | 0.5 | | 2 | V | V1=1V | 3 |
| Differential output voltage | ΔV6,7 | 1.5 | | 3 | V | V1=1V | 3 |
| Differential output voltage | ΔV6,7 | -500 | | 50 | mV | V1=4V, no load | 3 |
| CANH short-circuit current | Isc7 | -200 | | -100 | mA | V7=-36V | 3 |
| Recessive differential input voltage | Vdiff(r) | -1 | | 0.5 | V | NOTE1 | 4 |
| Recessive differential input voltage | Vdiff(r) | -1 | | 0.4 | V | -7V<(V6,V7)<12V; NOTE1 | 4 |
| Dominant differential input voltage | Vdiff(d) | 0.9 | | 5 | V | -7V<(V6,V7)<12V | 4 |
| Dominant differential input voltage | Vdiff(d) | 1 | | 5 | V | -7V<(V6,V7)<12V, non-standby mode | 4 |
| Dominant differential input voltage | Vdiff(d) | 0.97 | | 5 | V | standby mode | 4 |
| Dominant differential input voltage | Vdiff(d) | 0.91 | | 5 | V | VCC=4.5~5.1V, standby mode | 4 |
| VOL low-level output voltage, Pin 4 | VOL | 0 | | | V | I4=1mA | 4 |
| VOL low-level output voltage, Pin 4 | VOL | 0 | | 1.5 | V | I4=10mA | 4 |
| CANH, CANL input impedance | Ri | 5 | | 25 | KΩ | | 4 |
| Differential input impedance | Rdiff | 20 | | 100 | KΩ | | 4 |
| TXD to bus inactive delay | toffTXD | 40 | | 80 | ns | R8=0Ω | 5 |
| TXD to receiver active delay | tonRXD | 55 | | 120 | ns | R8=0Ω | 5 |
| TXD to receiver inactive delay | toffRXD | 100 | | 190 | ns | R8=0Ω | 5 |
| TXD to receiver inactive delay | toffRXD | 300 | | 400 | ns | R8=47KΩ | 5 |
| Standby mode input voltage slope-control current | Islope | -200 | | -10 | uA | | 5 |
| Supply current, dominant | I3 | | 78 | | mA | dominant; V1=1V; VCC<5.1V | 5 |
| Supply current, dominant | I3 | | 80 | | mA | dominant; V1=1V; VCC<5.25V | 5 |
| Supply current, dominant | I3 | | 85 | | mA | dominant; V1=1V; VCC<5.5V | 5 |
| Supply current, recessive | I3 | | 10 | | mA | recessive; V1=4V; R8=47kΩ | 5 |
| Supply current, standby | I3 | | 275 | | uA | standby mode; NOTE2 | 5 |
| Supply current, standby | Icc | | 275 | | uA | standby mode | 3 |
| Maximum transmission rate | 1/tbit | | 1 | | Mbaud | NRZ code | 3 |
| Minimum bit time | tbit | | 1 | | us | R8=0Ω | 5 |
| TXD to bus active delay | tonTXD | | 50 | | ns | R8=0Ω | 5 |
| CANH, CANL slew rate | /SR/ | | 7 | | V/us | R8=47KΩ | 5 |
| Wake-up delay from standby via pin 8 | twake | | 20 | | us | see Figure 5 | 5 |
| Bus dominant to RXD low delay in standby | tdRXDL | | 3 | | us | V8=4V; see Figure 6 | 5 |
| Differential input hysteresis | Vdiff(hys) | | 150 | | mV | see Figure 4 | 4 |
| Differential output voltage | ΔV6,7 | | 1.5 | | V | V1=1V, RL=45Ω | 3 |
| CANL short-circuit current | Isc6 | | 200 | | mA | V6=+36V | 3 |
## CAD (KiCad official)
- Symbol: `HGA82C250M`
- Footprint: `Package_SO:SOIC-8_3.9x4.9mm_P1.27mm`
- 3D model: SOP-8 (KiCad packages3D, STEP)
- 3D model files: `hga82c250m-etched.step` / `hga82c250m-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `hga82c250m.step` / `hga82c250m.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [HGSEMI datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8603515460092637184) (12 pp, sha256 `cdda93dd2508e837`, retrieved 2026-10-19, tier: lcsc)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/hga82c250m-datasheet.pdf)