component

ET60S-S03-5-05-000-S-R1-S

Public Made by Adom

by adom

Samtec Samtec ET60S series board connector (R1 right-angle), Samtec_ET60S-S03-5-05-000-S-R1-S. KiCad symbol, footprint and 3D as used on Adom boards; pin functions from the manufacturer datasheet.

componentconnectorset60s-s03-5-05-000-s-r1-sboard-derived

Verified ET60S-S03-5-05-000-S-R1-S

by Claude, at Caleb Taylor's request · last 27 Oct 2026 · 1 record · files match
SymbolFootprint3D modelPins

Verification log 4 records

27 Oct 2026Claude, at Caleb Taylor's requestValidated against Samtec ET60S print Revision S and recommended PCB layout ET60S-XXX-X-XX-XXX-X-RX-X-FOOTPRINT Revision Jfiles match
SymbolFootprint3D modelPinsfor all variants
  • ✓Datasheet: the page already carries Samtec's current ET60S print (Revision S, sheet date 9/4/2023); sha256 1235d0e5 matches suddendocs.samtec.com/prints/et60s-xxx-x-xx-xxx-x-rx-x-mkt.pdf fetched 2026-10-27. Recommended layout checked against et60s-xxx-x-xx-xxx-x-rx-x-footprint.pdf Revision J (sheets 1, 3, 8)
  • ✓Part number decoded from the sheet 1 callout: S03 = split power, 3 positions, on the right; 5 signal rows; 05 positions per row; 000 = no power on the left; S = 30 µin gold; R1 = tail for .062 in PCB; S = side guide post
  • ✓Signal numbering per Fig 4 (p.3) and footprint Fig 4: 01 at the right end of the row nearest the board front edge, right to left, rows away from the edge (03 / 15 labels). Footprint pads 1-25 follow exactly that order (pad 1 at x -7.27, y 3.10 nearest the edge). Renamed signal pins from the board symbol's 31-55 to the drawing's 01-25
  • •Power: Fig 16 (p.10) and footprint Fig 14 show split power positions P01-P03 right of the signal block, P01 outermost, each with two tail columns 3.50 mm apart and 5 tails per column (10 PTH per position, footprint note 2). Pads P1_x/P2_x/P3_x renamed from 1-30 to P01/P02/P03; the ET60S print does not name the two halves of a split position (the mating ET60T print calls them P01L/P01R), so both columns carry the position name and the description says which column
  • ✓Pin types: all passive (connector contacts); power tails were power_in
  • ✓Footprint vs recommended layout: signal 5 x 5 at 2.00 mm pitch, drill 0.70 (Samtec 0.70 +-0.05 finished PTH), pad 1.00 vs Samtec 0.93 annular ring; power tails drill 1.02 (Samtec 1.02 +-0.05 PTH), pad 1.53 vs 1.25, rows at 2.50 mm, columns 3.50 mm apart, positions 8.00 mm apart (F = 19.50 for -03); left peg to first signal column 5.94, signal block to P03 5.27, P01 to right peg 5.50, peg centreline to the signal row nearest the edge 5.60, peg centreline on the middle power row: all match
  • ✓3D body 51.21 x 25.22 x 14.48 mm against the print: envelope 3.68 REF left of the left peg and 3.32 REF right of the right peg (51.21), depth 25.22 REF, 10.00 above the board plus 4.48 below (14.48); front face 19.57 mm from the peg centreline vs 9.32 + 10.31 REF = 19.63; Z-up, on the footprint origin
  • •Orderability: the footprint drawing (Rev J, note 5) marks split power -01/-02/-03 as not tooled, and print Rev S note 3 limits split power to the SUB-ET60S-01-X-RXX-SP option; DigiKey and Mouser do not list this configuration
  • ✓Symbol and footprint Datasheet properties point at the manufacturer datasheet URL
  • ✓Guide-post holes set to Samtec's 3.20 mm NPTH (2 places, ET60S recommended PCB layout rev J); the source board used 3.40 mm
  • ✓Symbol Datasheet / MPN / Manufacturer / DigiKey / Mouser / LCSC properties agree with page.json; footprint Datasheet property points at the manufacturer datasheet URL
  • ✓component-page-verify: all checks pass
Evidenceproduct print (Samtec)recommended PCB layout (Samtec)
Verified files✓ et60s-s03-5-05-000-s-r1-s.kicad_sym✓ et60s-s03-5-05-000-s-r1-s.kicad_mod✓ et60s-s03-5-05-000-s-r1-s.step
9 Oct 2026Claude (AI build)Datasheet pins not matched to a symbol pin: SP1_LEFT, SP2_LEFT, SP3_LEFTsuperseded
reviewfor all variants
  • •Datasheet pins not matched to a symbol pin: SP1_LEFT, SP2_LEFT, SP3_LEFT
9 Oct 2026Claude (AI build)Datasheet is the Samtec ET60S series print, not a part-specific drawing; confirm the S03-5...superseded
reviewfor all variants
  • •Datasheet is the Samtec ET60S series print, not a part-specific drawing; confirm the S03-5-05-000-S-R1-S options against its ordering tables.
9 Oct 2026Claude (AI build)Automated build checks (awaiting human validation)superseded
SymbolFootprint3D modelPinsfor all variants
  • ✓Footprint extracted pad-for-pad from the source board and normalized to the footprint frame (back-side parts un-mirrored)
  • ✓3D model seated z=0 at footprint origin (placement inverse; method centroid-matched to KiCad library models on 59 cases)
  • ✓adom-lbr generate + lint passed
  • ✓55 of 55 pins described from the datasheet (adom-ds2sf, page-cited)
  • •Not yet checked by a person: land pattern vs datasheet, pin-1/orientation, 3D body vs drawing
Evidencedatasheet
Verified files! et60s-s03-5-05-000-s-r1-s.kicad_sym! et60s-s03-5-05-000-s-r1-s.kicad_mod✓ et60s-s03-5-05-000-s-r1-s.step
Spot something wrong? Report it as an issue Propose a fix Records are signed by members of adom.
Overview Files Discover Packages Releases Dependencies Issues Breadcrumbs Pull Requests Activity
main
Download ZIP Propose a change
Generated by board-derived · KiCad file format 20241209
Name Last commit message Last updated
docs Licensed 3D model, datasheet text layer and verification log · Caleb 19d ago
et60s-s03-5-05-000-s-r1-s-hero.glb Publish 0.1.3 · Caleb 1d ago
et60s-s03-5-05-000-s-r1-s-hero.overlay.json Publish 0.1.3 · Caleb 1d ago
et60s-s03-5-05-000-s-r1-s.glb Licensed 3D model, datasheet text layer and verification log · Caleb 19d ago
et60s-s03-5-05-000-s-r1-s.kicad_mod Publish 0.1.3 · Caleb 1d ago
et60s-s03-5-05-000-s-r1-s.kicad_sym Publish 0.1.4 · Caleb 22h ago
et60s-s03-5-05-000-s-r1-s.lbr Publish 0.1.3 · Caleb 1d ago
et60s-s03-5-05-000-s-r1-s.step Licensed 3D model, datasheet text layer and verification log · Caleb 19d ago
package.json Publish 0.1.4 · Caleb 22h ago
page.json Set visibility: public · Caleb 22h ago
README.md Publish 0.1.1 · Caleb 1d ago
verification.json Publish 0.1.4 · Caleb 22h ago

ET60S-S03-5-05-000-S-R1-S

Samtec · Samtec ET60S series board connector (R1 right-angle) · Samtec_ET60S-S03-5-05-000-S-R1-S

ET60S-S03-5-05-000-S-R1-S from Samtec, in a Samtec_ET60S-S03-5-05-000-S-R1-S. Symbol, footprint and 3D model are the ones used on Adom board designs (3D model: Adom-generated 3D model built from the datasheet dimensions (simplified; CC-BY-SA 4.0); no vendor CAD is redistributed). Pin functions are extracted from the manufacturer datasheet with page references.

Pinout

Pin Name Type Function
1 01 passive Signal contact 01; numbering per the manufacturer drawing: 5 rows x 5 positions at 2.00 mm pitch, 01 at the right end of the row nearest the board front edge, counting right to left along each row and then row by row away from the edge (Fig 4). [datasheet p.3]
2 02 passive Signal contact 02; numbering per the manufacturer drawing. [datasheet p.3]
3 03 passive Signal contact 03; numbering per the manufacturer drawing. [datasheet p.3]
4 04 passive Signal contact 04; numbering per the manufacturer drawing. [datasheet p.3]
5 05 passive Signal contact 05; numbering per the manufacturer drawing. [datasheet p.3]
6 06 passive Signal contact 06; numbering per the manufacturer drawing. [datasheet p.3]
7 07 passive Signal contact 07; numbering per the manufacturer drawing. [datasheet p.3]
8 08 passive Signal contact 08; numbering per the manufacturer drawing. [datasheet p.3]
9 09 passive Signal contact 09; numbering per the manufacturer drawing. [datasheet p.3]
10 10 passive Signal contact 10; numbering per the manufacturer drawing. [datasheet p.3]
11 11 passive Signal contact 11; numbering per the manufacturer drawing. [datasheet p.3]
12 12 passive Signal contact 12; numbering per the manufacturer drawing. [datasheet p.3]
13 13 passive Signal contact 13; numbering per the manufacturer drawing. [datasheet p.3]
14 14 passive Signal contact 14; numbering per the manufacturer drawing. [datasheet p.3]
15 15 passive Signal contact 15; numbering per the manufacturer drawing. [datasheet p.3]
16 16 passive Signal contact 16; numbering per the manufacturer drawing. [datasheet p.3]
17 17 passive Signal contact 17; numbering per the manufacturer drawing. [datasheet p.3]
18 18 passive Signal contact 18; numbering per the manufacturer drawing. [datasheet p.3]
19 19 passive Signal contact 19; numbering per the manufacturer drawing. [datasheet p.3]
20 20 passive Signal contact 20; numbering per the manufacturer drawing. [datasheet p.3]
21 21 passive Signal contact 21; numbering per the manufacturer drawing. [datasheet p.3]
22 22 passive Signal contact 22; numbering per the manufacturer drawing. [datasheet p.3]
23 23 passive Signal contact 23; numbering per the manufacturer drawing. [datasheet p.3]
24 24 passive Signal contact 24; numbering per the manufacturer drawing. [datasheet p.3]
25 25 passive Signal contact 25; numbering per the manufacturer drawing. [datasheet p.3]
P1_1 P01 passive Split power position P01, outer tail column (the one farther from the signal block), tail 1 of 5 counted from the board front edge; the print labels the position P01 but does not name the two split halves. [datasheet p.10]
P1_2 P01 passive Split power position P01, outer tail column (the one farther from the signal block), tail 2 of 5 counted from the board front edge; the print labels the position P01 but does not name the two split halves. [datasheet p.10]
P1_3 P01 passive Split power position P01, outer tail column (the one farther from the signal block), tail 3 of 5 counted from the board front edge; the print labels the position P01 but does not name the two split halves. [datasheet p.10]
P1_4 P01 passive Split power position P01, outer tail column (the one farther from the signal block), tail 4 of 5 counted from the board front edge; the print labels the position P01 but does not name the two split halves. [datasheet p.10]
P1_5 P01 passive Split power position P01, outer tail column (the one farther from the signal block), tail 5 of 5 counted from the board front edge; the print labels the position P01 but does not name the two split halves. [datasheet p.10]
P1_6 P01 passive Split power position P01, inner tail column (the one nearer to the signal block), tail 1 of 5 counted from the board front edge; the print labels the position P01 but does not name the two split halves. [datasheet p.10]
P1_7 P01 passive Split power position P01, inner tail column (the one nearer to the signal block), tail 2 of 5 counted from the board front edge; the print labels the position P01 but does not name the two split halves. [datasheet p.10]
P1_8 P01 passive Split power position P01, inner tail column (the one nearer to the signal block), tail 3 of 5 counted from the board front edge; the print labels the position P01 but does not name the two split halves. [datasheet p.10]
P1_9 P01 passive Split power position P01, inner tail column (the one nearer to the signal block), tail 4 of 5 counted from the board front edge; the print labels the position P01 but does not name the two split halves. [datasheet p.10]
P1_10 P01 passive Split power position P01, inner tail column (the one nearer to the signal block), tail 5 of 5 counted from the board front edge; the print labels the position P01 but does not name the two split halves. [datasheet p.10]
P2_1 P02 passive Split power position P02, outer tail column (the one farther from the signal block), tail 1 of 5 counted from the board front edge; the print labels the position P02 but does not name the two split halves. [datasheet p.10]
P2_2 P02 passive Split power position P02, outer tail column (the one farther from the signal block), tail 2 of 5 counted from the board front edge; the print labels the position P02 but does not name the two split halves. [datasheet p.10]
P2_3 P02 passive Split power position P02, outer tail column (the one farther from the signal block), tail 3 of 5 counted from the board front edge; the print labels the position P02 but does not name the two split halves. [datasheet p.10]
P2_4 P02 passive Split power position P02, outer tail column (the one farther from the signal block), tail 4 of 5 counted from the board front edge; the print labels the position P02 but does not name the two split halves. [datasheet p.10]
P2_5 P02 passive Split power position P02, outer tail column (the one farther from the signal block), tail 5 of 5 counted from the board front edge; the print labels the position P02 but does not name the two split halves. [datasheet p.10]
P2_6 P02 passive Split power position P02, inner tail column (the one nearer to the signal block), tail 1 of 5 counted from the board front edge; the print labels the position P02 but does not name the two split halves. [datasheet p.10]
P2_7 P02 passive Split power position P02, inner tail column (the one nearer to the signal block), tail 2 of 5 counted from the board front edge; the print labels the position P02 but does not name the two split halves. [datasheet p.10]
P2_8 P02 passive Split power position P02, inner tail column (the one nearer to the signal block), tail 3 of 5 counted from the board front edge; the print labels the position P02 but does not name the two split halves. [datasheet p.10]
P2_9 P02 passive Split power position P02, inner tail column (the one nearer to the signal block), tail 4 of 5 counted from the board front edge; the print labels the position P02 but does not name the two split halves. [datasheet p.10]
P2_10 P02 passive Split power position P02, inner tail column (the one nearer to the signal block), tail 5 of 5 counted from the board front edge; the print labels the position P02 but does not name the two split halves. [datasheet p.10]
P3_1 P03 passive Split power position P03, outer tail column (the one farther from the signal block), tail 1 of 5 counted from the board front edge; the print labels the position P03 but does not name the two split halves. [datasheet p.10]
P3_2 P03 passive Split power position P03, outer tail column (the one farther from the signal block), tail 2 of 5 counted from the board front edge; the print labels the position P03 but does not name the two split halves. [datasheet p.10]
P3_3 P03 passive Split power position P03, outer tail column (the one farther from the signal block), tail 3 of 5 counted from the board front edge; the print labels the position P03 but does not name the two split halves. [datasheet p.10]
P3_4 P03 passive Split power position P03, outer tail column (the one farther from the signal block), tail 4 of 5 counted from the board front edge; the print labels the position P03 but does not name the two split halves. [datasheet p.10]
P3_5 P03 passive Split power position P03, outer tail column (the one farther from the signal block), tail 5 of 5 counted from the board front edge; the print labels the position P03 but does not name the two split halves. [datasheet p.10]
P3_6 P03 passive Split power position P03, inner tail column (the one nearer to the signal block), tail 1 of 5 counted from the board front edge; the print labels the position P03 but does not name the two split halves. [datasheet p.10]
P3_7 P03 passive Split power position P03, inner tail column (the one nearer to the signal block), tail 2 of 5 counted from the board front edge; the print labels the position P03 but does not name the two split halves. [datasheet p.10]
P3_8 P03 passive Split power position P03, inner tail column (the one nearer to the signal block), tail 3 of 5 counted from the board front edge; the print labels the position P03 but does not name the two split halves. [datasheet p.10]
P3_9 P03 passive Split power position P03, inner tail column (the one nearer to the signal block), tail 4 of 5 counted from the board front edge; the print labels the position P03 but does not name the two split halves. [datasheet p.10]
P3_10 P03 passive Split power position P03, inner tail column (the one nearer to the signal block), tail 5 of 5 counted from the board front edge; the print labels the position P03 but does not name the two split halves. [datasheet p.10]

Key specifications

Parameter Value
Manufacturer Samtec
Package Samtec_ET60S-S03-5-05-000-S-R1-S
Category Connectors
Pins 55

CAD

  • Symbol: et60s-s03-5-05-000-s-r1-s (source library Samtec_CDT:Samtec_ET60S-S03-5-05-000-S-R1-S)
  • Footprint: Samtec_CDT:Samtec_ET60S-S03-5-05-000-S-R1-S
  • 3D model path in footprint: ${KIPRJMOD}/et60s-s03-5-05-000-s-r1-s.step
  • 3D files: et60s-s03-5-05-000-s-r1-s.step / et60s-s03-5-05-000-s-r1-s.glb.
  • EAGLE/Fusion library: et60s-s03-5-05-000-s-r1-s.lbr (adom-lbr)

Provenance

  • Datasheet: Samtec ET60S-XXX-X-XX-XXX-X-RX-X product print (ET60S-XXX-X-XX-XXX-X-RX-X print, Revision S (sheet date 9/4/2023), sha256 1235d0e5868fafc7, retrieved 2026-10-27, tier: mfr)
  • CAD: Footprint and symbol as used on Adom board designs; 3D model: Adom-generated 3D model built from the datasheet dimensions (simplified; CC-BY-SA 4.0); no vendor CAD is redistributed.
  • Pins: KiCad symbol from the source board + adom-ds2sf datasheet extraction (claude-opus-4-7).

Datasheet PDF