main
Ray
Initial commit: component/e-l9823013tr
4183173
E-L9823013TR
STMicroelectronics · Power Distribution Switches · SO-24-300mil
E-L9823013TR from STMicroelectronics, in a SO-24-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OUT7 | output | Low-side driver output 7 with 0.5 A maximum capability and 50 V typical output clamp voltage for inductive load flyback suppression. |
| 2 | OUT6 | output | Low-side driver output 6 with 0.5 A maximum capability and 50 V typical output clamp voltage for inductive load flyback suppression. |
| 3 | SCLK | input | SPI clock input; 160 ns minimum low time; shifts data on falling edge into shift register and changes SO on rising edge. |
| 4 | SI | input | SPI serial data input; 8-bit instruction stream accepted on falling edge of SCLK with MSB first; logic level selects output on/off on CSB rising edge. |
| 5 | GND | power_in | Analog ground connection point. |
| 6 | GND | power_in | Analog ground connection point. |
| 7 | GND | power_in | Analog ground connection point. |
| 8 | GND | power_in | Analog ground connection point. |
| 9 | SO | tri_state | Tri-state SPI serial output reporting drain status; remains high-impedance until CSB goes low; changes state on rising SCLK edge with 100 ns maximum propagation delay. |
| 10 | CSB | input | Active-low chip select input enabling SPI communication; latches output control data on rising edge; must transition only when SCLK is low. |
| 11 | OUT5 | output | Low-side driver output 5 with 0.5 A maximum capability and 50 V typical output clamp voltage for inductive load flyback suppression. |
| 12 | OUT4 | output | Low-side driver output 4 with 0.5 A maximum capability and 50 V typical output clamp voltage for inductive load flyback suppression. |
| 13 | OUT3 | output | Low-side driver output 3 with 0.5 A maximum capability and 50 V typical output clamp voltage for inductive load flyback suppression. |
| 14 | OUT2 | output | Low-side driver output 2 with 0.5 A maximum capability and 50 V typical output clamp voltage for inductive load flyback suppression. |
| 15 | SFPD | input | Short Fault Protect Disable control input; VDD-tied enables current limiting mode on overcurrent; GND-tied enables immediate latch-off shutdown on overcurrent. |
| 16 | VDD | power_in | Single supply voltage input; 4.5 V to 5.5 V nominal operation with 2.5 V to 3.95 V undervoltage reset threshold. |
| 17 | GND | power_in | Analog ground connection point. |
| 18 | GND | power_in | Analog ground connection point. |
| 19 | GND | power_in | Analog ground connection point. |
| 20 | GND | power_in | Analog ground connection point. |
| 21 | N.C. | unconnected | No internal connection. |
| 22 | RESET | input | Active-low asynchronous reset input clearing SPI shift register and turning all outputs off; requires 160 ns minimum low pulse; includes internal pull-down. |
| 23 | OUT1 | output | Low-side driver output 1 with 0.5 A maximum capability and 50 V typical output clamp voltage for inductive load flyback suppression. |
| 24 | OUT0 | output | Low-side driver output 0 with 0.5 A maximum capability and 50 V typical output clamp voltage for inductive load flyback suppression. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | SO-24-300mil |
| Category | Power Supply Chip |
| Pins | 24 |
CAD (KiCad official)
- Symbol:
E-L9823013TR - Footprint:
Package_SO:SO-24_5.3x15mm_P1.27mm - 3D model: SO-24-300mil, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.75 mm nominal SOIC height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
- 3D model files:
e-l9823013tr-etched.step/e-l9823013tr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);e-l9823013tr.step/e-l9823013tr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (19 pp, sha256
045398f1bc6a2a97, retrieved 2026-10-01, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.2, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# E-L9823013TR
**STMicroelectronics** · Power Distribution Switches · SO-24-300mil
E-L9823013TR from STMicroelectronics, in a SO-24-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OUT7 | output | Low-side driver output 7 with 0.5 A maximum capability and 50 V typical output clamp voltage for inductive load flyback suppression. |
| 2 | OUT6 | output | Low-side driver output 6 with 0.5 A maximum capability and 50 V typical output clamp voltage for inductive load flyback suppression. |
| 3 | SCLK | input | SPI clock input; 160 ns minimum low time; shifts data on falling edge into shift register and changes SO on rising edge. |
| 4 | SI | input | SPI serial data input; 8-bit instruction stream accepted on falling edge of SCLK with MSB first; logic level selects output on/off on CSB rising edge. |
| 5 | GND | power_in | Analog ground connection point. |
| 6 | GND | power_in | Analog ground connection point. |
| 7 | GND | power_in | Analog ground connection point. |
| 8 | GND | power_in | Analog ground connection point. |
| 9 | SO | tri_state | Tri-state SPI serial output reporting drain status; remains high-impedance until CSB goes low; changes state on rising SCLK edge with 100 ns maximum propagation delay. |
| 10 | CSB | input | Active-low chip select input enabling SPI communication; latches output control data on rising edge; must transition only when SCLK is low. |
| 11 | OUT5 | output | Low-side driver output 5 with 0.5 A maximum capability and 50 V typical output clamp voltage for inductive load flyback suppression. |
| 12 | OUT4 | output | Low-side driver output 4 with 0.5 A maximum capability and 50 V typical output clamp voltage for inductive load flyback suppression. |
| 13 | OUT3 | output | Low-side driver output 3 with 0.5 A maximum capability and 50 V typical output clamp voltage for inductive load flyback suppression. |
| 14 | OUT2 | output | Low-side driver output 2 with 0.5 A maximum capability and 50 V typical output clamp voltage for inductive load flyback suppression. |
| 15 | SFPD | input | Short Fault Protect Disable control input; VDD-tied enables current limiting mode on overcurrent; GND-tied enables immediate latch-off shutdown on overcurrent. |
| 16 | VDD | power_in | Single supply voltage input; 4.5 V to 5.5 V nominal operation with 2.5 V to 3.95 V undervoltage reset threshold. |
| 17 | GND | power_in | Analog ground connection point. |
| 18 | GND | power_in | Analog ground connection point. |
| 19 | GND | power_in | Analog ground connection point. |
| 20 | GND | power_in | Analog ground connection point. |
| 21 | N.C. | unconnected | No internal connection. |
| 22 | RESET | input | Active-low asynchronous reset input clearing SPI shift register and turning all outputs off; requires 160 ns minimum low pulse; includes internal pull-down. |
| 23 | OUT1 | output | Low-side driver output 1 with 0.5 A maximum capability and 50 V typical output clamp voltage for inductive load flyback suppression. |
| 24 | OUT0 | output | Low-side driver output 0 with 0.5 A maximum capability and 50 V typical output clamp voltage for inductive load flyback suppression. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | SO-24-300mil |
| Category | Power Supply Chip |
| Pins | 24 |
## CAD (KiCad official)
- Symbol: `E-L9823013TR`
- Footprint: `Package_SO:SO-24_5.3x15mm_P1.27mm`
- 3D model: SO-24-300mil, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.75 mm nominal SOIC height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
- 3D model files: `e-l9823013tr-etched.step` / `e-l9823013tr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `e-l9823013tr.step` / `e-l9823013tr.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [STMicroelectronics datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588884732355989504) (19 pp, sha256 `045398f1bc6a2a97`, retrieved 2026-10-01, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/e-l9823013tr-datasheet.pdf)