component
F0424NTGK8
Public Made by Adomby adom
RENESAS RF Amplifiers, DFN-8-EP(2x2). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownF0424NTGK8
RENESAS · RF Amplifiers · DFN-8-EP(2x2)
F0424NTGK8 from RENESAS, in a DFN-8-EP(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VCC | power_in | Power supply for the amplifier, which must be bypassed with a capacitor placed as close to the pin as possible; the datasheet gives a VCC pin range of 3.15 V to 5.25 V. |
| 2 | RFIN | input | RF input internally matched to 50 Ω, and an external DC block is required. |
| 3 | NC | unconnected | No connection; the pin can be left unconnected, tied to VCC, or tied to GND, and IDT recommends connecting it to GND. |
| 4 | RSET | passive | Main amplifier current bias setting resistor pin, which must be connected to GND. |
| 5 | RDSET | passive | Distortion amplifier current bias setting resistor pin, which must be connected to GND. |
| 6 | STBY | input | Standby control: logic LOW or unconnected gives normal operation, logic HIGH puts the device in STBY mode, with logic input high threshold VIH of 1.07 V and low threshold VIL of 0.8 V. |
| 7 | RFOUT | output | RF output internally matched to 50 Ω, and an external DC block is required. |
| 8 | i.c. | passive | Internally connected pin that must be connected directly to ground. |
| 9 | EPAD | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | RENESAS |
| Package | DFN-8-EP(2x2) |
| Category | RF & Radio |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Power Supply Voltage | VCC | 3.15 | 5.25 | V | VCC pins | 6 | |
| Operating Temperature Range (exposed paddle) | TEPAD | -40 | 105 | °C | Exposed paddle temperature | 6 | |
| RF Frequency Range | fRF | 600 | 5000 | MHz | Operating range | 6 | |
| VCC to GND | VCC | -0.3 | 5.5 | V | 6 | ||
| STBY | VSTBY | -0.3 | 3.6 | V | 6 | ||
| STBY Minus VCC Voltage (voltage difference) | VSTBY-VCC | 0.3 | V | 6 | |||
| RFIN Externally Applied DC Current | IRFIN | -1 | 1 | mA | 6 | ||
| RSET Pin Maximum DC Current | IPIN4 | -1 | 1 | mA | 6 | ||
| RDSET Pin Maximum DC Current | IPIN5 | -1 | 1 | mA | 6 | ||
| RF Input Power (RFOUT) Maximum | PMAX_IN | 20 | dBm | Present for 24 Hours | 6 | ||
| Continuous Power Dissipation | PDISS | 0.6 | W | 6 | |||
| Junction Temperature | TJMAX | 140 | °C | 6 | |||
| Storage Temperature Range | TSTOR | -65 | 150 | °C | 6 | ||
| Lead Temperature | 260 | °C | Soldering, 10s | 6 | |||
| Electrostatic Discharge, HBM | 2000 | V | JEDEC/ESDA JS-001-2012 (Class 2) | 6 | |||
| Electrostatic Discharge, CDM | 1000 | V | JEDEC 22-C101F (Class C3) | 6 | |||
| Junction-to-Ambient Thermal Resistance | θJA | 93 | °C/W | 9 | |||
| Junction-to-Case Thermal Resistance (case = exposed paddle) | θJC-BOT | 27 | °C/W | Case is defined as the exposed paddle | 9 | ||
| Logic Input High Threshold (5V supply) | VIH | 1.07 | V | 7 | |||
| Logic Input Low Threshold (5V supply) | VIL | 0.8 | V | 7 | |||
| Logic Current (5V supply) | IIH, IIL | -10 | 100 | µA | Applied STBY voltage = 3.6V | 7 | |
| Supply Current (5V supply) | ICC | 70 | 80 | mA | 7 | ||
| Standby Current (5V supply) | ICC_STBY | 2 | 3 | mA | 7 | ||
| Settling Time (5V supply) | tSETTLE | 0.25 | µs | 50% STBY control to within ±0.5dB of final power level | 7 | ||
| RF Input Return Loss (5V supply) | RLIN | 13 | dB | 7 | |||
| RF Output Return Loss (5V supply) | RLOUT | 12 | dB | 7 | |||
| Gain (5V supply) | G | 16 | 17.3 | dB | fRF = 2600MHz | 7 | |
| Gain Flatness (5V supply) | GVAR | -0.15 | 0.15 | dB | fRF = 700MHz, ±100MHz | 7 | |
| Gain Flatness (5V supply) | GVAR | -0.1 | 0.1 | dB | fRF = 1900MHz, ±100MHz | 7 | |
| Gain Flatness (5V supply) | GVAR | -0.19 | 0.19 | dB | fRF = 4900MHz, ±100MHz | 7 | |
| Gain Variation over Temperature (5V supply) | GTEMP | -0.2 | 0.2 | dB | TEPAD = -40°C to +105°C | 7 | |
| Noise Figure (5V supply) | NF | 2.3 | 2.7 | dB | fRF = 2600MHz | 7 | |
| Noise Figure Variation over Temperature (5V supply) | NFTEMP | -0.4 | 0.4 | dB | TEPAD = -40°C to +105°C | 7 | |
| Output Third-Order Intercept Point (5V supply) | OIP3 | 35 | 40 | dBm | fRF = 2600MHz, 5MHz tone separation | 7 | |
| Output Third-Order Intercept Point Variation over Temperature (5V supply) | OIP3VAR | -1.2 | 0.26 | dB | fRF = 2600MHz, 5MHz tone separation, TEPAD = -40°C to +105°C | 7 | |
| Output P1dB Compression (5V supply) | OP1dB | 20 | 21 | dBm | fRF = 2600MHz | 8 | |
| Output P1dB Compression (5V supply) | OP1dB | 20 | dBm | fRF = 3500MHz | 8 | ||
| Output P1dB Compression (5V supply) | OP1dB | 18 | dBm | fRF = 4900MHz | 8 | ||
| Reverse Isolation (5V supply) | REVISO | 24 | dB | 8 | |||
| Logic Input High Threshold (3.3V supply) | VIH | 1.07 | V | 8 | |||
| Logic Input Low Threshold (3.3V supply) | VIL | 0.8 | V | 8 | |||
| Logic Current (3.3V supply) | IIH, IIL | -10 | 100 | µA | Applied STBY voltage = 3.6V | 8 | |
| Settling Time (3.3V supply) | tSETTLE | 0.25 | µs | 50% STBY control to within ±0.5dB of final power level | 8 | ||
| RF Input Return Loss (3.3V supply) | RLIN | 13 | dB | 8 | |||
| RF Output Return Loss (3.3V supply) | RLOUT | 12 | dB | 8 | |||
| Gain Flatness (3.3V supply) | GVAR | -0.15 | 0.15 | dB | fRF = 700MHz, ±100MHz | 8 | |
| Gain Flatness (3.3V supply) | GVAR | -0.1 | 0.1 | dB | fRF = 1900MHz, ±100MHz | 8 | |
| Gain Flatness (3.3V supply) | GVAR | -0.2 | 0.2 | dB | fRF = 3500MHz, ± 100MHz | 8 | |
| Gain Flatness (3.3V supply) | GVAR | -0.17 | 0.17 | dB | fRF = 4900MHz, ± 100MHz | 8 | |
| Gain Variation over Temperature (3.3V supply) | GTEMP | -0.2 | 0.2 | dB | TEPAD = -40°C to +105°C | 8 | |
| Noise Figure Variation over Temperature (3.3V supply) | NFTEMP | -0.4 | 0.5 | dB | TEPAD = -40°C to +105°C | 9 | |
| Reverse Isolation (3.3V supply) | REVISO | 24 | dB | 9 | |||
| Supply Current (3.3V supply) | ICC | 70 | mA | 8 | |||
| Standby Current (3.3V supply) | ICC_STBY | 2 | mA | 8 | |||
| Pull-down Resistor on STBY pin (5V supply) | RSTBY | 50 | kΩ | 7 |
CAD (KiCad official)
- Symbol:
F0424NTGK8 - Footprint:
Package_DFN_QFN:DFN-8-1EP_2x2mm_P0.5mm_EP0.6x1.2mm - 3D model: DFN-8-EP(2x2), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.75 mm tall, datasheet A, nominal). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
f0424ntgk8-etched.step/f0424ntgk8-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);f0424ntgk8.step/f0424ntgk8.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: RENESAS datasheet (24 pp, sha256
f9af2136073c4acf, retrieved 2026-11-12, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).