component
FT24C128A-TSR-T
Public Made by Adomby adom
FMD(Fremont Micro Devices) EEPROM, SOP-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownFT24C128A-TSR-T
FMD(Fremont Micro Devices) · EEPROM · SOP-8
FT24C128A-TSR-T from FMD(Fremont Micro Devices), in a SOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | A0 | input | Device address input hardwired to VIH or VIL to match the device address; if left unconnected it is internally recognized as VIL. |
| 2 | A1 | input | Device address input hardwired to VIH or VIL to match the device address; if left unconnected it is internally recognized as VIL. |
| 3 | A2 | input | Device address input hardwired to VIH or VIL to match the device address; if left unconnected it is internally recognized as VIL. |
| 4 | GND | power_in | Ground reference pin; the datasheet labels it GND in the pin figure but gives no further description. |
| 5 | SDA | bidirectional | Bi-directional serial data line with open-drain output, typically pulled high by an external resistor and wire-OR-able with other open-drain devices; data changes only while SCL is at VIL. |
| 6 | SCL | input | Serial clock input whose rising edge latches data into the EEPROM and falling edge clocks data out; it is a Schmitt-trigger, noise-filtered input. |
| 7 | WP | input | Write protect input: programming is allowed when left unconnected or at VIL and all programming is disabled when connected to VIH or VCC, with read operations unaffected. |
| 8 | VCC | power_in | Supply voltage from 1.7 V to 5.5 V; a decoupling capacitor of no less than 10 nF should be connected to the VCC pad. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | FMD(Fremont Micro Devices) |
| Package | SOP-8 |
| Category | Memory |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VCC1 | 1.7 | 5.5 | V | 10 | ||
| Input low level | VIL | -0.6 | V | 10 | |||
| Input leakage current | IIL | 3 | µA | VIN = VCC or VSS | 10 | ||
| Output leakage current | ILO | 3 | µA | VIN = VCC or VSS | 10 | ||
| Supply read current | ICC1 | 0.3 | 1 | mA | VCC @ 5.5V SCL = 100 kHz | 10 | |
| Supply write current | ICC2 | 1 | 3 | mA | VCC @ 5.5V SCL = 100 kHz | 10 | |
| Standby supply current | ISB1 | 1 | µA | VCC @ 1.7V, VIN = VCC or VSS | 10 | ||
| Output low level | VOL1 | 0.4 | V | VCC @ 1.7V, IOL = 0.15 mA | 10 | ||
| Operating temperature range (industrial) | -40 | 85 | °C | 2 | |||
| Storage temperature | -50 | 125 | °C | 2 | |||
| Input voltage on any pin relative to ground | -0.3 | V | relative to ground | 2 | |||
| Maximum voltage | 8 | V | 2 | ||||
| ESD protection on all pins | 4000 | V | all pins; printed as >4000V | 2 | |||
| Clock frequency, SCL (1.7V) | fSCL | 400 | kHz | VCC 1.7V column | 9 | ||
| Clock frequency, SCL (2.5-5.5V) | fSCL | 1000 | kHz | VCC 2.5-5.5V column | 9 | ||
| Clock pulse width low (1.7V) | tLOW | 1.3 | µs | VCC 1.7V column | 9 | ||
| Clock pulse width low (2.5-5.5V) | tLOW | 0.6 | µs | VCC 2.5-5.5V column | 9 | ||
| Clock pulse width high (1.7V) | tHIGH | 0.6 | µs | VCC 1.7V column | 9 | ||
| Clock pulse width high (2.5-5.5V) | tHIGH | 0.3 | µs | VCC 2.5-5.5V column | 9 | ||
| Noise suppression time (1.7V) | tI | 100 | ns | VCC 1.7V column | 9 | ||
| Noise suppression time (2.5-5.5V) | tI | 50 | ns | VCC 2.5-5.5V column | 9 | ||
| Clock low to data out valid (1.7V) | tAA | 0.9 | µs | VCC 1.7V column | 9 | ||
| Clock low to data out valid (2.5-5.5V) | tAA | 0.55 | µs | VCC 2.5-5.5V column | 9 | ||
| Bus free time before new transmission (1.7V) | tBUF | 1.3 | µs | VCC 1.7V column | 9 | ||
| Bus free time before new transmission (2.5-5.5V) | tBUF | 0.5 | µs | VCC 2.5-5.5V column | 9 | ||
| START hold time (1.7V) | tHD.STA | 0.6 | µs | VCC 1.7V column | 9 | ||
| START hold time (2.5-5.5V) | tHD.STA | 0.25 | µs | VCC 2.5-5.5V column | 9 | ||
| START set-up time (1.7V) | tSU.STA | 0.6 | µs | VCC 1.7V column | 9 | ||
| START set-up time (2.5-5.5V) | tSU.STA | 0.25 | µs | VCC 2.5-5.5V column | 9 | ||
| Data in hold time (1.7V) | tHD.DAT | 0 | ns | VCC 1.7V column | 9 | ||
| Data in hold time (2.5-5.5V) | tHD.DAT | 0 | ns | VCC 2.5-5.5V column | 9 | ||
| Data in set-up time (1.7V) | tSU.DAT | 100 | ns | VCC 1.7V column | 9 | ||
| Data in set-up time (2.5-5.5V) | tSU.DAT | 100 | ns | VCC 2.5-5.5V column | 9 | ||
| Input rise time (1.7V) | tR | 300 | ns | VCC 1.7V column | 9 | ||
| Input rise time (2.5-5.5V) | tR | 100 | ns | VCC 2.5-5.5V column | 9 | ||
| Input fall time (1.7V) | tF | 300 | ns | VCC 1.7V column | 9 | ||
| Input fall time (2.5-5.5V) | tF | 100 | ns | VCC 2.5-5.5V column | 9 | ||
| STOP set-up time (1.7V) | tSU.STO | 0.6 | µs | VCC 1.7V column | 9 | ||
| STOP set-up time (2.5-5.5V) | tSU.STO | 0.25 | µs | VCC 2.5-5.5V column | 9 | ||
| Data out hold time (1.7V) | tDH | 50 | ns | VCC 1.7V column | 9 | ||
| Data out hold time (2.5-5.5V) | tDH | 50 | ns | VCC 2.5-5.5V column | 9 | ||
| VCC slew rate at power up (1.7V) | tPWR,R | 0.1 | 50 | V/ms | VCC 1.7V column | 9 | |
| VCC slew rate at power up (2.5-5.5V) | tPWR,R | 0.1 | 50 | V/ms | VCC 2.5-5.5V column | 9 | |
| Time required after VCC stable before device accepts commands (1.7V) | tPUP | 100 | µs | VCC 1.7V column | 9 | ||
| Time required after VCC stable before device accepts commands (2.5-5.5V) | tPUP | 100 | µs | VCC 2.5-5.5V column | 9 | ||
| Minimum time at VCC=0V between power cycles | tPOFF | 500 | ms | 9 | |||
| Write cycle time | tWR | 5 | ms | 9 | |||
| Endurance | 1e+06 | Write Cycles | 25oC, Page Mode, 3.3V | 9 |
CAD (KiCad official)
- Symbol:
FT24C128A-TSR-T - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOP-8 (KiCad packages3D, STEP)
- 3D model files:
ft24c128a-tsr-t-etched.step/ft24c128a-tsr-t-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ft24c128a-tsr-t.step/ft24c128a-tsr-t.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: FMD(Fremont Micro Devices) datasheet (18 pp, sha256
36c456866cdf8ed4, retrieved 2026-11-04, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).