main
Ray
Publish 0.1.0
2046d5d
ESP32-C61-WROOM-1-N8R2
Espressif Systems · RF and Wireless · 28-SMD Module
ESP32-C61-WROOM-1-N8R2 from Espressif Systems, in a 28-SMD Module. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Footprint from Espressif's KiCad libraries (CC-BY-SA 4.0); the 3D model is Espressif Systems's.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | Ground pin of the module. |
| 2 | 3V3 | power_in | Module power supply input; VDD33 is specified at 3.0 V min, 3.3 V typ, 3.6 V max, with absolute maximum −0.3 V to 3.6 V. |
| 3 | EN | input | Chip enable: high enables the chip and low powers it off; do not leave this pin floating. |
| 4 | IO4 | bidirectional | GPIO4 with alternate functions MTDI, LP_GPIO4, ADC1_CH2 and FSPIWP; MTDI is a strapping pin that defaults to floating at reset. |
| 5 | IO5 | bidirectional | GPIO5 with alternate functions MTCK, LP_GPIO5 and ADC1_CH3. |
| 6 | IO6 | bidirectional | GPIO6 with alternate functions MTDO, LP_GPIO6 and FSPICLK. |
| 7 | IO7 | bidirectional | GPIO7 with alternate function FSPID; GPIO7 is a JTAG source strapping pin that defaults to floating at reset. |
| 8 | IO0 | bidirectional | GPIO0 with alternate functions XTAL_32K_P and LP_GPIO0. |
| 9 | IO1 | bidirectional | GPIO1 with alternate functions XTAL_32K_N, LP_GPIO1 and ADC1_CH0. |
| 10 | IO8 | bidirectional | GPIO8 with alternate functions ZCD0 and FSPICS0; GPIO8 is a strapping pin (chip boot mode and ROM message printing) that defaults to floating at reset. |
| 11 | IO29 | bidirectional | GPIO29 general-purpose I/O. |
| 12 | NC/IO14 | bidirectional | Not connected on modules without PSRAM, where it can serve as GPIO14; on this PSRAM module it is used as SPICS1 for embedded SPI PSRAM and cannot be used for other functions. |
| 13 | IO12 | bidirectional | USB_D- (USB Serial/JTAG data) with GPIO12 function. |
| 14 | IO13 | bidirectional | USB_D+ (USB Serial/JTAG data) with GPIO13 function. |
| 15 | IO9 | bidirectional | GPIO9 with alternate function ZCD1; GPIO9 is a strapping pin with internal pull-up at reset and is the analog comparator test pad. |
| 16 | IO25 | bidirectional | GPIO25 with alternate function SDIO_CMD. |
| 17 | IO26 | bidirectional | GPIO26 with alternate function SDIO_CLK. |
| 18 | IO27 | bidirectional | GPIO27 with alternate function SDIO_DATA0. |
| 19 | IO28 | bidirectional | GPIO28 with alternate function SDIO_DATA1. |
| 20 | IO22 | bidirectional | GPIO22 with alternate function SDIO_DATA2. |
| 21 | IO23 | bidirectional | GPIO23 with alternate function SDIO_DATA3. |
| 22 | NC | unconnected | No connection. |
| 23 | IO24 | bidirectional | GPIO24 general-purpose I/O. |
| 24 | RX0 | bidirectional | UART0 receive (U0RXD) with GPIO10 function. |
| 25 | TX0 | bidirectional | UART0 transmit (U0TXD) with GPIO11 function; UART0 is used for firmware download and log output. |
| 26 | IO3 | bidirectional | GPIO3 with alternate functions MTMS, LP_GPIO3, ADC1_CH1 and FSPIHD; MTMS is a strapping pin that defaults to floating at reset. |
| 27 | IO2 | bidirectional | GPIO2 with alternate functions LP_GPIO2 and FSPIQ. |
| 28 | GND | power_in | Ground pin of the module. |
| 29 | EPAD | power_in | Exposed ground pad; soldering it to the base board ground is optional and improves thermal performance, using only the correct amount of solder paste. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Espressif Systems |
| Package | 28-SMD Module |
| Category | RF and Wireless |
| Pins | 29 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Power supply voltage | VDD33 | -0.3 | 3.6 | V | 25 | ||
| Power supply voltage | VDD33 | 3 | 3.3 | 3.6 | V | 25 | |
| Current delivered by external power supply | IVDD | 0.5 | A | 25 | |||
| Operating ambient temperature | TA | -40 | 85 | °C | 85 °C version | 25 | |
| Low-level input voltage | VIL | -0.3 | V | 25 | |||
| High-level input current | IIH | 50 | nA | 25 | |||
| Low-level input current | IIL | 50 | nA | 25 | |||
| Chip reset voltage | VIL_nRST | -0.3 | V | 25 | |||
| Flash power supply voltage (1.8 V) | VCC | 1.65 | 1.8 | 2 | V | Power supply voltage (1.8 V) | 27 |
| Flash power supply voltage (3.3 V) | VCC | 2.7 | 3.3 | 3.6 | V | Power supply voltage (3.3 V) | 27 |
| Flash maximum clock frequency | FC | 80 | MHz | Maximum clock frequency | 27 | ||
| Flash program/erase cycles | 100000 | cycles | Program/erase cycles | 27 | |||
| Flash data retention time | TRET | 20 | years | Data retention time | 27 | ||
| Flash page program time | TPP | 0.8 | 5 | ms | Page program time | 27 | |
| Flash sector erase time (4 KB) | TSE | 70 | 500 | ms | Sector erase time (4 KB) | 27 | |
| Flash block erase time (32 KB) | TBE1 | 0.2 | 2 | s | Block erase time (32 KB) | 27 | |
| Flash block erase time (64 KB) | TBE2 | 0.3 | 3 | s | Block erase time (64 KB) | 28 | |
| Flash chip erase time (64 Mb) | TCE | 25 | 100 | s | Chip erase time (64 Mb) | 28 | |
| PSRAM power supply voltage (1.8 V) | VCC | 1.62 | 1.8 | 1.98 | V | Power supply voltage (1.8 V) | 28 |
| PSRAM power supply voltage (3.3 V) | VCC | 2.7 | 3.3 | 3.6 | V | Power supply voltage (3.3 V) | 28 |
| PSRAM maximum clock frequency | FC | 80 | MHz | Maximum clock frequency | 28 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | tin | Solder: Sn-Ag-Cu (SAC305) lead-free solder Temperature (°C) | 44 |
CAD (land: Espressif; 3D: Espressif Systems)
- Symbol:
ESP32-C61-WROOM-1-N8R2 - Footprint:
PCM_Espressif:ESP32-C61-WROOM-1 - 3D model: 28-SMD Module (Espressif KiCad libraries, STEP)
- 3D model files:
esp32-c61-wroom-1-n8r2-etched.step/esp32-c61-wroom-1-n8r2-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);esp32-c61-wroom-1-n8r2.step/esp32-c61-wroom-1-n8r2.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Espressif Systems datasheet (48 pp, sha256
024a03c9db133d54, retrieved 2026-11-18) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: land: Espressif's KiCad libraries (CC-BY-SA 4.0); 3D: Espressif Systems's model.
# ESP32-C61-WROOM-1-N8R2
**Espressif Systems** · RF and Wireless · 28-SMD Module
ESP32-C61-WROOM-1-N8R2 from Espressif Systems, in a 28-SMD Module. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Footprint from Espressif's KiCad libraries (CC-BY-SA 4.0); the 3D model is Espressif Systems's.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | Ground pin of the module. |
| 2 | 3V3 | power_in | Module power supply input; VDD33 is specified at 3.0 V min, 3.3 V typ, 3.6 V max, with absolute maximum −0.3 V to 3.6 V. |
| 3 | EN | input | Chip enable: high enables the chip and low powers it off; do not leave this pin floating. |
| 4 | IO4 | bidirectional | GPIO4 with alternate functions MTDI, LP_GPIO4, ADC1_CH2 and FSPIWP; MTDI is a strapping pin that defaults to floating at reset. |
| 5 | IO5 | bidirectional | GPIO5 with alternate functions MTCK, LP_GPIO5 and ADC1_CH3. |
| 6 | IO6 | bidirectional | GPIO6 with alternate functions MTDO, LP_GPIO6 and FSPICLK. |
| 7 | IO7 | bidirectional | GPIO7 with alternate function FSPID; GPIO7 is a JTAG source strapping pin that defaults to floating at reset. |
| 8 | IO0 | bidirectional | GPIO0 with alternate functions XTAL_32K_P and LP_GPIO0. |
| 9 | IO1 | bidirectional | GPIO1 with alternate functions XTAL_32K_N, LP_GPIO1 and ADC1_CH0. |
| 10 | IO8 | bidirectional | GPIO8 with alternate functions ZCD0 and FSPICS0; GPIO8 is a strapping pin (chip boot mode and ROM message printing) that defaults to floating at reset. |
| 11 | IO29 | bidirectional | GPIO29 general-purpose I/O. |
| 12 | NC/IO14 | bidirectional | Not connected on modules without PSRAM, where it can serve as GPIO14; on this PSRAM module it is used as SPICS1 for embedded SPI PSRAM and cannot be used for other functions. |
| 13 | IO12 | bidirectional | USB_D- (USB Serial/JTAG data) with GPIO12 function. |
| 14 | IO13 | bidirectional | USB_D+ (USB Serial/JTAG data) with GPIO13 function. |
| 15 | IO9 | bidirectional | GPIO9 with alternate function ZCD1; GPIO9 is a strapping pin with internal pull-up at reset and is the analog comparator test pad. |
| 16 | IO25 | bidirectional | GPIO25 with alternate function SDIO_CMD. |
| 17 | IO26 | bidirectional | GPIO26 with alternate function SDIO_CLK. |
| 18 | IO27 | bidirectional | GPIO27 with alternate function SDIO_DATA0. |
| 19 | IO28 | bidirectional | GPIO28 with alternate function SDIO_DATA1. |
| 20 | IO22 | bidirectional | GPIO22 with alternate function SDIO_DATA2. |
| 21 | IO23 | bidirectional | GPIO23 with alternate function SDIO_DATA3. |
| 22 | NC | unconnected | No connection. |
| 23 | IO24 | bidirectional | GPIO24 general-purpose I/O. |
| 24 | RX0 | bidirectional | UART0 receive (U0RXD) with GPIO10 function. |
| 25 | TX0 | bidirectional | UART0 transmit (U0TXD) with GPIO11 function; UART0 is used for firmware download and log output. |
| 26 | IO3 | bidirectional | GPIO3 with alternate functions MTMS, LP_GPIO3, ADC1_CH1 and FSPIHD; MTMS is a strapping pin that defaults to floating at reset. |
| 27 | IO2 | bidirectional | GPIO2 with alternate functions LP_GPIO2 and FSPIQ. |
| 28 | GND | power_in | Ground pin of the module. |
| 29 | EPAD | power_in | Exposed ground pad; soldering it to the base board ground is optional and improves thermal performance, using only the correct amount of solder paste. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Espressif Systems |
| Package | 28-SMD Module |
| Category | RF and Wireless |
| Pins | 29 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Power supply voltage | VDD33 | -0.3 | | 3.6 | V | | 25 |
| Power supply voltage | VDD33 | 3 | 3.3 | 3.6 | V | | 25 |
| Current delivered by external power supply | IVDD | 0.5 | | | A | | 25 |
| Operating ambient temperature | TA | -40 | | 85 | °C | 85 °C version | 25 |
| Low-level input voltage | VIL | -0.3 | | | V | | 25 |
| High-level input current | IIH | | | 50 | nA | | 25 |
| Low-level input current | IIL | | | 50 | nA | | 25 |
| Chip reset voltage | VIL_nRST | -0.3 | | | V | | 25 |
| Flash power supply voltage (1.8 V) | VCC | 1.65 | 1.8 | 2 | V | Power supply voltage (1.8 V) | 27 |
| Flash power supply voltage (3.3 V) | VCC | 2.7 | 3.3 | 3.6 | V | Power supply voltage (3.3 V) | 27 |
| Flash maximum clock frequency | FC | 80 | | | MHz | Maximum clock frequency | 27 |
| Flash program/erase cycles | | 100000 | | | cycles | Program/erase cycles | 27 |
| Flash data retention time | TRET | 20 | | | years | Data retention time | 27 |
| Flash page program time | TPP | | 0.8 | 5 | ms | Page program time | 27 |
| Flash sector erase time (4 KB) | TSE | | 70 | 500 | ms | Sector erase time (4 KB) | 27 |
| Flash block erase time (32 KB) | TBE1 | | 0.2 | 2 | s | Block erase time (32 KB) | 27 |
| Flash block erase time (64 KB) | TBE2 | | 0.3 | 3 | s | Block erase time (64 KB) | 28 |
| Flash chip erase time (64 Mb) | TCE | | 25 | 100 | s | Chip erase time (64 Mb) | 28 |
| PSRAM power supply voltage (1.8 V) | VCC | 1.62 | 1.8 | 1.98 | V | Power supply voltage (1.8 V) | 28 |
| PSRAM power supply voltage (3.3 V) | VCC | 2.7 | 3.3 | 3.6 | V | Power supply voltage (3.3 V) | 28 |
| PSRAM maximum clock frequency | FC | 80 | | | MHz | Maximum clock frequency | 28 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | | tin | Solder: Sn-Ag-Cu (SAC305) lead-free solder Temperature (°C) | 44 |
## CAD (land: Espressif; 3D: Espressif Systems)
- Symbol: `ESP32-C61-WROOM-1-N8R2`
- Footprint: `PCM_Espressif:ESP32-C61-WROOM-1`
- 3D model: 28-SMD Module (Espressif KiCad libraries, STEP)
- 3D model files: `esp32-c61-wroom-1-n8r2-etched.step` / `esp32-c61-wroom-1-n8r2-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `esp32-c61-wroom-1-n8r2.step` / `esp32-c61-wroom-1-n8r2.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Espressif Systems datasheet](https://documentation.espressif.com/esp32-c61-wroom-1_wroom-1u_datasheet_en.pdf) (48 pp, sha256 `024a03c9db133d54`, retrieved 2026-11-18)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** land: Espressif's KiCad libraries (CC-BY-SA 4.0); 3D: Espressif Systems's model.
[Datasheet PDF](docs/esp32-c61-wroom-1-n8r2-datasheet.pdf)