component
FOD8316
Public Made by Adomby adom
onsemi Photoelectric Thyristor (Solid State Relays), SOIC-16-300mil. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
Ray
Publish 0.1.0
349d23d
FOD8316
onsemi · Photoelectric Thyristor (Solid State Relays) · SOIC-16-300mil
FOD8316 from onsemi, in a SOIC-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN+ | power_in | Non-inverting CMOS/TTL-compatible gate drive control input, with logic-high minimum 2.0 V, logic-low maximum 0.8 V, and absolute input range −0.5 V to VDD1. |
| 2 | VIN− | power_in | Inverting CMOS/TTL-compatible gate drive control input, with logic-high minimum 2.0 V, logic-low maximum 0.8 V, and absolute input range −0.5 V to VDD1. |
| 3 | VDD1 | power_in | Positive input supply voltage, 3 V to 5.5 V recommended (absolute maximum 6 V). |
| 4 | GND1 | power_in | Input-side ground reference for the input IC. |
| 5 | RESET | input | FAULT reset input that must be pulled low for longer than PWRESET to clear a latched fault, with the same logic thresholds as the VIN inputs. |
| 6 | FAULT | output | Open-drain fault output that is latched low on desaturation detection, with a maximum voltage of VDD1 and an absolute maximum current of 15 mA. |
| 7 | VLED1+ | unconnected | LED1 anode; the datasheet says do not connect, leave floating. |
| 8 | VLED1− | passive | LED1 cathode that must be connected to ground. |
| 9 | VSS | power_in | Negative output supply voltage for the gate driver output stage; VDD2 − VSS is recommended at 15 V to 30 V. |
| 10 | VSS | power_in | Negative output supply voltage for the gate driver output stage; VDD2 − VSS is recommended at 15 V to 30 V. |
| 11 | VO | output | Gate-drive output that drives the IGBT gate, with an absolute maximum peak output current of 3 A. |
| 12 | VS | power_in | Source of the pull-up PMOS transistor in the output stage, with recommended VS of VSS + 7.5 V to VDD2. |
| 13 | VDD2 | power_in | Positive output supply voltage, with VDD2 − VSS of 15 V to 30 V recommended (absolute maximum 35 V). |
| 14 | DESAT | input | Desaturation voltage input for IGBT short-circuit detection, referenced to VE, with a typical threshold of 6.5 V (6.0 V to 7.2 V). |
| 15 | VLED2+ | unconnected | LED2 anode; the datasheet says do not connect, leave floating. |
| 16 | VE | power_in | Output supply voltage and IGBT emitter reference, and the primary ground reference for UVLO and DESAT detection. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | SOIC-16-300mil |
| Category | Optocoupler/LED/Digital Tube/Photoelectric Device |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Storage Temperature | TSTG | -40 | 125 | °C | 5 | ||
| Operating Temperature | TOPR | -40 | 100 | °C | 5 | ||
| Junction Temperature | TJ | -40 | 125 | °C | 5 | ||
| Lead Wave Solder Temperature | TSOL | 260 | °C | for 10 seconds (No Solder Immersion) | 5 | ||
| Fault Output Current | IFAULT | 15 | mA | 5 | |||
| Peak Output Current | IO(PEAK) | 3 | A | Note 1 | 5 | ||
| Negative Output Supply Voltage | VE − VSS | 0 | 15 | V | Note 2 | 5 | |
| Positive Output Supply Voltage | VDD2 − VE | -0.5 | 35 | V | as printed: − (VE − VSS) in the value | 5 | |
| Gate Drive Output Voltage | VO(peak) | -0.5 | 35 | V | 5 | ||
| Output Supply Voltage | VDD2 − VSS | -0.5 | 35 | V | 5 | ||
| Positive Input Supply Voltage | VDD1 | -0.5 | 6 | V | 5 | ||
| Input Voltages | VIN+, VIN− and VRESET | -0.5 | V | max printed as VDD1 | 5 | ||
| Input Power Dissipation | PDI | 100 | mW | Notes 3, 5 | 5 | ||
| Output Power Dissipation | PDO | 600 | mW | Notes 4, 5; derate linearly above 64°C free air at 10.2 mW/°C | 5 | ||
| Ambient Operating Temperature | TA | -40 | 100 | °C | 5 | ||
| Input Supply Voltage | VDD1 | 3 | 5.5 | V | Note 6 | 5 | |
| Total Output Supply Voltage | VDD2 − VSS | 15 | 30 | V | 5 | ||
| Negative Output Supply Voltage | VE − VSS | 0 | 15 | V | 5 | ||
| Positive Output Supply Voltage | VDD2 − VE | 15 | 30 | V | Note 6; max printed as 30 − (VE − VSS) | 5 | |
| Logic Low Input Voltages | VIN+L, VIN−L, VRESETL | 0.8 | V | 6 | |||
| Logic High Input Voltages | VIN+H, VIN−H, VRESETH | 2 | V | 6 | |||
| Logic Low Input Currents | IIN+L, IIN−L, IRESETL | -0.5 | -0.001 | mA | VIN = 0.4 V | 6 | |
| FAULT Logic Low Output Current | IFAULTL | 5 | 12 | mA | VFAULT = 0.4 V | 6 | |
| FAULT Logic High Output Current | IFAULTH | -40 | 0.002 | A | VFAULT = VDD1 | 6 | |
| High Level Output Current | IOH | -1 | -2.5 | A | VO = VDD2 − 3 V | 6 | |
| High Level Output Current | IOH | -2.5 | A | VO = VDD2 − 6 V (Note 10) | 6 | ||
| Low Level Output Current | IOL | 1 | 3 | A | VO = VSS + 3 V | 6 | |
| Low Level Output Current | IOL | 2.5 | A | VO = VSS + 6 V (Note 11) | 6 | ||
| Low Level Output Current During Fault Condition | IOLF | 70 | 125 | 170 | mA | VO − VSS = 14 V | 6 |
| Low Level Output Voltage | VOL | 0.1 | 0.5 | V | IO = 100 mA | 6 | |
| High Level Supply Current | IDD1H | 14 | 17 | mA | VIN+ = VDD1 = 5.5 V, VIN− = 0 V | 6 | |
| Low Level Supply Current | IDD1L | 2 | 3 | mA | VIN+ = VIN− = 0 V, VDD1 = 5.5 V | 6 | |
| High Level Output Supply Current | IDD2H | 1.7 | 3 | mA | VO = Open (Note 14) | 6 | |
| Low Level Output Supply Current | IDD2L | 1.8 | 2.8 | mA | VO = Open | 6 | |
| High Level Source Current | ISH | 0.65 | 1.5 | mA | IO = 0 mA | 6 | |
| Low Level Source Current | ISL | 0.6 | 1.4 | mA | IO = 0 mA | 6 | |
| VE Low Level Supply Current | IEL | -0.8 | -0.5 | mA | 6 | ||
| VE High Level Supply Current | IEH | -0.5 | -0.25 | mA | 6 | ||
| Blanking Capacitor Charge Current | ICHG | -0.13 | -0.25 | -0.33 | mA | VDESAT = 2 V (Note 14, 15) | 6 |
| Blanking Capacitor Discharge Current | IDSCHG | 10 | 36 | mA | VDESAT = 7 V | 6 | |
| Under Voltage Lockout Threshold (rising) | VUVLO+ | 10.8 | 11.7 | 12.7 | V | VO > 5 V @ 25°C (Note 14) | 6 |
| Under Voltage Lockout Threshold (falling) | VUVLO− | 9.8 | 10.7 | 11.7 | V | VO < 5 V @ 25°C | 6 |
| Under Voltage Lockout Threshold Hysteresis | UVLOHYS | 0.4 | 1 | V | @ 25°C | 6 | |
| DESAT Threshold | VDESAT | 6 | 6.5 | 7.2 | V | VDD2 − VE > VULVO−, VO < 5 V (Note 14) | 6 |
| Propagation Delay Time to Logic Low Output | tPHL | 140 | 250 | ns | Rg = 10 , Cg = 10 nF, f = 10 kHz, Duty Cycle = 50% (Note 16) | 7 | |
| Propagation Delay Time to Logic High Output | tPLH | 160 | 250 | ns | Rg = 10 , Cg = 10 nF, f = 10 kHz, Duty Cycle = 50% (Note 16) | 7 | |
| Pulse Width Distortion | PWD | 20 | 100 | ns | / tPHL − tPLH / (Note 19) | 7 | |
| Skew Propagation Delay Difference between Any Two Parts or Channels | PDD | -150 | 150 | ns | (tPHL − tPLH) (Note 20) | 7 | |
| DESAT Sense to 90% VO Delay | tDESAT(90%) | 450 | 700 | ns | Rg = 10 , Cg = 10 nF, VDD2 − VSS = 30 V (Note 21) | 7 | |
| DESAT Sense to 10% VO Delay | tDESAT(10%) | 2.7 | 4 | s | (Note 21) | 7 | |
| DESAT Sense to Low Level FAULT Signal Delay | tDESAT(FAULT) | 1.4 | 5 | s | (Note 22) | 7 | |
| RESET to High Level FAULT Signal Delay | tRESET(FAULT) | 3 | 6 | 20 | s | (Note 24) | 7 |
| DESAT Input Mute | tDESAT(MUTE) | 10 | 22 | 35 | s | 7 | |
| RESET Signal Pulse Width | PWRESET | 1.2 | s | 7 | |||
| Common Mode Transient Immunity at Output High | /CMH/ | 35 | 50 | kV/s | TA = 25°C, VDD1 = 5 V, VDD2 = 25 V, VSS = Ground, VCM = 1500 Vpk (Note 28) | 7 | |
| Common Mode Transient Immunity at Output Low | /CML/ | 35 | 50 | kV/s | TA = 25°C, VDD1 = 5V, VDD2 = 25 V, VSS = Ground, VCM = 1500 Vpk (Note 29) | 7 | |
| Input−Output Isolation Voltage | VISO | 4243 | VRMS | TA = 25°C, Relative Humidity < 50 %, t = 1.0 minute, II−O ≤ 10 A, 50 Hz (Note 7, 8, 9) | 6 |
CAD (KiCad official)
- Symbol:
FOD8316 - Footprint:
Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm - 3D model: SOIC-16-300mil (KiCad packages3D, STEP)
- 3D model files:
fod8316-etched.step/fod8316-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);fod8316.step/fod8316.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: onsemi datasheet (28 pp, sha256
9a19dcf7f95068f2, retrieved 2026-11-10, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# FOD8316
**onsemi** · Photoelectric Thyristor (Solid State Relays) · SOIC-16-300mil
FOD8316 from onsemi, in a SOIC-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN+ | power_in | Non-inverting CMOS/TTL-compatible gate drive control input, with logic-high minimum 2.0 V, logic-low maximum 0.8 V, and absolute input range −0.5 V to VDD1. |
| 2 | VIN− | power_in | Inverting CMOS/TTL-compatible gate drive control input, with logic-high minimum 2.0 V, logic-low maximum 0.8 V, and absolute input range −0.5 V to VDD1. |
| 3 | VDD1 | power_in | Positive input supply voltage, 3 V to 5.5 V recommended (absolute maximum 6 V). |
| 4 | GND1 | power_in | Input-side ground reference for the input IC. |
| 5 | RESET | input | FAULT reset input that must be pulled low for longer than PWRESET to clear a latched fault, with the same logic thresholds as the VIN inputs. |
| 6 | FAULT | output | Open-drain fault output that is latched low on desaturation detection, with a maximum voltage of VDD1 and an absolute maximum current of 15 mA. |
| 7 | VLED1+ | unconnected | LED1 anode; the datasheet says do not connect, leave floating. |
| 8 | VLED1− | passive | LED1 cathode that must be connected to ground. |
| 9 | VSS | power_in | Negative output supply voltage for the gate driver output stage; VDD2 − VSS is recommended at 15 V to 30 V. |
| 10 | VSS | power_in | Negative output supply voltage for the gate driver output stage; VDD2 − VSS is recommended at 15 V to 30 V. |
| 11 | VO | output | Gate-drive output that drives the IGBT gate, with an absolute maximum peak output current of 3 A. |
| 12 | VS | power_in | Source of the pull-up PMOS transistor in the output stage, with recommended VS of VSS + 7.5 V to VDD2. |
| 13 | VDD2 | power_in | Positive output supply voltage, with VDD2 − VSS of 15 V to 30 V recommended (absolute maximum 35 V). |
| 14 | DESAT | input | Desaturation voltage input for IGBT short-circuit detection, referenced to VE, with a typical threshold of 6.5 V (6.0 V to 7.2 V). |
| 15 | VLED2+ | unconnected | LED2 anode; the datasheet says do not connect, leave floating. |
| 16 | VE | power_in | Output supply voltage and IGBT emitter reference, and the primary ground reference for UVLO and DESAT detection. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | SOIC-16-300mil |
| Category | Optocoupler/LED/Digital Tube/Photoelectric Device |
| Pins | 16 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Storage Temperature | TSTG | -40 | | 125 | °C | | 5 |
| Operating Temperature | TOPR | -40 | | 100 | °C | | 5 |
| Junction Temperature | TJ | -40 | | 125 | °C | | 5 |
| Lead Wave Solder Temperature | TSOL | | | 260 | °C | for 10 seconds (No Solder Immersion) | 5 |
| Fault Output Current | IFAULT | | | 15 | mA | | 5 |
| Peak Output Current | IO(PEAK) | | | 3 | A | Note 1 | 5 |
| Negative Output Supply Voltage | VE − VSS | 0 | | 15 | V | Note 2 | 5 |
| Positive Output Supply Voltage | VDD2 − VE | -0.5 | | 35 | V | as printed: − (VE − VSS) in the value | 5 |
| Gate Drive Output Voltage | VO(peak) | -0.5 | | 35 | V | | 5 |
| Output Supply Voltage | VDD2 − VSS | -0.5 | | 35 | V | | 5 |
| Positive Input Supply Voltage | VDD1 | -0.5 | | 6 | V | | 5 |
| Input Voltages | VIN+, VIN− and VRESET | -0.5 | | | V | max printed as VDD1 | 5 |
| Input Power Dissipation | PDI | | | 100 | mW | Notes 3, 5 | 5 |
| Output Power Dissipation | PDO | | | 600 | mW | Notes 4, 5; derate linearly above 64°C free air at 10.2 mW/°C | 5 |
| Ambient Operating Temperature | TA | -40 | | 100 | °C | | 5 |
| Input Supply Voltage | VDD1 | 3 | | 5.5 | V | Note 6 | 5 |
| Total Output Supply Voltage | VDD2 − VSS | 15 | | 30 | V | | 5 |
| Negative Output Supply Voltage | VE − VSS | 0 | | 15 | V | | 5 |
| Positive Output Supply Voltage | VDD2 − VE | 15 | | 30 | V | Note 6; max printed as 30 − (VE − VSS) | 5 |
| Logic Low Input Voltages | VIN+L, VIN−L, VRESETL | | | 0.8 | V | | 6 |
| Logic High Input Voltages | VIN+H, VIN−H, VRESETH | 2 | | | V | | 6 |
| Logic Low Input Currents | IIN+L, IIN−L, IRESETL | -0.5 | -0.001 | | mA | VIN = 0.4 V | 6 |
| FAULT Logic Low Output Current | IFAULTL | 5 | 12 | | mA | VFAULT = 0.4 V | 6 |
| FAULT Logic High Output Current | IFAULTH | -40 | 0.002 | | A | VFAULT = VDD1 | 6 |
| High Level Output Current | IOH | -1 | -2.5 | | A | VO = VDD2 − 3 V | 6 |
| High Level Output Current | IOH | -2.5 | | | A | VO = VDD2 − 6 V (Note 10) | 6 |
| Low Level Output Current | IOL | 1 | 3 | | A | VO = VSS + 3 V | 6 |
| Low Level Output Current | IOL | 2.5 | | | A | VO = VSS + 6 V (Note 11) | 6 |
| Low Level Output Current During Fault Condition | IOLF | 70 | 125 | 170 | mA | VO − VSS = 14 V | 6 |
| Low Level Output Voltage | VOL | | 0.1 | 0.5 | V | IO = 100 mA | 6 |
| High Level Supply Current | IDD1H | | 14 | 17 | mA | VIN+ = VDD1 = 5.5 V, VIN− = 0 V | 6 |
| Low Level Supply Current | IDD1L | | 2 | 3 | mA | VIN+ = VIN− = 0 V, VDD1 = 5.5 V | 6 |
| High Level Output Supply Current | IDD2H | | 1.7 | 3 | mA | VO = Open (Note 14) | 6 |
| Low Level Output Supply Current | IDD2L | | 1.8 | 2.8 | mA | VO = Open | 6 |
| High Level Source Current | ISH | | 0.65 | 1.5 | mA | IO = 0 mA | 6 |
| Low Level Source Current | ISL | | 0.6 | 1.4 | mA | IO = 0 mA | 6 |
| VE Low Level Supply Current | IEL | -0.8 | -0.5 | | mA | | 6 |
| VE High Level Supply Current | IEH | -0.5 | -0.25 | | mA | | 6 |
| Blanking Capacitor Charge Current | ICHG | -0.13 | -0.25 | -0.33 | mA | VDESAT = 2 V (Note 14, 15) | 6 |
| Blanking Capacitor Discharge Current | IDSCHG | 10 | 36 | | mA | VDESAT = 7 V | 6 |
| Under Voltage Lockout Threshold (rising) | VUVLO+ | 10.8 | 11.7 | 12.7 | V | VO > 5 V @ 25°C (Note 14) | 6 |
| Under Voltage Lockout Threshold (falling) | VUVLO− | 9.8 | 10.7 | 11.7 | V | VO < 5 V @ 25°C | 6 |
| Under Voltage Lockout Threshold Hysteresis | UVLOHYS | 0.4 | 1 | | V | @ 25°C | 6 |
| DESAT Threshold | VDESAT | 6 | 6.5 | 7.2 | V | VDD2 − VE > VULVO−, VO < 5 V (Note 14) | 6 |
| Propagation Delay Time to Logic Low Output | tPHL | | 140 | 250 | ns | Rg = 10 , Cg = 10 nF, f = 10 kHz, Duty Cycle = 50% (Note 16) | 7 |
| Propagation Delay Time to Logic High Output | tPLH | | 160 | 250 | ns | Rg = 10 , Cg = 10 nF, f = 10 kHz, Duty Cycle = 50% (Note 16) | 7 |
| Pulse Width Distortion | PWD | | 20 | 100 | ns | / tPHL − tPLH / (Note 19) | 7 |
| Skew Propagation Delay Difference between Any Two Parts or Channels | PDD | -150 | | 150 | ns | (tPHL − tPLH) (Note 20) | 7 |
| DESAT Sense to 90% VO Delay | tDESAT(90%) | | 450 | 700 | ns | Rg = 10 , Cg = 10 nF, VDD2 − VSS = 30 V (Note 21) | 7 |
| DESAT Sense to 10% VO Delay | tDESAT(10%) | | 2.7 | 4 | s | (Note 21) | 7 |
| DESAT Sense to Low Level FAULT Signal Delay | tDESAT(FAULT) | | 1.4 | 5 | s | (Note 22) | 7 |
| RESET to High Level FAULT Signal Delay | tRESET(FAULT) | 3 | 6 | 20 | s | (Note 24) | 7 |
| DESAT Input Mute | tDESAT(MUTE) | 10 | 22 | 35 | s | | 7 |
| RESET Signal Pulse Width | PWRESET | 1.2 | | | s | | 7 |
| Common Mode Transient Immunity at Output High | /CMH/ | 35 | 50 | | kV/s | TA = 25°C, VDD1 = 5 V, VDD2 = 25 V, VSS = Ground, VCM = 1500 Vpk (Note 28) | 7 |
| Common Mode Transient Immunity at Output Low | /CML/ | 35 | 50 | | kV/s | TA = 25°C, VDD1 = 5V, VDD2 = 25 V, VSS = Ground, VCM = 1500 Vpk (Note 29) | 7 |
| Input−Output Isolation Voltage | VISO | 4243 | | | VRMS | TA = 25°C, Relative Humidity < 50 %, t = 1.0 minute, II−O ≤ 10 A, 50 Hz (Note 7, 8, 9) | 6 |
## CAD (KiCad official)
- Symbol: `FOD8316`
- Footprint: `Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm`
- 3D model: SOIC-16-300mil (KiCad packages3D, STEP)
- 3D model files: `fod8316-etched.step` / `fod8316-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `fod8316.step` / `fod8316.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [onsemi datasheet](https://www.onsemi.com/pdf/datasheet/fod8316-d.pdf) (28 pp, sha256 `9a19dcf7f95068f2`, retrieved 2026-11-10, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/fod8316-datasheet.pdf)