main
Ray
Publish 0.1.0
5fdb8bc
HD3SS3220IRNHR
Texas Instruments · USB Converters · WQFN-30-EP(2.5x4.5)
HD3SS3220IRNHR from Texas Instruments, in a WQFN-30-EP(2.5x4.5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table, the footprint is an Adom_Gen land derived from the manufacturer drawing, and the 3D model is generated to fit it.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CC2 | bidirectional | Type-C Configuration channel signal 2 that the CC logic monitors for pull-up or pull-down resistances to detect attach, port role and cable orientation. |
| 2 | CC1 | bidirectional | Type-C Configuration channel signal 1 that the CC logic monitors for pull-up or pull-down resistances to detect attach, port role and cable orientation. |
| 3 | CURRENT_MODE | input | Tri-level input that selects the advertised Type-C current in DFP or DRP-as-DFP GPIO mode: L for 900 mA default, M (500K to VDD5) for 1.5 A, and H (10K to VDD5) for 3 A. |
| 4 | PORT | input | Tri-level input sampled when ENn_CC is asserted low and VDD5 is active to select DFP (pull-up to VDD5), DRP (unconnected) or UFP (pull-down to GND) mode. |
| 5 | VBUS_DET | input | 5 V to 28 V VBUS input for UFP attachment detection, requiring one external 900 kΩ resistor between system VBUS and this pin. |
| 6 | TXp | bidirectional | Host/device USB SuperSpeed differential TX positive signal of the 2:1 mux. |
| 7 | TXn | bidirectional | Host/device USB SuperSpeed differential TX negative signal of the 2:1 mux. |
| 8 | VCC33 | power_in | 3.3 V power supply input for the device. |
| 9 | RXp | bidirectional | Host/device USB SuperSpeed differential RX positive signal of the 2:1 mux. |
| 10 | RXn | bidirectional | Host/device USB SuperSpeed differential RX negative signal of the 2:1 mux. |
| 11 | DIR | output | Open-drain Type-C plug orientation output that requires a pull-up resistor of about 200 kΩ for proper operation. |
| 12 | ENn_MUX | input | Active-low MUX enable where low selects normal operation and high selects shutdown. |
| 13 | GND | power_in | Ground reference for the device. |
| 14 | RX1n | bidirectional | Type-C port USB SuperSpeed differential RX1 negative signal. |
| 15 | RX1p | bidirectional | Type-C port USB SuperSpeed differential RX1 positive signal. |
| 16 | TX1n | bidirectional | Type-C port USB SuperSpeed differential TX1 negative signal. |
| 17 | TX1p | bidirectional | Type-C port USB SuperSpeed differential TX1 positive signal. |
| 18 | RX2n | bidirectional | Type-C port USB SuperSpeed differential RX2 negative signal. |
| 19 | RX2p | bidirectional | Type-C port USB SuperSpeed differential RX2 positive signal. |
| 20 | TX2n | bidirectional | Type-C port USB SuperSpeed differential TX2 negative signal. |
| 21 | TX2p | bidirectional | Type-C port USB SuperSpeed differential TX2 positive signal. |
| 22 | ADDR | input | Tri-level input selecting I2C address 0x67 when tied high to VDD5, GPIO mode when left unconnected, or I2C address 0x47 when tied low to GND. |
| 23 | INT_N/OUT3 | output | Dual-function open-drain output that is an active-low I2C interrupt (INT_N) in I2C mode and an audio accessory detect output (OUT3, low when detected) in GPIO mode; it is a no connect on HD3SS3220L. |
| 24 | VCONN_FAULT_N | output | Open-drain output asserted low when a VCONN overcurrent condition is detected. |
| 25 | SDA/OUT1 | bidirectional | Dual-function pin that is the I2C data signal when I2C is enabled and an open-drain UFP current-mode output (high for default 900 mA, low for 1.5 A or 3 A) in GPIO mode. |
| 26 | SCL/OUT2 | bidirectional | Dual-function pin that is the I2C clock signal when I2C is enabled and an open-drain UFP current-mode output (high for default or 1.5 A, low for 3 A) in GPIO mode. |
| 27 | ID | output | Open-drain output asserted low when a device attachment is detected on the CC pins while the port acts as a source (DFP) or as a DRP acting as DFP. |
| 28 | GND | power_in | Ground reference for the device. |
| 29 | ENn_CC | input | Active-low enable for the CC controller. |
| 30 | VDD5 | power_in | 5 V power supply input for the device. |
| 31 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WQFN-30-EP(2.5x4.5) |
| Category | Interface |
| Pins | 31 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| 5V Supply Voltage | VDD5 | -0.3 | 6 | V | 5 | ||
| 3.3V Supply Voltage | VCC33 | -0.3 | 4 | V | 5 | ||
| CC pins voltage | CC1, CC2 | -0.3 | 6 | V | 5 | ||
| VBUS_DET voltage | VBUS_DET | -0.3 | 4 | V | 5 | ||
| Super-speed differential signal pins | -0.3 | 2.5 | V | [RX/TX][p/n], [RX/TX][2/1][p/n] | 5 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 5 | ||
| 5V Supply Voltage range | VDD5 | 4.5 | 5.5 | V | 5 | ||
| 3.3V Supply Voltage range | VCC33 | 3 | 3.6 | V | 5 | ||
| Supply range for I2C (SDA, SCL) pins | VDD | 1.65 | 3.6 | V | 5 | ||
| VDD5 supply ramp time | VDD5(ramp) | 25 | ms | 5 | |||
| High speed signal pins differential voltage | V(diff) | 0 | 1.8 | VPP | 5 | ||
| High speed signal pins common mode voltage | V(cm) | 0 | 2 | V | 5 | ||
| Operating free-air/ambient temperature | TA | -40 | 85 | °C | HD3SS3220I | 5 | |
| System V(BUS) input voltage through 900K resistor | V(BUS) | 4 | 5 | 28 | V | through 900K resistor | 5 |
| Bulk capacitance on VCONN | C(BULK) | 10 | 200 | µF | Only when VCONN is on; placed on VDD5 | 5 | |
| External resistor on VBUS_DET pin | R(VBUS) | 880 | 900 | 910 | KΩ | 6 | |
| Pulldown resistor in dead-battery mode | R(CC_DB) | 4.1 | 5.1 | 6.1 | kΩ | 6 | |
| Pulldown resistor in UFP or DRP mode | R(CC_D) | 4.6 | 5.1 | 5.6 | kΩ | 6 | |
| Voltage level for detecting a DFP attach as UFP, default current | V(UFP_CC_USB) | 0.25 | 0.61 | V | DFP advertising default current source capability | 6 | |
| Voltage level for detecting a DFP attach as UFP, medium current | V(UFP_CC_MED) | 0.7 | 1.16 | V | DFP advertising medium (1.5A) current source capability | 6 | |
| Voltage level for detecting a DFP attach as UFP, high current | V(UFP_CC_HIGH) | 1.31 | 2.04 | V | DFP advertising high (3A) current source capability | 6 | |
| Voltage level for detecting a UFP attach as DFP, default current | V(DFP_CC_USB) | 1.51 | 1.6 | 1.64 | V | configured as DFP advertising default current | 6 |
| Voltage level for detecting a UFP attach as DFP, 1.5A | V(DFP_CC_MED) | 1.51 | 1.6 | 1.64 | V | configured as DFP advertising 1.5A | 6 |
| Voltage level for detecting a UFP attach as DFP, 3A | V(DFP_CC_HIGH) | 2.46 | 2.6 | 2.74 | V | configured as DFP advertising 3A | 6 |
| Voltage level for detecting an active cable attach as DFP, default current | V(AC_CC_USB) | 0.15 | 0.2 | 0.25 | V | configured as DFP advertising default current | 6 |
| Voltage level for detecting an active cable attach as DFP, 1.5A | V(AC_CC_MED) | 0.35 | 0.4 | 0.45 | V | configured as DFP advertising 1.5A | 6 |
| Voltage level for detecting an active cable attach as DFP, 3A | V(DFP_CC_HIGH) | 0.75 | 0.8 | 0.84 | V | active cable attach, configured as DFP advertising 3A | 7 |
| Default mode pull-up current source (DFP or DRP) | ICC(DEFAULT_P) | 64 | 80 | 96 | µA | 7 | |
| Medium (1.5A) mode pull-up current source (DFP or DRP) | ICC(MED_P) | 166 | 180 | 194 | µA | 7 | |
| High (3A) mode pull-up current source (DFP or DRP) | ICC(HIGH_P) | 34 | 330 | 356 | µA | as printed | 7 |
| Low-level input current | IIL | -10 | 10 | µA | 7 | ||
| Current leakage on ID pin | IID(LKG) | 10 | µA | VDD5 = 0V, ID = 5V | 7 | ||
| High-level input current (ENn_MUX) | IIH | -1 | 1 | µA | ENn_MUX input | 7 | |
| Low-level input current (ENn_MUX) | IIL | -1 | 1 | µA | ENn_MUX input | 7 | |
| Low-level signal output voltage (open drain) | VOL | 0.4 | V | OUT1, OUT2, INT_N/OUT3, ID, VCONN_FAULT_N, DIR; IOL = -1.6mA | 7 | ||
| High-level input voltage (I2C SDA/OUT1, SCL/OUT2) | VIH | 1.05 | V | I2C pins operating from 1.8/3.3V (±10%) | 7 | ||
| VBUS threshold range | V(BUS_THR) | 2.95 | 3.3 | 3.8 | V | VBUS_DET IO pin | 7 |
| External resistor between VBUS and VBUS_DET pin | RVBUS | 855 | 887 | 920 | KΩ | 7 | |
| VCONN current limit | I(VCONN) | 225 | 300 | 375 | mA | VCONN disconnected above this value | 7 |
| Current consumption in active mode, both CC controller and SS mux on | I(ACTIVE) | 0.7 | 0.9 | mA | ENn_CC/Mux = L | 6 | |
| Current consumption in shutdown mode | I(SHUTDOWN) | 5 | µA | ENn_CC/Mux = H | 6 | ||
| Data setup time | tSU:DAT | 100 | ns | I2C (SDA, SCL) | 8 | ||
| Data setup time (as printed) | tHD:DAT | 10 | ns | I2C (SDA, SCL) | 8 | ||
| Set-up time, SCL to start condition | tSU;STA | 0.6 | µs | I2C (SDA, SCL) | 8 | ||
| Data valid time | tVD;DAT | 0.9 | µs | I2C (SDA, SCL) | 8 | ||
| Bus free time between a STOP and START condition | tBUF | 1.3 | µs | I2C (SDA, SCL) | 8 | ||
| Rise time of both SDA and SCL signals | tr | 300 | ns | I2C (SDA, SCL) | 8 | ||
| Fall time of both SDA and SCL signals | tf | 300 | ns | I2C (SDA, SCL) | 8 | ||
| Total capacitive load for each bus line at ≤100KHz | CBUS_100KHZ | 400 | pF | operating at ≤100KHz | 8 | ||
| Total capacitive load for each bus line at 400KHz | CBUS_400KHZ | 100 | pF | operating at 400KHz | 8 | ||
| SCL clock frequency; I2C mode for local I2C control | fSCL | 400 | ns | as printed (unit ns) | 8 | ||
| Switching time DIR-to-Switch ON | tSW_ON | 0.5 | µs | See Figure 5-2 | 8 | ||
| Switching time DIR-to-Switch OFF | tSW_OFF | 0.5 | µs | See Figure 5-2 | 8 | ||
| ENn_CC high after both VDD5 and VCC33 stable | tENnCC_HI | 2 | ms | Refer to Figure 6-3 | 8 | ||
| VDD5 stable before VCC33 | tVDD5V_PG | 2 | ms | Refer to Figure 6-2 | 8 | ||
| Data valid acknowledge time | tVD;ACK | 0.9 | µs | I2C (SDA, SCL) | 8 | ||
| Junction-to-ambient thermal resistance | RθJA | 60.9 | °C/W | RNH (VQFN), 30 pins | 6 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 50.4 | °C/W | RNH (VQFN), 30 pins | 6 | ||
| Junction-to-board thermal resistance | RθJB | 22.8 | °C/W | RNH (VQFN), 30 pins | 6 |
CAD (Adom-generated)
- Symbol:
HD3SS3220IRNHR - Footprint:
Adom_Gen:Texas_Instruments_HD3_af6467 - 3D model: generated to fit the land (STEP)
- 3D model files:
hd3ss3220irnhr-etched.step/hd3ss3220irnhr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);hd3ss3220irnhr.step/hd3ss3220irnhr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (48 pp, sha256
44ad645ff24f1bf2, retrieved 2026-11-17, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing; 3D model generated to fit that land.
# HD3SS3220IRNHR
**Texas Instruments** · USB Converters · WQFN-30-EP(2.5x4.5)
HD3SS3220IRNHR from Texas Instruments, in a WQFN-30-EP(2.5x4.5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table, the footprint is an Adom_Gen land derived from the manufacturer drawing, and the 3D model is generated to fit it.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CC2 | bidirectional | Type-C Configuration channel signal 2 that the CC logic monitors for pull-up or pull-down resistances to detect attach, port role and cable orientation. |
| 2 | CC1 | bidirectional | Type-C Configuration channel signal 1 that the CC logic monitors for pull-up or pull-down resistances to detect attach, port role and cable orientation. |
| 3 | CURRENT_MODE | input | Tri-level input that selects the advertised Type-C current in DFP or DRP-as-DFP GPIO mode: L for 900 mA default, M (500K to VDD5) for 1.5 A, and H (10K to VDD5) for 3 A. |
| 4 | PORT | input | Tri-level input sampled when ENn_CC is asserted low and VDD5 is active to select DFP (pull-up to VDD5), DRP (unconnected) or UFP (pull-down to GND) mode. |
| 5 | VBUS_DET | input | 5 V to 28 V VBUS input for UFP attachment detection, requiring one external 900 kΩ resistor between system VBUS and this pin. |
| 6 | TXp | bidirectional | Host/device USB SuperSpeed differential TX positive signal of the 2:1 mux. |
| 7 | TXn | bidirectional | Host/device USB SuperSpeed differential TX negative signal of the 2:1 mux. |
| 8 | VCC33 | power_in | 3.3 V power supply input for the device. |
| 9 | RXp | bidirectional | Host/device USB SuperSpeed differential RX positive signal of the 2:1 mux. |
| 10 | RXn | bidirectional | Host/device USB SuperSpeed differential RX negative signal of the 2:1 mux. |
| 11 | DIR | output | Open-drain Type-C plug orientation output that requires a pull-up resistor of about 200 kΩ for proper operation. |
| 12 | ENn_MUX | input | Active-low MUX enable where low selects normal operation and high selects shutdown. |
| 13 | GND | power_in | Ground reference for the device. |
| 14 | RX1n | bidirectional | Type-C port USB SuperSpeed differential RX1 negative signal. |
| 15 | RX1p | bidirectional | Type-C port USB SuperSpeed differential RX1 positive signal. |
| 16 | TX1n | bidirectional | Type-C port USB SuperSpeed differential TX1 negative signal. |
| 17 | TX1p | bidirectional | Type-C port USB SuperSpeed differential TX1 positive signal. |
| 18 | RX2n | bidirectional | Type-C port USB SuperSpeed differential RX2 negative signal. |
| 19 | RX2p | bidirectional | Type-C port USB SuperSpeed differential RX2 positive signal. |
| 20 | TX2n | bidirectional | Type-C port USB SuperSpeed differential TX2 negative signal. |
| 21 | TX2p | bidirectional | Type-C port USB SuperSpeed differential TX2 positive signal. |
| 22 | ADDR | input | Tri-level input selecting I2C address 0x67 when tied high to VDD5, GPIO mode when left unconnected, or I2C address 0x47 when tied low to GND. |
| 23 | INT_N/OUT3 | output | Dual-function open-drain output that is an active-low I2C interrupt (INT_N) in I2C mode and an audio accessory detect output (OUT3, low when detected) in GPIO mode; it is a no connect on HD3SS3220L. |
| 24 | VCONN_FAULT_N | output | Open-drain output asserted low when a VCONN overcurrent condition is detected. |
| 25 | SDA/OUT1 | bidirectional | Dual-function pin that is the I2C data signal when I2C is enabled and an open-drain UFP current-mode output (high for default 900 mA, low for 1.5 A or 3 A) in GPIO mode. |
| 26 | SCL/OUT2 | bidirectional | Dual-function pin that is the I2C clock signal when I2C is enabled and an open-drain UFP current-mode output (high for default or 1.5 A, low for 3 A) in GPIO mode. |
| 27 | ID | output | Open-drain output asserted low when a device attachment is detected on the CC pins while the port acts as a source (DFP) or as a DRP acting as DFP. |
| 28 | GND | power_in | Ground reference for the device. |
| 29 | ENn_CC | input | Active-low enable for the CC controller. |
| 30 | VDD5 | power_in | 5 V power supply input for the device. |
| 31 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WQFN-30-EP(2.5x4.5) |
| Category | Interface |
| Pins | 31 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| 5V Supply Voltage | VDD5 | -0.3 | | 6 | V | | 5 |
| 3.3V Supply Voltage | VCC33 | -0.3 | | 4 | V | | 5 |
| CC pins voltage | CC1, CC2 | -0.3 | | 6 | V | | 5 |
| VBUS_DET voltage | VBUS_DET | -0.3 | | 4 | V | | 5 |
| Super-speed differential signal pins | | -0.3 | | 2.5 | V | [RX/TX][p/n], [RX/TX][2/1][p/n] | 5 |
| Storage temperature | Tstg | -65 | | 150 | °C | | 5 |
| 5V Supply Voltage range | VDD5 | 4.5 | | 5.5 | V | | 5 |
| 3.3V Supply Voltage range | VCC33 | 3 | | 3.6 | V | | 5 |
| Supply range for I2C (SDA, SCL) pins | VDD | 1.65 | | 3.6 | V | | 5 |
| VDD5 supply ramp time | VDD5(ramp) | 25 | | | ms | | 5 |
| High speed signal pins differential voltage | V(diff) | 0 | | 1.8 | VPP | | 5 |
| High speed signal pins common mode voltage | V(cm) | 0 | | 2 | V | | 5 |
| Operating free-air/ambient temperature | TA | -40 | | 85 | °C | HD3SS3220I | 5 |
| System V(BUS) input voltage through 900K resistor | V(BUS) | 4 | 5 | 28 | V | through 900K resistor | 5 |
| Bulk capacitance on VCONN | C(BULK) | 10 | | 200 | µF | Only when VCONN is on; placed on VDD5 | 5 |
| External resistor on VBUS_DET pin | R(VBUS) | 880 | 900 | 910 | KΩ | | 6 |
| Pulldown resistor in dead-battery mode | R(CC_DB) | 4.1 | 5.1 | 6.1 | kΩ | | 6 |
| Pulldown resistor in UFP or DRP mode | R(CC_D) | 4.6 | 5.1 | 5.6 | kΩ | | 6 |
| Voltage level for detecting a DFP attach as UFP, default current | V(UFP_CC_USB) | 0.25 | | 0.61 | V | DFP advertising default current source capability | 6 |
| Voltage level for detecting a DFP attach as UFP, medium current | V(UFP_CC_MED) | 0.7 | | 1.16 | V | DFP advertising medium (1.5A) current source capability | 6 |
| Voltage level for detecting a DFP attach as UFP, high current | V(UFP_CC_HIGH) | 1.31 | | 2.04 | V | DFP advertising high (3A) current source capability | 6 |
| Voltage level for detecting a UFP attach as DFP, default current | V(DFP_CC_USB) | 1.51 | 1.6 | 1.64 | V | configured as DFP advertising default current | 6 |
| Voltage level for detecting a UFP attach as DFP, 1.5A | V(DFP_CC_MED) | 1.51 | 1.6 | 1.64 | V | configured as DFP advertising 1.5A | 6 |
| Voltage level for detecting a UFP attach as DFP, 3A | V(DFP_CC_HIGH) | 2.46 | 2.6 | 2.74 | V | configured as DFP advertising 3A | 6 |
| Voltage level for detecting an active cable attach as DFP, default current | V(AC_CC_USB) | 0.15 | 0.2 | 0.25 | V | configured as DFP advertising default current | 6 |
| Voltage level for detecting an active cable attach as DFP, 1.5A | V(AC_CC_MED) | 0.35 | 0.4 | 0.45 | V | configured as DFP advertising 1.5A | 6 |
| Voltage level for detecting an active cable attach as DFP, 3A | V(DFP_CC_HIGH) | 0.75 | 0.8 | 0.84 | V | active cable attach, configured as DFP advertising 3A | 7 |
| Default mode pull-up current source (DFP or DRP) | ICC(DEFAULT_P) | 64 | 80 | 96 | µA | | 7 |
| Medium (1.5A) mode pull-up current source (DFP or DRP) | ICC(MED_P) | 166 | 180 | 194 | µA | | 7 |
| High (3A) mode pull-up current source (DFP or DRP) | ICC(HIGH_P) | 34 | 330 | 356 | µA | as printed | 7 |
| Low-level input current | IIL | -10 | | 10 | µA | | 7 |
| Current leakage on ID pin | IID(LKG) | | | 10 | µA | VDD5 = 0V, ID = 5V | 7 |
| High-level input current (ENn_MUX) | IIH | -1 | | 1 | µA | ENn_MUX input | 7 |
| Low-level input current (ENn_MUX) | IIL | -1 | | 1 | µA | ENn_MUX input | 7 |
| Low-level signal output voltage (open drain) | VOL | | | 0.4 | V | OUT1, OUT2, INT_N/OUT3, ID, VCONN_FAULT_N, DIR; IOL = -1.6mA | 7 |
| High-level input voltage (I2C SDA/OUT1, SCL/OUT2) | VIH | 1.05 | | | V | I2C pins operating from 1.8/3.3V (±10%) | 7 |
| VBUS threshold range | V(BUS_THR) | 2.95 | 3.3 | 3.8 | V | VBUS_DET IO pin | 7 |
| External resistor between VBUS and VBUS_DET pin | RVBUS | 855 | 887 | 920 | KΩ | | 7 |
| VCONN current limit | I(VCONN) | 225 | 300 | 375 | mA | VCONN disconnected above this value | 7 |
| Current consumption in active mode, both CC controller and SS mux on | I(ACTIVE) | | 0.7 | 0.9 | mA | ENn_CC/Mux = L | 6 |
| Current consumption in shutdown mode | I(SHUTDOWN) | | | 5 | µA | ENn_CC/Mux = H | 6 |
| Data setup time | tSU:DAT | 100 | | | ns | I2C (SDA, SCL) | 8 |
| Data setup time (as printed) | tHD:DAT | 10 | | | ns | I2C (SDA, SCL) | 8 |
| Set-up time, SCL to start condition | tSU;STA | 0.6 | | | µs | I2C (SDA, SCL) | 8 |
| Data valid time | tVD;DAT | | | 0.9 | µs | I2C (SDA, SCL) | 8 |
| Bus free time between a STOP and START condition | tBUF | 1.3 | | | µs | I2C (SDA, SCL) | 8 |
| Rise time of both SDA and SCL signals | tr | | | 300 | ns | I2C (SDA, SCL) | 8 |
| Fall time of both SDA and SCL signals | tf | | | 300 | ns | I2C (SDA, SCL) | 8 |
| Total capacitive load for each bus line at ≤100KHz | CBUS_100KHZ | | | 400 | pF | operating at ≤100KHz | 8 |
| Total capacitive load for each bus line at 400KHz | CBUS_400KHZ | | | 100 | pF | operating at 400KHz | 8 |
| SCL clock frequency; I2C mode for local I2C control | fSCL | | | 400 | ns | as printed (unit ns) | 8 |
| Switching time DIR-to-Switch ON | tSW_ON | | | 0.5 | µs | See Figure 5-2 | 8 |
| Switching time DIR-to-Switch OFF | tSW_OFF | | | 0.5 | µs | See Figure 5-2 | 8 |
| ENn_CC high after both VDD5 and VCC33 stable | tENnCC_HI | 2 | | | ms | Refer to Figure 6-3 | 8 |
| VDD5 stable before VCC33 | tVDD5V_PG | 2 | | | ms | Refer to Figure 6-2 | 8 |
| Data valid acknowledge time | tVD;ACK | | | 0.9 | µs | I2C (SDA, SCL) | 8 |
| Junction-to-ambient thermal resistance | RθJA | | 60.9 | | °C/W | RNH (VQFN), 30 pins | 6 |
| Junction-to-case (top) thermal resistance | RθJC(top) | | 50.4 | | °C/W | RNH (VQFN), 30 pins | 6 |
| Junction-to-board thermal resistance | RθJB | | 22.8 | | °C/W | RNH (VQFN), 30 pins | 6 |
## CAD (Adom-generated)
- Symbol: `HD3SS3220IRNHR`
- Footprint: `Adom_Gen:Texas_Instruments_HD3_af6467`
- 3D model: generated to fit the land (STEP)
- 3D model files: `hd3ss3220irnhr-etched.step` / `hd3ss3220irnhr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `hd3ss3220irnhr.step` / `hd3ss3220irnhr.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/hd3ss3220.pdf) (48 pp, sha256 `44ad645ff24f1bf2`, retrieved 2026-11-17, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing; 3D model generated to fit that land.
[Datasheet PDF](docs/hd3ss3220irnhr-datasheet.pdf)