component
FT232HPQ-TRAY
Public Made by Adomby adom
FTDI USB ICs, VQFN-56(8x8). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
Generated by kicad-footprint-generator · KiCad file format 20260206
FT232HPQ-TRAY
FTDI · USB ICs · VQFN-56(8x8)
FT232HPQ-TRAY from FTDI, in a VQFN-56(8x8). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EECS | bidirectional | EEPROM chip select pin, tri-stated during device reset, for the optional external EEPROM that holds the device configuration. |
| 2 | EECLK | output | Clock output to the external EEPROM, tri-stated during device reset and outputting the EEPROM clock when not in reset; pull to VCCIO with a separate 10K resistor if no EEPROM is used. |
| 3 | EEDATA | bidirectional | EEPROM data I/O, which connects to the EEPROM data-in directly and to data-out via a 2.2K resistor, with the data-out pulled to VCC via a 10K resistor for correct operation. |
| 4 | TEST | input | IC test pin that must be connected to GND for normal operation. |
| 5 | VCCIO | power_in | +3.3V I/O interface power supply input; failure to connect all VCCIO pins will result in failure of the device. |
| 6 | RESET# | input | Active-low reset input, with a minimum pulse width of 1.5 ms, and it should be tied to VCCIO (+3.3V) if not used. |
| 7 | GPIO0 | bidirectional | GPIO0 or I2C_SDA pin, with default function of GPIO0 input with weak pull-down. |
| 8 | GPIO1 | bidirectional | GPIO1 or I2C_SCL pin, with default function of GPIO1 input with weak pull-down. |
| 9 | GPIO2 | bidirectional | GPIO2 or I2C_INT# pin, with default function of GPIO2 input with weak pull-down. |
| 10 | GPIO3 | bidirectional | GPIO3 general purpose I/O pin, with default function of GPIO3 input with weak pull-down. |
| 11 | VCORE | power_in | +1.2V core supply voltage input; connect to pin 33 when using the internal regulator per the Table 2 note (VREGOUT to VCORE). |
| 12 | GND | power_in | Ground connection. |
| 13 | VCCIO | power_in | +3.3V I/O interface power supply input. |
| 14 | VCCIO | power_in | +3.3V I/O interface power supply input. |
| 15 | OSCI | input | Oscillator input pin. |
| 16 | OSCO | output | Oscillator output pin. |
| 17 | GND | power_in | Ground connection. |
| 18 | VREGIN | power_in | +3.3V input to the integrated 1.2V voltage regulator. |
| 19 | VREGOUT | power_out | +1.2V output of the integrated regulator, which must connect to VCORE with a 3.3uF filter capacitor and should not power other circuits. |
| 20 | FSOURCE | power_in | FSOURCE input pin for EFUSE, to be left floating for normal operation. |
| 21 | VPP | power_in | VPP input pin for EFUSE, to be left floating for normal operation. |
| 22 | VCORE | power_in | +1.2V core supply voltage input. |
| 23 | ADBUS0 | bidirectional | Configurable ADBUS pin, default function is transmit asynchronous data output (TXD) in UART mode. |
| 24 | ADBUS1 | bidirectional | Configurable ADBUS pin, default function is receive asynchronous data input (RXD) in UART mode. |
| 25 | ADBUS2 | bidirectional | Configurable ADBUS pin, default function is RTS# handshake control output in UART mode. |
| 26 | ADBUS3 | bidirectional | Configurable ADBUS pin, default function is CTS# handshake control input in UART mode. |
| 27 | ADBUS4 | bidirectional | Configurable ADBUS pin, default function is DTR# control output in UART mode. |
| 28 | VCCIO | power_in | +3.3V I/O interface power supply input. |
| 29 | ADBUS5 | bidirectional | Configurable ADBUS pin, default function is DSR# control input in UART mode. |
| 30 | ADBUS6 | bidirectional | Configurable ADBUS pin, default function is DCD# control input in UART mode. |
| 31 | ADBUS7 | bidirectional | Configurable ADBUS pin, default function is RI# control input in UART mode; when remote wake up is enabled in the EEPROM, taking it low can resume the host from suspend. |
| 32 | ACBUS0 | bidirectional | Configurable ACBUS I/O pin whose function is set in the EEPROM; default is TriSt-PU if no EEPROM is fitted. |
| 33 | ACBUS1 | bidirectional | Configurable ACBUS I/O pin whose function is set in the EEPROM; default is TriSt-PU if no EEPROM is fitted. |
| 34 | ACBUS2 | bidirectional | Configurable ACBUS I/O pin whose function is set in the EEPROM; default is TriSt-PU if no EEPROM is fitted. |
| 35 | ACBUS3 | bidirectional | Configurable ACBUS I/O pin whose function is set in the EEPROM; default is TriSt-PU if no EEPROM is fitted. |
| 36 | VCORE | power_in | +1.2V core supply voltage input. |
| 37 | ACBUS4 | bidirectional | Configurable ACBUS I/O pin whose function is set in the EEPROM; default is TriSt-PU if no EEPROM is fitted. |
| 38 | ACBUS5 | bidirectional | Configurable ACBUS I/O pin whose function is set in the EEPROM; default is TriSt-PU if no EEPROM is fitted. |
| 39 | ACBUS6 | bidirectional | Configurable ACBUS I/O pin whose function is set in the EEPROM; default is TriSt-PU if no EEPROM is fitted. |
| 40 | VCCIO | power_in | +3.3V I/O interface power supply input. |
| 41 | GND | power_in | Ground connection. |
| 42 | ACBUS7 | bidirectional | Configurable ACBUS I/O pin, default TriSt-PD if no EEPROM is fitted; also the PWRSAV# USB power save input, which can be tied to VCC_USB via a 39K resistor. |
| 43 | ACBUS8 | bidirectional | Configurable ACBUS I/O pin whose function is set in the EEPROM; default is TriSt-PU if no EEPROM is fitted. |
| 44 | ACBUS9 | bidirectional | Configurable ACBUS I/O pin whose function is set in the EEPROM; default is TriSt-PU if no EEPROM is fitted. |
| 45 | NC | unconnected | No function is given for this pin in the datasheet text; it is labelled NC on the 56-pin schematic symbol. |
| 46 | VCORE | power_in | +1.2V core supply voltage input. |
| 47 | VCC_USB | power_in | +3.3V input to the internal USB PHY; it cannot be connected directly to the USB supply and needs a +3.3V regulator with LC filtering. |
| 48 | DM | bidirectional | USB Data Signal Minus. |
| 49 | DP | bidirectional | USB Data Signal Plus. |
| 50 | REF | input | Current reference pin, to be connected to GND via a 12K resistor at 1% tolerance. |
| 51 | VCC_PD | power_in | +3.3V input to the internal PD PHY power supply. |
| 52 | PD1_CC2 | bidirectional | Analog I/O for the PD1 CC2 Type-C configuration channel pin. |
| 53 | PD1_SVBUS | passive | Analog input for scaled-down VBUS sensing on PD1; VBUS must be divided by 10 before this pin. |
| 54 | PD1_VCONN | power_in | Power input for the PD1 VCONN power source; connect to 3.3V. |
| 55 | PD1_CC1 | bidirectional | Analog I/O for the PD1 CC1 Type-C configuration channel pin. |
| 56 | VCORE | power_in | +1.2V core supply voltage input. |
| 57 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | FTDI |
| Package | VQFN-56(8x8) |
| Category | Communication Interface Chip/UART/485/232 |
| Pins | 57 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Storage Temperature | -65 | 150 | Degrees C | 46 | |||
| Ambient Operating Temperature (Power Applied) | -40 | 85 | Degrees C | Power applied | 46 | ||
| VCORE Supply Voltage | VCORE | -0.3 | 1.32 | V | 46 | ||
| VCCIO IO Voltage | VCCIO | -0.3 | 4 | V | 46 | ||
| DC Input Voltage, USBDP and USBDM | -0.5 | 3.63 | V | 46 | |||
| DC Input Voltage, High Impedance Bi-directional (ACBUS and ADBUS powered from VCCIO) | -0.3 | 5.8 | V | 46 | |||
| DC Output Current, Outputs | 16 | mA | 46 | ||||
| VCORE VCC Core Operating Supply Voltage | VCORE | 1.08 | 1.2 | 1.32 | V | 46 | |
| VCCIO Operating Supply Voltage | VCCIO | 2.97 | 3.3 | 3.63 | V | 46 | |
| VREGIN Voltage regulator Input | VREGIN | 3 | 3.3 | 3.6 | V | 46 | |
| VREGOUT Voltage regulator Output | VREGOUT | 1.08 | 1.2 | 1.32 | V | 46 | |
| Regulator Current | Ireg | 22.37 | 150 | mA | VREGIN +3.3V and data transfer with 12Mbps | 46 | |
| VREGIN Suspend Supply Current | Icc1s | 132.2 | µA | USB Suspend | 46 | ||
| VCC_USB operating supply current | I_vcc_usb | 22.36 | mA | Data transfer with 12Mbps | 46 | ||
| VCC_IO operating supply current | I_vccio | 1.72 | mA | Data transfer with 12Mbps | 46 | ||
| VCC_PD suspend supply current | I_vcc_pd | 23.5 | uA | PD suspend | 46 | ||
| Output Voltage High | Voh | 2.4 | V | Ioh = +/-2mA, I/O Drive strength = 4mA | 47 | ||
| Output Voltage Low | Vol | 0 | 0.4 | V | Iol = +/-2mA, I/O Drive strength = 4mA | 47 | |
| Input low Switching Threshold | Vil | 0.8 | V | LVTTL | 47 | ||
| Input High Switching Threshold | Vih | 2 | V | LVTTL | 47 | ||
| Schmitt trigger negative going threshold voltage | Vt- | 0.8 | 1.1 | V | 47 | ||
| Schmitt trigger positive going threshold voltage | Vt+ | 1.6 | 2 | V | 47 | ||
| Input pull-up resistance | Rpu | 40 | 75 | 190 | KΩ | Vin = 0 | 47 |
| Input pull-down resistance | Rpd | 40 | 75 | 190 | KΩ | Vin =VCCIO | 47 |
| Input Leakage Current | Iin | -1 | 1 | μA | Vin = 5V or 0V | 47 | |
| PHY Operating Supply Voltage | VCC_USB PHY | 3 | 3.3 | 3.6 | V | 3.3V I/O | 47 |
| PHY Operating Supply Current | Iccphy | 60 | mA | Hi-speed operation at 480 MHz | 47 | ||
| PHY Suspend Supply Current | Iccphy(susp) | 2 | mA | USB Suspend | 47 | ||
| PHY Output Voltage High | Voh | 2.8 | 3.6 | V | 47 | ||
| PHY Output Voltage Low | Vol | 0 | 0.3 | V | 47 | ||
| PHY Input low Switching Threshold | Vil | 0.8 | V | 47 | |||
| PHY Input High Switching Threshold | Vih | 2 | V | 47 | |||
| Human Body Model (HBM) | -2 | 2 | kV | JEDEC EIA/JESD22-A114-B, Class 2 | 48 | ||
| Machine Mode (MM) | -200 | 200 | V | JEDEC EIA/JESD22-A115-A, Class B | 48 | ||
| Charge Device Model (CDM) | -500 | 500 | V | JEDEC EIA/JESD22-C101-D, Class-III | 48 | ||
| Latch-up | -200 | 200 | mA | JESD78, Trigger Class-II | 48 | ||
| Thermal resistance junction to ambient (FT232HPQ) | ѲJA | 23.65 | °C/W | 48 | |||
| Thermal resistance junction to case (FT232HPQ) | ѲJC | 9.35 | °C/W | 48 |
CAD (KiCad official)
- Symbol:
FT232HPQ-TRAY - Footprint:
Package_DFN_QFN:QFN-56-1EP_8x8mm_P0.5mm_EP4.5x5.2mm - 3D model: VQFN-56(8x8) (KiCad packages3D, STEP)
- 3D model files:
ft232hpq-tray-etched.step/ft232hpq-tray-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ft232hpq-tray.step/ft232hpq-tray.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: FTDI datasheet (58 pp, sha256
7b97ec4256ec2c92, retrieved 2026-11-02, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).