component
F28P550SJ9PDTR
Public Made by Adomby adom
Texas Instruments , TQFP-128(14x14). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownF28P550SJ9PDTR
Texas Instruments · IC · TQFP-128(14x14)
F28P550SJ9PDTR from Texas Instruments, in a TQFP-128(14x14). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GPIO29 | bidirectional | General-purpose I/O 29 with muxed digital peripheral functions. |
| 2 | GPIO28 | bidirectional | General-purpose I/O 28 shared with analog inputs A16, B16, C16. |
| 3 | XRSn | bidirectional | Open-drain device reset input and watchdog reset output with internal pullup; use a 2.2 kΩ to 10 kΩ resistor to VDDIO and at most 100 nF to VSS. |
| 4 | GPIO46 | bidirectional | General-purpose I/O 46 with muxed digital peripheral functions. |
| 5 | VDDIO | power_in | 3.3-V digital I/O power pin; place a minimum 0.1-µF decoupling capacitor on each pin. |
| 6 | VDD | power_in | 1.2-V digital logic power pin; about 10 µF minimum total decoupling, connect all VDD pins together when internal VREG is used. |
| 7 | VSS | power_in | Digital ground; must be connected to board ground. |
| 8 | GPIO47 | bidirectional | General-purpose I/O 47 with muxed digital peripheral functions. |
| 9 | GPIO66 | bidirectional | General-purpose I/O 66 with muxed digital peripheral functions. |
| 10 | GPIO67 | bidirectional | General-purpose I/O 67 with muxed digital peripheral functions. |
| 11 | GPIO48 | bidirectional | General-purpose I/O 48 with muxed digital peripheral functions. |
| 12 | GPIO49 | bidirectional | General-purpose I/O 49 with muxed digital peripheral functions. |
| 13 | GPIO50 | bidirectional | General-purpose I/O 50 with muxed digital peripheral functions. |
| 14 | GPIO51 | bidirectional | General-purpose I/O 51 with muxed digital peripheral functions. |
| 15 | GPIO52 | bidirectional | General-purpose I/O 52 with muxed digital peripheral functions. |
| 16 | GPIO53 | bidirectional | General-purpose I/O 53 with muxed digital peripheral functions. |
| 17 | GPIO54 | bidirectional | General-purpose I/O 54 with muxed digital peripheral functions. |
| 18 | A6,D14,E14,GPIO228 | bidirectional | ADC-A6, ADC-D14, ADC-E14 analog inputs shared with GPIO228. |
| 19 | B2,C6,E12,GPIO226 | bidirectional | ADC-B2, ADC-C6, ADC-E12 analog inputs shared with GPIO226. |
| 20 | A3,B3,C5,GPIO242,PGA2_INP | bidirectional | ADC-A3, ADC-B3, ADC-C5 analog inputs and PGA-2 positive input shared with GPIO242. |
| 21 | A2,B6,C9,GPIO224,PGA1_INP | bidirectional | ADC-A2, ADC-B6, ADC-C9 analog inputs and PGA-1 positive input shared with GPIO224. |
| 22 | A15,B9,C7,PGA1_INM | input | ADC-A15, ADC-B9, ADC-C7 analog inputs and PGA-1 inverting input. |
| 23 | C25,D5,E5 | input | ADC-C25, ADC-D5, ADC-E5 analog inputs. |
| 24 | A26,D6,E6 | input | ADC-A26, ADC-D6, ADC-E6 analog inputs. |
| 25 | B26,D7,E7 | input | ADC-B26, ADC-D7, ADC-E7 analog inputs. |
| 26 | A14/B14/C4/PGA1_OUT | input | ADC-A14, ADC-B14, ADC-C4 analog inputs and PGA-1 output. |
| 27 | A11/B10/C0/PGA2_OUT | input | ADC-A11, ADC-B10, ADC-C0 analog inputs and PGA-2 output. |
| 28 | A5,B12,C2,PGA2_INM | input | ADC-A5, ADC-B12, ADC-C2 analog inputs and PGA-2 inverting input. |
| 29 | A1,B7,CMP1_DACL,D11 | input | ADC-A1, ADC-B7, ADC-D11 analog inputs and CMPSS-1 low DAC output. |
| 30 | A0/B15/C15/DACA_OUT | bidirectional | ADC-A0, ADC-B15, ADC-C15 analog inputs and buffered DAC-A output. |
| 31 | VREFHI | input | ADC high reference; tie to VDDA if the ADC is unused. |
| 32 | VREFHI | input | ADC high reference (second pin); tie to VDDA if the ADC is unused. |
| 33 | VREFLO | input | ADC low reference (also ADC-A13, B13, C13, D13, E13); tie to VSSA if unused. |
| 34 | VREFLO | input | ADC low reference (second pin, also ADC-A13, B13, C13, D13, E13); tie to VSSA if unused. |
| 35 | A12,C1,E11,PGA3_INP | input | ADC-A12, ADC-C1, ADC-E11 analog inputs and PGA-3 positive input. |
| 36 | B11,D16,E16,PGA3_INM | input | ADC-B11, ADC-D16, ADC-E16 analog inputs and PGA-3 inverting input. |
| 37 | A7/B30/C3/D12/E30 | input | ADC-A7, ADC-B30, ADC-C3, ADC-D12, ADC-E30 analog inputs. |
| 38 | B5,D15,E15,PGA3_OUT | input | ADC-B5, ADC-D15, ADC-E15 analog inputs and PGA-3 output. |
| 39 | A8/B0/C11 | input | ADC-A8, ADC-B0, ADC-C11 analog inputs. |
| 40 | VSSA | power_in | Analog ground; tie to VSS if no separate analog ground is used. |
| 41 | VDDA | power_in | 3.3-V analog power pin; place a minimum 2.2-µF decoupling capacitor. |
| 42 | A4,B8,C14 | input | ADC-A4, ADC-B8, ADC-C14 analog inputs. |
| 43 | C26,D8,E8,GPIO211 | input | ADC-C26, ADC-D8, ADC-E8 analog inputs shared with GPIO211. |
| 44 | A27,D9,E9,GPIO212 | input | ADC-A27, ADC-D9, ADC-E9 analog inputs shared with GPIO212. |
| 45 | B27,D10,E10,GPIO213 | input | ADC-B27, ADC-D10, ADC-E10 analog inputs shared with GPIO213. |
| 46 | C27,D18,E18,GPIO214 | input | ADC-C27, ADC-D18, ADC-E18 analog inputs shared with GPIO214. |
| 47 | A28,D19,E19,GPIO215 | input | ADC-A28, ADC-D19, ADC-E19 analog inputs shared with GPIO215. |
| 48 | A9,GPIO227 | bidirectional | ADC-A9 analog input shared with GPIO227. |
| 49 | B4,C8,GPIO236 | bidirectional | ADC-B4, ADC-C8 analog inputs shared with GPIO236. |
| 50 | A10,B1,C10,GPIO230 | bidirectional | ADC-A10, ADC-B1, ADC-C10 analog inputs shared with GPIO230. |
| 51 | GPIO55 | bidirectional | General-purpose I/O 55 with muxed digital peripheral functions. |
| 52 | GPIO60 | bidirectional | General-purpose I/O 60 with muxed digital peripheral functions. |
| 53 | VSS | power_in | Digital ground; must be connected to board ground. |
| 54 | VDD | power_in | 1.2-V digital logic power pin; about 10 µF minimum total decoupling, connect all VDD pins together when internal VREG is used. |
| 55 | VDDIO | power_in | 3.3-V digital I/O power pin; place a minimum 0.1-µF decoupling capacitor on each pin. |
| 56 | GPIO64 | bidirectional | General-purpose I/O 64 with muxed digital peripheral functions. |
| 57 | GPIO65 | bidirectional | General-purpose I/O 65 with muxed digital peripheral functions. |
| 58 | GPIO62 | bidirectional | General-purpose I/O 62 with muxed digital peripheral functions. |
| 59 | GPIO63 | bidirectional | General-purpose I/O 63 with muxed digital peripheral functions. |
| 60 | A17,B17,C17,GPIO20 | bidirectional | ADC-A17, ADC-B17, ADC-C17 analog inputs shared with GPIO20. |
| 61 | A18,B18,C18,GPIO21 | bidirectional | ADC-A18, ADC-B18, ADC-C18 analog inputs shared with GPIO21. |
| 62 | A19,B19,C19,GPIO13 | bidirectional | ADC-A19, ADC-B19, ADC-C19 analog inputs shared with GPIO13. |
| 63 | A20,B20,C20,GPIO12 | bidirectional | ADC-A20, ADC-B20, ADC-C20 analog inputs shared with GPIO12. |
| 64 | A24,D0,E0,GPIO11 | bidirectional | ADC-A24, ADC-D0, ADC-E0 analog inputs shared with GPIO11. |
| 65 | B24,D1,E1,GPIO33 | bidirectional | ADC-B24, ADC-D1, ADC-E1 analog inputs shared with GPIO33. |
| 66 | C24,D2,E2,GPIO16 | bidirectional | ADC-C24, ADC-D2, ADC-E2 analog inputs shared with GPIO16. |
| 67 | A25,D3,E3,GPIO17 | bidirectional | ADC-A25, ADC-D3, ADC-E3 analog inputs shared with GPIO17. |
| 68 | B25,D4,E4,GPIO24 | bidirectional | ADC-B25, ADC-D4, ADC-E4 analog inputs shared with GPIO24. |
| 69 | GPIO25 | bidirectional | General-purpose I/O 25 with muxed digital peripheral functions. |
| 70 | GPIO26 | bidirectional | General-purpose I/O 26 with muxed digital peripheral functions. |
| 71 | GPIO27 | bidirectional | General-purpose I/O 27 with muxed digital peripheral functions. |
| 72 | GPIO68 | bidirectional | General-purpose I/O 68 with muxed digital peripheral functions. |
| 73 | GPIO69 | bidirectional | General-purpose I/O 69 with muxed digital peripheral functions. |
| 74 | GPIO70 | bidirectional | General-purpose I/O 70 with muxed digital peripheral functions. |
| 75 | TCK | input | JTAG test clock with internal pullup. |
| 76 | GPIO37/TDO | bidirectional | JTAG test data output (default mux), tri-stated without JTAG activity so enable internal pullup or add an external pullup. |
| 77 | TMS | bidirectional | JTAG test-mode select with internal pullup; add an external pullup (recommended 2.2 kΩ) to VDDIO. |
| 78 | GPIO35/TDI | bidirectional | JTAG test data input (default mux); enable internal pullup or add an external pullup to avoid a floating input. |
| 79 | GPIO32 | bidirectional | General-purpose I/O 32, a 5-V fail-safe tolerant pin. |
| 80 | GPIO56 | bidirectional | General-purpose I/O 56 with muxed digital peripheral functions. |
| 81 | GPIO57 | bidirectional | General-purpose I/O 57 with muxed digital peripheral functions. |
| 82 | GPIO58 | bidirectional | General-purpose I/O 58 with muxed digital peripheral functions. |
| 83 | GPIO71 | bidirectional | General-purpose I/O 71 with muxed digital peripheral functions. |
| 84 | GPIO72 | bidirectional | General-purpose I/O 72 with muxed digital peripheral functions. |
| 85 | GPIO73 | bidirectional | General-purpose I/O 73 with muxed digital peripheral functions. |
| 86 | GPIO74 | bidirectional | General-purpose I/O 74 with muxed digital peripheral functions. |
| 87 | GPIO18/X2 | bidirectional | General-purpose I/O 18 or crystal oscillator output X2. |
| 88 | GPIO19/X1 | bidirectional | General-purpose I/O 19 or crystal oscillator input X1 / single-ended 3.3-V clock input. |
| 89 | VDDIO | power_in | 3.3-V digital I/O power pin; place a minimum 0.1-µF decoupling capacitor on each pin. |
| 90 | VDD | power_in | 1.2-V digital logic power pin; about 10 µF minimum total decoupling, connect all VDD pins together when internal VREG is used. |
| 91 | GPIO43 | bidirectional | General-purpose I/O 43 with muxed digital peripheral functions. |
| 92 | VSS | power_in | Digital ground; must be connected to board ground. |
| 93 | VREGENZ | input | Internal voltage regulator enable with internal pulldown; tie low to VSS to enable internal VREG, high to VDDIO for external supply. |
| 94 | GPIO42 | bidirectional | General-purpose I/O 42, located near the power management module so avoid negative noise below VSS - 0.3 V. |
| 95 | GPIO8 | bidirectional | General-purpose I/O 8, located near the power management module so avoid negative noise below VSS - 0.3 V. |
| 96 | GPIO4 | bidirectional | General-purpose I/O 4 with muxed digital peripheral functions. |
| 97 | GPIO3 | bidirectional | General-purpose I/O 3, a 5-V fail-safe tolerant pin. |
| 98 | GPIO2 | bidirectional | General-purpose I/O 2, a 5-V fail-safe tolerant pin. |
| 99 | GPIO1 | bidirectional | General-purpose I/O 1 with muxed digital peripheral functions. |
| 100 | GPIO0 | bidirectional | General-purpose I/O 0 with muxed digital peripheral functions. |
| 101 | GPIO40 | bidirectional | General-purpose I/O 40 with muxed digital peripheral functions. |
| 102 | GPIO23 | bidirectional | General-purpose I/O 23, also USB-0 PHY differential data (USB0DM). |
| 103 | GPIO41 | bidirectional | General-purpose I/O 41, also USB-0 PHY differential data (USB0DP). |
| 104 | GPIO22 | bidirectional | General-purpose I/O 22 with muxed digital peripheral functions. |
| 105 | GPIO7 | bidirectional | General-purpose I/O 7 with muxed digital peripheral functions. |
| 106 | GPIO44 | bidirectional | General-purpose I/O 44 with muxed digital peripheral functions. |
| 107 | VSS | power_in | Digital ground; must be connected to board ground. |
| 108 | VDD | power_in | 1.2-V digital logic power pin; about 10 µF minimum total decoupling, connect all VDD pins together when internal VREG is used. |
| 109 | VDDIO | power_in | 3.3-V digital I/O power pin; place a minimum 0.1-µF decoupling capacitor on each pin. |
| 110 | GPIO45 | bidirectional | General-purpose I/O 45 with muxed digital peripheral functions. |
| 111 | GPIO75 | bidirectional | General-purpose I/O 75 with muxed digital peripheral functions. |
| 112 | GPIO76 | bidirectional | General-purpose I/O 76 with muxed digital peripheral functions. |
| 113 | GPIO77 | bidirectional | General-purpose I/O 77 with muxed digital peripheral functions. |
| 114 | GPIO78 | bidirectional | General-purpose I/O 78 with muxed digital peripheral functions. |
| 115 | GPIO79 | bidirectional | General-purpose I/O 79 with muxed digital peripheral functions. |
| 116 | GPIO80 | bidirectional | General-purpose I/O 80 with muxed digital peripheral functions. |
| 117 | GPIO81 | bidirectional | General-purpose I/O 81 with muxed digital peripheral functions. |
| 118 | GPIO5 | bidirectional | General-purpose I/O 5 with muxed digital peripheral functions. |
| 119 | GPIO9 | bidirectional | General-purpose I/O 9, a 5-V fail-safe tolerant pin. |
| 120 | GPIO61 | bidirectional | General-purpose I/O 61 with muxed digital peripheral functions. |
| 121 | GPIO59 | bidirectional | General-purpose I/O 59 with muxed digital peripheral functions. |
| 122 | GPIO10 | bidirectional | General-purpose I/O 10 with muxed digital peripheral functions. |
| 123 | GPIO34 | bidirectional | General-purpose I/O 34 with muxed digital peripheral functions. |
| 124 | GPIO15 | bidirectional | General-purpose I/O 15 with muxed digital peripheral functions. |
| 125 | GPIO14 | bidirectional | General-purpose I/O 14 with muxed digital peripheral functions. |
| 126 | GPIO6 | bidirectional | General-purpose I/O 6 with muxed digital peripheral functions. |
| 127 | GPIO30 | bidirectional | General-purpose I/O 30 with muxed digital peripheral functions. |
| 128 | GPIO31 | bidirectional | General-purpose I/O 31 with muxed digital peripheral functions. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | TQFP-128(14x14) |
| Category | |
| Pins | 128 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VDD supply voltage with respect to VSS | VDD | -0.3 | 1.5 | V | 68 | ||
| VDDIO supply voltage with respect to VSS | VDDIO | -0.3 | 4.6 | V | 68 | ||
| VDDA supply voltage with respect to VSSA | VDDA | -0.3 | 4.6 | V | 68 | ||
| Input voltage (3.3 V) | VIN | -0.3 | 4.6 | V | 68 | ||
| Input voltage (5.0 V) | VIN | -0.3 | 6 | V | GPIO2, GPIO3, GPIO9, GPIO32 only | 68 | |
| Output voltage | VO | -0.3 | 4.6 | V | 68 | ||
| Input clamp current per pin | IIK | -20 | 20 | mA | VIN < VSS/VSSA, VIN > VDDIO/VDDA | 68 | |
| Input clamp current total for all inputs | IIKTOTAL | -20 | 20 | mA | VIN < VSS/VSSA, VIN > VDDIO/VDDA | 68 | |
| Digital output current per pin | IOUT | -20 | 20 | mA | 68 | ||
| Operating junction temperature | TJ | -40 | 155 | °C | 68 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 68 | ||
| Device supply voltage VDDIO and VDDA, internal BOR disabled | VDDIO, VDDA | 2.8 | 3.3 | 3.63 | V | Internal BOR disabled | 71 |
| Device supply voltage VDDIO and VDDA, internal BOR enabled | VDDIO, VDDA | 3.3 | 3.63 | V | Internal BOR enabled; min is VBOR-VDDIO(MAX) + VBOR-GB | 71 | |
| Device supply voltage VDD | VDD | 1.14 | 1.2 | 1.32 | V | 71 | |
| Digital input voltage | VIN | -0.3 | V | VSS, 0.3 to VDDIO + 0.3 | 71 | ||
| Digital input voltage GPIO2, 3, 9, 32 | VIN | -0.3 | 5.5 | V | VSS, 0.3 to 5.5 | 71 | |
| Junction temperature | TJ | -40 | 150 | °C | 71 | ||
| Free-air temperature | TA | -40 | 125 | °C | 71 | ||
| Junction-to-case thermal resistance | RΘJC | 10.6 | °C/W | PDT package | 82 | ||
| Junction-to-board thermal resistance | RΘJB | 24.9 | °C/W | PDT package | 82 | ||
| Junction-to-free air thermal resistance | RΘJA | 42.5 | °C/W | PDT package, High k PCB | 82 | ||
| Junction-to-package top | PsiJT | 0.4 | °C/W | PDT package | 82 | ||
| Junction-to-board | PsiJB | 24.4 | °C/W | PDT package | 82 | ||
| High-level output impedance | ROH | 50 | 66 | 96 | Ω | VOH=VDDS-0.4V | 79 |
| Low-level output impedance | ROL | 48 | 60 | 84 | Ω | VOL=0.4V | 79 |
| Low-level output impedance GPIO2/3/9/32, DRVSELGPIOx = 1 | ROL | 15 | 21 | 33 | Ω | IO_DRVSEL:DRVSELGPIOx = 1 | 79 |
| Weak pulldown resistance | RPULLDOWN | 22 | 31 | 62 | kΩ | 79 | |
| Weak pullup resistance | RPULLUP | 19 | 29 | 54 | kΩ | 79 | |
| Weak pullup resistance GPIO2/3/9/32 | RPULLUP | 20 | 31 | 65 | kΩ | GPIO2/3/9/32 | 79 |
| High-level input voltage | VIH | 2 | V | 79 | |||
| High-level input voltage GPIO 23/41 | VIH | 2.21 | V | 79 | |||
| High-level input voltage GPIO2/3/9/32 | VIH | 1.35 | V | IO_MODSEL:MODSELGPIOx = 1 | 79 | ||
| Low-level input voltage | VIL | 0.8 | V | 79 | |||
| Low-level output voltage | VOL | 0.4 | V | IOL = IOL MAX | 79 | ||
| Low-level output voltage | VOL | 0.2 | V | IOL = 100 µA | 79 | ||
| Pin leakage digital inputs | ILEAK | 0.15 | µA | Pullups and outputs disabled, 0 V ≤ VIN ≤ VDDIO | 80 | ||
| Internal voltage regulator output | VVREG | 1.152 | 1.2 | 1.248 | V | 92 | |
| VDDIO BOR voltage on ramp down after XRSn release | VBOR-VDDIO-DOWN | 2.81 | 3 | V | After XRSn Release | 92 | |
| VDDIO Power on Reset Voltage | VPOR-VDDIO | 2.3 | V | Before and After XRSn Release | 92 | ||
| Supply ramp rate of 3.3V rails | SRVDD33 | 20 | 100 | mV/us | 92 | ||
| Frequency, device (system) clock | f(SYSCLK) | 2 | 150 | MHz | 100 | ||
| Frequency, INTOSC1 and INTOSC2 | fINTOSC | 9.82 | 10 | 10.1 | MHz | -40°C to 125°C | 108 |
| VDDIO current, operating | IDDIO | 92 | mA | VREG enabled, operating mode, 30 ℃ | 72 | ||
| VDDIO current, operating | IDDIO | 115 | mA | VREG enabled, operating mode, 125 ℃ | 72 | ||
| VDDA current, operating | IDDA | 14 | mA | VREG enabled, operating mode, 125 ℃ | 72 | ||
| VDDIO current during flash erase/program | IDDIO | 91 | 128 | mA | VREG enabled, Flash erase/program | 73 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| housing | PCT | ADC_RESULT_REGS ADCERESULT_BASE 0x0000_1A00 YES YES YES - PCTRACE_BUFFER_REGS ERAD_PCTRACE_BUFFER_BASE 0x0005_FE00 YES - - YES | 218 |
CAD (KiCad official)
- Symbol:
F28P550SJ9PDTR - Footprint:
Package_QFP:TQFP-128_14x14mm_P0.4mm - 3D model: TQFP-128(14x14) (KiCad packages3D, STEP)
- 3D model files:
f28p550sj9pdtr-etched.step/f28p550sj9pdtr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);f28p550sj9pdtr.step/f28p550sj9pdtr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (296 pp, sha256
573b9b30c44461b6, retrieved 2026-11-12, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).