component
FT24C512A-TTR-T
Public Made by Adomby adom
FMD(Fremont Micro Devices) EEPROM, TSSOP-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
Ray
Publish 0.1.0
ee7e5c8
FT24C512A-TTR-T
FMD(Fremont Micro Devices) · EEPROM · TSSOP-8
FT24C512A-TTR-T from FMD(Fremont Micro Devices), in a TSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | A0 | input | Device address input that is hardwired to VIH or VIL and is recognized as VIL if left unconnected. |
| 2 | A1 | input | Device address input that is hardwired to VIH or VIL and is recognized as VIL if left unconnected. |
| 3 | A2 | input | Device address input that is hardwired to VIH or VIL and is recognized as VIL if left unconnected. |
| 4 | GND | power_in | Ground reference for the device. |
| 5 | SDA | bidirectional | Bi-directional serial data line with an open-drain output that can be wired-OR with other open-drain devices and is typically pulled high by an external resistor. |
| 6 | SCL | input | Serial clock input where the rising edge latches data into the EEPROM and the falling edge clocks data out. |
| 7 | WP | input | Write protect input that disables all programming when connected to VIH or VCC, while programming is allowed if left unconnected or at VIL; reads are unaffected. |
| 8 | VCC | power_in | Supply voltage of 1.7V to 5.5V, with a decoupling capacitor of no less than 10nF recommended. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | FMD(Fremont Micro Devices) |
| Package | TSSOP-8 |
| Category | Memory |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VCC1 | 1.7 | 5.5 | V | 11 | ||
| Supply read current | ICC1 | 0.4 | 1 | mA | VCC @ 5.5V SCL = 100 kHz | 11 | |
| Supply write current | ICC2 | 2 | 4 | mA | VCC @ 5.5V SCL = 100 kHz | 11 | |
| Standby supply current | ISB1 | 1 | µA | VCC @ 1.7V, VIN = VCC or VSS | 11 | ||
| Input leakage current | IIL | 3 | µA | VIN = VCC or VSS | 11 | ||
| Output leakage current | ILO | 3 | µA | VIN = VCC or VSS | 11 | ||
| Input low level | VIL | -0.6 | 0.3 | V | max = VCC×0.3 | 11 | |
| Input high level | VIH | 0.7 | 0.5 | V | min = VCC×0.7, max = VCC +0.5 | 11 | |
| Output low level | VOL1 | 0.4 | V | VCC @ 1.7V, IOL = 0.15 mA | 11 | ||
| Clock frequency, SCL (1.7V) | fSCL | 400 | kHz | 1.7V | 10 | ||
| Clock frequency, SCL (2.5-5.5V) | fSCL | 1000 | kHz | 2.5-5.5V | 10 | ||
| Clock pulse width low (1.7V) | tLOW | 1.3 | µs | 1.7V | 10 | ||
| Clock pulse width low (2.5-5.5V) | tLOW | 0.6 | µs | 2.5-5.5V | 10 | ||
| Clock pulse width high (1.7V) | tHIGH | 0.6 | µs | 1.7V | 10 | ||
| Clock pulse width high (2.5-5.5V) | tHIGH | 0.3 | µs | 2.5-5.5V | 10 | ||
| Noise suppression time (1.7V) | tI | 100 | ns | 1.7V | 10 | ||
| Noise suppression time (2.5-5.5V) | tI | 50 | ns | 2.5-5.5V | 10 | ||
| Clock low to data out valid (1.7V) | tAA | 0.9 | µs | 1.7V | 10 | ||
| Clock low to data out valid (2.5-5.5V) | tAA | 0.55 | µs | 2.5-5.5V | 10 | ||
| Bus free time (1.7V) | tBUF | 1.3 | µs | 1.7V | 10 | ||
| Bus free time (2.5-5.5V) | tBUF | 0.5 | µs | 2.5-5.5V | 10 | ||
| START hold time (1.7V) | tHD.STA | 0.6 | µs | 1.7V | 10 | ||
| START hold time (2.5-5.5V) | tHD.STA | 0.25 | µs | 2.5-5.5V | 10 | ||
| START set-up time (1.7V) | tSU.STA | 0.6 | µs | 1.7V | 10 | ||
| START set-up time (2.5-5.5V) | tSU.STA | 0.25 | µs | 2.5-5.5V | 10 | ||
| Data in hold time | tHD.DAT | 0 | µs | 1.7V and 2.5-5.5V | 10 | ||
| Data in set-up time | tSU.DAT | 100 | ns | 1.7V and 2.5-5.5V | 10 | ||
| Input rise time | tR | 0.3 | µs | 1.7V and 2.5-5.5V | 10 | ||
| Input fall time (1.7V) | tF | 300 | ns | 1.7V | 10 | ||
| Input fall time (2.5-5.5V) | tF | 100 | ns | 2.5-5.5V | 10 | ||
| STOP set-up time (1.7V) | tSU.STO | 0.6 | µs | 1.7V | 10 | ||
| STOP set-up time (2.5-5.5V) | tSU.STO | 0.25 | µs | 2.5-5.5V | 10 | ||
| Data out hold time | tDH | 50 | ns | 1.7V and 2.5-5.5V | 10 | ||
| VCC slew rate at power up | tPWR,R | 0.1 | 50 | V/ms | 1.7V and 2.5-5.5V | 10 | |
| Time required after VCC stable before commands | tPUP | 100 | µs | 1.7V and 2.5-5.5V | 10 | ||
| Minimum time at Vcc=0V between power cycles | tPOFF | 500 | ms | 1.7V and 2.5-5.5V | 10 | ||
| Write cycle time | tWR | 5 | ms | 1.7V and 2.5-5.5V | 10 | ||
| Endurance | 1e+06 | Write Cycles | 25°C, Page Mode, 3.3V | 10 | |||
| Input voltage on any pin relative to ground | -0.3 | V | max is VCC + 0.3V | 2 | |||
| Maximum voltage | 8 | V | 2 | ||||
| Storage temperature | -50 | 125 | °C | 2 | |||
| Industrial operating temperature | -40 | 85 | °C | 2 | |||
| ESD protection on all pins | 4000 | V | >4000V | 2 |
CAD (KiCad official)
- Symbol:
FT24C512A-TTR-T - Footprint:
Package_SO:TSSOP-8_3x3mm_P0.65mm - 3D model: TSSOP-8 (KiCad packages3D, STEP)
- 3D model files:
ft24c512a-ttr-t-etched.step/ft24c512a-ttr-t-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ft24c512a-ttr-t.step/ft24c512a-ttr-t.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: FMD(Fremont Micro Devices) datasheet (18 pp, sha256
066bca3721bc527b, retrieved 2026-10-22, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# FT24C512A-TTR-T
**FMD(Fremont Micro Devices)** · EEPROM · TSSOP-8
FT24C512A-TTR-T from FMD(Fremont Micro Devices), in a TSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | A0 | input | Device address input that is hardwired to VIH or VIL and is recognized as VIL if left unconnected. |
| 2 | A1 | input | Device address input that is hardwired to VIH or VIL and is recognized as VIL if left unconnected. |
| 3 | A2 | input | Device address input that is hardwired to VIH or VIL and is recognized as VIL if left unconnected. |
| 4 | GND | power_in | Ground reference for the device. |
| 5 | SDA | bidirectional | Bi-directional serial data line with an open-drain output that can be wired-OR with other open-drain devices and is typically pulled high by an external resistor. |
| 6 | SCL | input | Serial clock input where the rising edge latches data into the EEPROM and the falling edge clocks data out. |
| 7 | WP | input | Write protect input that disables all programming when connected to VIH or VCC, while programming is allowed if left unconnected or at VIL; reads are unaffected. |
| 8 | VCC | power_in | Supply voltage of 1.7V to 5.5V, with a decoupling capacitor of no less than 10nF recommended. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | FMD(Fremont Micro Devices) |
| Package | TSSOP-8 |
| Category | Memory |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VCC1 | 1.7 | | 5.5 | V | | 11 |
| Supply read current | ICC1 | | 0.4 | 1 | mA | VCC @ 5.5V SCL = 100 kHz | 11 |
| Supply write current | ICC2 | | 2 | 4 | mA | VCC @ 5.5V SCL = 100 kHz | 11 |
| Standby supply current | ISB1 | | | 1 | µA | VCC @ 1.7V, VIN = VCC or VSS | 11 |
| Input leakage current | IIL | | | 3 | µA | VIN = VCC or VSS | 11 |
| Output leakage current | ILO | | | 3 | µA | VIN = VCC or VSS | 11 |
| Input low level | VIL | -0.6 | | 0.3 | V | max = VCC×0.3 | 11 |
| Input high level | VIH | 0.7 | | 0.5 | V | min = VCC×0.7, max = VCC +0.5 | 11 |
| Output low level | VOL1 | | | 0.4 | V | VCC @ 1.7V, IOL = 0.15 mA | 11 |
| Clock frequency, SCL (1.7V) | fSCL | | | 400 | kHz | 1.7V | 10 |
| Clock frequency, SCL (2.5-5.5V) | fSCL | | | 1000 | kHz | 2.5-5.5V | 10 |
| Clock pulse width low (1.7V) | tLOW | 1.3 | | | µs | 1.7V | 10 |
| Clock pulse width low (2.5-5.5V) | tLOW | 0.6 | | | µs | 2.5-5.5V | 10 |
| Clock pulse width high (1.7V) | tHIGH | 0.6 | | | µs | 1.7V | 10 |
| Clock pulse width high (2.5-5.5V) | tHIGH | 0.3 | | | µs | 2.5-5.5V | 10 |
| Noise suppression time (1.7V) | tI | | | 100 | ns | 1.7V | 10 |
| Noise suppression time (2.5-5.5V) | tI | | | 50 | ns | 2.5-5.5V | 10 |
| Clock low to data out valid (1.7V) | tAA | | | 0.9 | µs | 1.7V | 10 |
| Clock low to data out valid (2.5-5.5V) | tAA | | | 0.55 | µs | 2.5-5.5V | 10 |
| Bus free time (1.7V) | tBUF | 1.3 | | | µs | 1.7V | 10 |
| Bus free time (2.5-5.5V) | tBUF | 0.5 | | | µs | 2.5-5.5V | 10 |
| START hold time (1.7V) | tHD.STA | 0.6 | | | µs | 1.7V | 10 |
| START hold time (2.5-5.5V) | tHD.STA | 0.25 | | | µs | 2.5-5.5V | 10 |
| START set-up time (1.7V) | tSU.STA | 0.6 | | | µs | 1.7V | 10 |
| START set-up time (2.5-5.5V) | tSU.STA | 0.25 | | | µs | 2.5-5.5V | 10 |
| Data in hold time | tHD.DAT | 0 | | | µs | 1.7V and 2.5-5.5V | 10 |
| Data in set-up time | tSU.DAT | 100 | | | ns | 1.7V and 2.5-5.5V | 10 |
| Input rise time | tR | | | 0.3 | µs | 1.7V and 2.5-5.5V | 10 |
| Input fall time (1.7V) | tF | | | 300 | ns | 1.7V | 10 |
| Input fall time (2.5-5.5V) | tF | | | 100 | ns | 2.5-5.5V | 10 |
| STOP set-up time (1.7V) | tSU.STO | 0.6 | | | µs | 1.7V | 10 |
| STOP set-up time (2.5-5.5V) | tSU.STO | 0.25 | | | µs | 2.5-5.5V | 10 |
| Data out hold time | tDH | 50 | | | ns | 1.7V and 2.5-5.5V | 10 |
| VCC slew rate at power up | tPWR,R | 0.1 | | 50 | V/ms | 1.7V and 2.5-5.5V | 10 |
| Time required after VCC stable before commands | tPUP | 100 | | | µs | 1.7V and 2.5-5.5V | 10 |
| Minimum time at Vcc=0V between power cycles | tPOFF | 500 | | | ms | 1.7V and 2.5-5.5V | 10 |
| Write cycle time | tWR | | | 5 | ms | 1.7V and 2.5-5.5V | 10 |
| Endurance | | 1e+06 | | | Write Cycles | 25°C, Page Mode, 3.3V | 10 |
| Input voltage on any pin relative to ground | | -0.3 | | | V | max is VCC + 0.3V | 2 |
| Maximum voltage | | | | 8 | V | | 2 |
| Storage temperature | | -50 | | 125 | °C | | 2 |
| Industrial operating temperature | | -40 | | 85 | °C | | 2 |
| ESD protection on all pins | | 4000 | | | V | >4000V | 2 |
## CAD (KiCad official)
- Symbol: `FT24C512A-TTR-T`
- Footprint: `Package_SO:TSSOP-8_3x3mm_P0.65mm`
- 3D model: TSSOP-8 (KiCad packages3D, STEP)
- 3D model files: `ft24c512a-ttr-t-etched.step` / `ft24c512a-ttr-t-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ft24c512a-ttr-t.step` / `ft24c512a-ttr-t.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [FMD(Fremont Micro Devices) datasheet](docs/ft24c512a-ttr-t-datasheet.pdf) (18 pp, sha256 `066bca3721bc527b`, retrieved 2026-10-22, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/ft24c512a-ttr-t-datasheet.pdf)