component
EG4002A
Public Made by Adomby adom
EG Micro Human Body Sensing Sensor, SOP-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownEG4002A
EG Micro · Human Body Sensing Sensor · SOP-8
EG4002A from EG Micro, in a SOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | 1OUT | output | Output of the internal first-stage operational amplifier (OP1), with an absolute maximum of -0.3 V to 7 V relative to GND. |
| 2 | 1IN- | input | Inverting input of the internal first-stage operational amplifier, with an absolute maximum of -0.3 V to 7 V relative to GND. |
| 3 | VC | input | Trigger-inhibit input: when VC is below 0.2·VDD the OUT pin is held low and triggering is blocked, and when VC is above 0.2·VDD triggering is enabled. |
| 4 | A | input | Retriggerable/non-retriggerable control: A = '1' enables retriggering, and A = '0' selects non-retriggerable operation. |
| 5 | GND | power_in | Chip ground reference pin. |
| 6 | OUT | output | Active-high control signal output that sources or sinks +/-25 mA at VDD = 5 V and +/-10 mA at VDD = 3 V. |
| 7 | CT | input | Oscillator timing pin that requires an external capacitor to GND and a pull-up resistor to VDD, where the pull-up resistor must be greater than 100 kΩ. |
| 8 | VDD | power_in | Supply input with an operating range of +3 V to +6 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | EG Micro |
| Package | SOP-8 |
| Category | Sensors |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Vdd pin voltage relative to GND | VDD | -0.3 | 7 | V | 8 | ||
| OUT pin voltage relative to GND | OUT | -0.3 | 7 | V | 8 | ||
| CT pin voltage relative to GND | CT | -0.3 | 7 | V | 8 | ||
| A pin voltage relative to GND | A | -0.3 | 7 | V | 8 | ||
| VC pin voltage relative to GND (printed as FB pin) | VC | -0.3 | 7 | V | 8 | ||
| 1IN- pin voltage relative to GND | 1IN- | -0.3 | 7 | V | 8 | ||
| 1OUT pin voltage relative to GND | 1OUT | -0.3 | 7 | V | 8 | ||
| Ambient temperature | TA | -45 | 85 | ℃ | 8 | ||
| Storage temperature | Tstr | -65 | 125 | ℃ | 8 | ||
| Soldering temperature | TL | 300 | ℃ | T=10S | 8 | ||
| Operating supply voltage (Vdd pin input voltage) | VDD | 3 | 6 | V | 9 | ||
| Quiescent operating current | Icc | 65 | 75 | uA | Vdd=5V | 9 | |
| Quiescent operating current | Icc | 35 | 45 | uA | Vdd=3V | 9 | |
| Op-amp input offset voltage | Vos | 2 | 5 | mV | Vdd=5V | 9 | |
| Op-amp input offset current | Ios | 50 | nA | Vdd=5V | 9 | ||
| Op-amp open-loop voltage gain | Avo | 60 | dB | Vdd=5V | 9 | ||
| Op-amp output high level | VOPAH | 4.5 | 4.85 | V | Vdd=5V,ILOAD=5uA | 9 | |
| Op-amp output low level | VOPAL | 0.1 | V | Vdd=5V, ILOAD=-5uA | 9 | ||
| VC input high level | VCH | 1.1 | V | Vdd=5V | 9 | ||
| VC input high level | VCH | 0.7 | V | Vdd=3V | 9 | ||
| VC input low level | VCL | 0.4 | V | Vdd=5V | 9 | ||
| VC input low level | VCL | 0.3 | V | Vdd=3V | 9 | ||
| OUT output high level | VOH | 4.5 | 4.6 | V | Vdd=5V, ILOAD=10mA | 9 | |
| OUT output high level | VOH | 2.5 | 2.6 | V | Vdd=3V, ILOAD=5mA | 9 | |
| OUT output low level | VOL | 0.3 | 0.5 | V | Vdd=5V, ILOAD=-10mA | 9 | |
| A pin input high level | VAH | 3.5 | 5 | V | Vdd=5V | 9 | |
| A pin input high level | VAH | 2 | 3 | V | Vdd=3V | 9 | |
| A pin input low level | VAL | 0 | 1 | V | Vdd=5V | 9 | |
| A pin input low level | VAL | 0 | 0.5 | V | Vdd=3V | 9 |
CAD (KiCad official)
- Symbol:
EG4002A - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOP-8 (KiCad packages3D, STEP)
- 3D model files:
eg4002a-etched.step/eg4002a-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);eg4002a.step/eg4002a.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: EG Micro datasheet (13 pp, sha256
b8900d329e8e5b7a, retrieved 2026-10-30, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).