main
Ray Publish 0.1.0 a5de571

FT24C512A-TSR-B

FMD(Fremont Micro Devices) · EEPROM · SOP-8

FT24C512A-TSR-B from FMD(Fremont Micro Devices), in a SOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 A0 input Device address input, typically hardwired to VIH or VIL; if left unconnected it is internally recognized as VIL.
2 A1 input Device address input, typically hardwired to VIH or VIL; if left unconnected it is internally recognized as VIL.
3 A2 input Device address input, typically hardwired to VIH or VIL; if left unconnected it is internally recognized as VIL.
4 GND power_in Ground reference; input voltages are specified relative to ground, from -0.3V to VCC + 0.3V.
5 SDA bidirectional Bidirectional serial data line with open-drain output, typically pulled high by an external resistor and wire-ORable with other open-drain devices.
6 SCL input Serial clock input; the rising edge latches data into the device and the falling edge clocks data out.
7 WP input Write protect: connecting to VIH or VCC disables all programming of the array, while leaving it unconnected or at VIL allows programming; read operations are not affected.
8 VCC power_in Supply voltage of 1.8V to 5.5V for the FT24C512A; a decoupling capacitor no smaller than 10nF should be connected to the VCC pad.

Key specifications

Parameter Value
Manufacturer FMD(Fremont Micro Devices)
Package SOP-8
Category Memory
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage VCC1 1.8 5.5 V 24C××A supply VCC 11
Supply read current ICC1 0.4 1 mA VCC @ 5.5V, SCL = 100 kHz 11
Supply write current ICC2 2 3 mA VCC @ 5.5V, SCL = 100 kHz 11
Supply standby current ISB1 1 µA VCC @ 1.8V, VIN = VCC or VSS 11
Input leakage current IIL 3 µA VIN = VCC or VSS 11
Output leakage current ILO 3 µA VIN = VCC or VSS 11
Input low level VIL -0.6 V 11
Output low level VOL1 0.4 V VCC @ 1.8V, IOL = 0.15 mA 11
Clock frequency, SCL fSCL 400 kHz VCC 1.8V 10
Clock frequency, SCL fSCL 1000 kHz VCC 2.5-5.5V 10
Clock pulse width low tLOW 1.3 µs VCC 1.8V 10
Clock pulse width low tLOW 0.4 µs VCC 2.5-5.5V 10
Clock pulse width high tHIGH 0.6 µs VCC 1.8V 10
Clock pulse width high tHIGH 0.4 µs VCC 2.5-5.5V 10
Noise suppression time tI 100 ns VCC 1.8V; characterized, not fully screened (note 1) 10
Noise suppression time tI 50 ns VCC 2.5-5.5V; characterized, not fully screened (note 1) 10
Clock low to data out valid tAA 0.9 µs VCC 1.8V 10
Clock low to data out valid tAA 0.55 µs VCC 2.5-5.5V 10
Time the bus must be free before a new transmission can start tBUF 1.3 µs VCC 1.8V; characterized, not fully screened (note 1) 10
Time the bus must be free before a new transmission can start tBUF 0.5 µs VCC 2.5-5.5V; characterized, not fully screened (note 1) 10
START hold time tHD.STA 0.6 µs VCC 1.8V 10
START hold time tHD.STA 0.25 µs VCC 2.5-5.5V 10
START set-up time tSU.STA 0.6 µs VCC 1.8V 10
START set-up time tSU.STA 0.25 µs VCC 2.5-5.5V 10
Data in hold time tHD.DAT 0 µs VCC 1.8V 10
Data in set-up time tSU.DAT 100 ns VCC 1.8V 10
Input rise time tR 0.3 µs VCC 1.8V; characterized, not fully screened (note 1) 10
Input fall time tF 300 ns VCC 1.8V; characterized, not fully screened (note 1) 10
Input fall time tF 100 ns VCC 2.5-5.5V; characterized, not fully screened (note 1) 10
STOP set-up time tSU.STO 0.6 µs VCC 1.8V 10
STOP set-up time tSU.STO 0.25 µs VCC 2.5-5.5V 10
Data out hold time tDH 50 ns VCC 1.8V 10
Vcc slew rate at power up tPWR,R 0.1 50 V/ms VCC 1.8V 10
Time required after VCC is stable before the device can accept commands tPUP 100 µs VCC 1.8V 10
Minimum time at Vcc=0V between power cycles tPOFF 500 ms VCC 1.8V 10
Write cycle time tWR 5 ms VCC 1.8V 10
Storage temperature -50 125 °C 2
Industrial operating temperature -40 85 °C 2
Maximum voltage 8 V 2
ESD protection on all pins 4000 V Printed as >4000V 2
VCC slew rate during power-up (maximum) 0.05 V/µs Power-up sequence, VCC monotonic rise 8
Decoupling capacitor on VCC pad 10 nF Connected to VCC pad 8

CAD (KiCad official)

  • Symbol: FT24C512A-TSR-B
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SOP-8 (KiCad packages3D, STEP)
  • 3D model files: ft24c512a-tsr-b-etched.step / ft24c512a-tsr-b-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ft24c512a-tsr-b.step / ft24c512a-tsr-b.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: FMD(Fremont Micro Devices) datasheet (18 pp, sha256 26f3795d3d530d8a, retrieved 2026-10-28, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF