component
FT24C512A-TSR-B
Public Made by Adomby adom
FMD(Fremont Micro Devices) EEPROM, SOP-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
Generated by kicad-footprint-generator · KiCad file format 20260206
FT24C512A-TSR-B
FMD(Fremont Micro Devices) · EEPROM · SOP-8
FT24C512A-TSR-B from FMD(Fremont Micro Devices), in a SOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | A0 | input | Device address input, typically hardwired to VIH or VIL; if left unconnected it is internally recognized as VIL. |
| 2 | A1 | input | Device address input, typically hardwired to VIH or VIL; if left unconnected it is internally recognized as VIL. |
| 3 | A2 | input | Device address input, typically hardwired to VIH or VIL; if left unconnected it is internally recognized as VIL. |
| 4 | GND | power_in | Ground reference; input voltages are specified relative to ground, from -0.3V to VCC + 0.3V. |
| 5 | SDA | bidirectional | Bidirectional serial data line with open-drain output, typically pulled high by an external resistor and wire-ORable with other open-drain devices. |
| 6 | SCL | input | Serial clock input; the rising edge latches data into the device and the falling edge clocks data out. |
| 7 | WP | input | Write protect: connecting to VIH or VCC disables all programming of the array, while leaving it unconnected or at VIL allows programming; read operations are not affected. |
| 8 | VCC | power_in | Supply voltage of 1.8V to 5.5V for the FT24C512A; a decoupling capacitor no smaller than 10nF should be connected to the VCC pad. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | FMD(Fremont Micro Devices) |
| Package | SOP-8 |
| Category | Memory |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VCC1 | 1.8 | 5.5 | V | 24C××A supply VCC | 11 | |
| Supply read current | ICC1 | 0.4 | 1 | mA | VCC @ 5.5V, SCL = 100 kHz | 11 | |
| Supply write current | ICC2 | 2 | 3 | mA | VCC @ 5.5V, SCL = 100 kHz | 11 | |
| Supply standby current | ISB1 | 1 | µA | VCC @ 1.8V, VIN = VCC or VSS | 11 | ||
| Input leakage current | IIL | 3 | µA | VIN = VCC or VSS | 11 | ||
| Output leakage current | ILO | 3 | µA | VIN = VCC or VSS | 11 | ||
| Input low level | VIL | -0.6 | V | 11 | |||
| Output low level | VOL1 | 0.4 | V | VCC @ 1.8V, IOL = 0.15 mA | 11 | ||
| Clock frequency, SCL | fSCL | 400 | kHz | VCC 1.8V | 10 | ||
| Clock frequency, SCL | fSCL | 1000 | kHz | VCC 2.5-5.5V | 10 | ||
| Clock pulse width low | tLOW | 1.3 | µs | VCC 1.8V | 10 | ||
| Clock pulse width low | tLOW | 0.4 | µs | VCC 2.5-5.5V | 10 | ||
| Clock pulse width high | tHIGH | 0.6 | µs | VCC 1.8V | 10 | ||
| Clock pulse width high | tHIGH | 0.4 | µs | VCC 2.5-5.5V | 10 | ||
| Noise suppression time | tI | 100 | ns | VCC 1.8V; characterized, not fully screened (note 1) | 10 | ||
| Noise suppression time | tI | 50 | ns | VCC 2.5-5.5V; characterized, not fully screened (note 1) | 10 | ||
| Clock low to data out valid | tAA | 0.9 | µs | VCC 1.8V | 10 | ||
| Clock low to data out valid | tAA | 0.55 | µs | VCC 2.5-5.5V | 10 | ||
| Time the bus must be free before a new transmission can start | tBUF | 1.3 | µs | VCC 1.8V; characterized, not fully screened (note 1) | 10 | ||
| Time the bus must be free before a new transmission can start | tBUF | 0.5 | µs | VCC 2.5-5.5V; characterized, not fully screened (note 1) | 10 | ||
| START hold time | tHD.STA | 0.6 | µs | VCC 1.8V | 10 | ||
| START hold time | tHD.STA | 0.25 | µs | VCC 2.5-5.5V | 10 | ||
| START set-up time | tSU.STA | 0.6 | µs | VCC 1.8V | 10 | ||
| START set-up time | tSU.STA | 0.25 | µs | VCC 2.5-5.5V | 10 | ||
| Data in hold time | tHD.DAT | 0 | µs | VCC 1.8V | 10 | ||
| Data in set-up time | tSU.DAT | 100 | ns | VCC 1.8V | 10 | ||
| Input rise time | tR | 0.3 | µs | VCC 1.8V; characterized, not fully screened (note 1) | 10 | ||
| Input fall time | tF | 300 | ns | VCC 1.8V; characterized, not fully screened (note 1) | 10 | ||
| Input fall time | tF | 100 | ns | VCC 2.5-5.5V; characterized, not fully screened (note 1) | 10 | ||
| STOP set-up time | tSU.STO | 0.6 | µs | VCC 1.8V | 10 | ||
| STOP set-up time | tSU.STO | 0.25 | µs | VCC 2.5-5.5V | 10 | ||
| Data out hold time | tDH | 50 | ns | VCC 1.8V | 10 | ||
| Vcc slew rate at power up | tPWR,R | 0.1 | 50 | V/ms | VCC 1.8V | 10 | |
| Time required after VCC is stable before the device can accept commands | tPUP | 100 | µs | VCC 1.8V | 10 | ||
| Minimum time at Vcc=0V between power cycles | tPOFF | 500 | ms | VCC 1.8V | 10 | ||
| Write cycle time | tWR | 5 | ms | VCC 1.8V | 10 | ||
| Storage temperature | -50 | 125 | °C | 2 | |||
| Industrial operating temperature | -40 | 85 | °C | 2 | |||
| Maximum voltage | 8 | V | 2 | ||||
| ESD protection on all pins | 4000 | V | Printed as >4000V | 2 | |||
| VCC slew rate during power-up (maximum) | 0.05 | V/µs | Power-up sequence, VCC monotonic rise | 8 | |||
| Decoupling capacitor on VCC pad | 10 | nF | Connected to VCC pad | 8 |
CAD (KiCad official)
- Symbol:
FT24C512A-TSR-B - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOP-8 (KiCad packages3D, STEP)
- 3D model files:
ft24c512a-tsr-b-etched.step/ft24c512a-tsr-b-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ft24c512a-tsr-b.step/ft24c512a-tsr-b.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: FMD(Fremont Micro Devices) datasheet (18 pp, sha256
26f3795d3d530d8a, retrieved 2026-10-28, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).