D706TF

{
  "slug": "d706tf",
  "version": "0.1.0",
  "type": "component",
  "description": "Silicore(芯谷) , SOP-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",
  "tags": [
    "component",
    "ic",
    "d706tf",
    "factory-2.0.0",
    "extractor-text"
  ],
  "dependencies": {},
  "hero": {
    "type": "image",
    "path": "docs/hero.png"
  },
  "files": [
    "page.json",
    "README.md",
    "d706tf.kicad_sym",
    "d706tf.kicad_mod",
    "d706tf.glb",
    "d706tf.step",
    "d706tf.lbr",
    "docs/hero.png",
    "docs/d706tf-datasheet.pdf",
    "viewers/symbol.html",
    "viewers/footprint.html",
    "d706tf-hero.glb",
    "d706tf-hero.overlay.json",
    "d706tf-etched.glb"
  ],
  "component": {
    "mpn": "D706TF",
    "manufacturer": "Silicore(芯谷)",
    "package": "SOP-8",
    "pin_count": 8,
    "category": "IC",
    "subcategory": "IC",
    "datasheet": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8603145182149681152",
    "parts": {
      "symbol": "d706tf.kicad_sym",
      "footprint": "d706tf.kicad_mod",
      "model_3d": "d706tf-hero.glb",
      "model_3d_plain": "d706tf-etched.glb",
      "model_3d_step": "d706tf-etched.step",
      "model_3d_step_plain": "d706tf.step",
      "lbr": "d706tf.lbr"
    },
    "distributor_links": {
      "lcsc": "C5368845"
    },
    "distributor_check": {
      "checked_at": "2026-10-21T01:15:49Z",
      "source": "Component Ocean /api/assign-pns",
      "digikey": {
        "pn": null,
        "status": "no match"
      },
      "mouser": {
        "pn": null,
        "status": "no match"
      }
    },
    "pins": [
      {
        "number": "1",
        "name": "MR",
        "type": "input",
        "description": "Active-LOW manual reset input that triggers a reset pulse, with a 250µA pull-up (MR = 0V pull-up current 100 to 250 to 600 µA), VIH min 2.0 V and VIL max 0.8 V."
      },
      {
        "number": "2",
        "name": "VCC",
        "type": "power_in",
        "description": "+5V power supply input; operating voltage range 1.2 V to 5.5 V, and absolute maximum supply voltage is -0.3 V to +6.0 V."
      },
      {
        "number": "3",
        "name": "GND",
        "type": "power_in",
        "description": "Ground reference for all signals."
      },
      {
        "number": "4",
        "name": "PFI",
        "type": "input",
        "description": "Power-fail voltage monitor input; PFO goes low when PFI is below 1.25 V (1.20 to 1.30 V threshold), and PFI should be connected to ground or VCC when not used."
      },
      {
        "number": "5",
        "name": "PFO",
        "type": "output",
        "description": "Active-LOW power-fail output that sinks current when PFI is below 1.25 V, with VOL max 0.4 V at 3.2 mA sink."
      },
      {
        "number": "6",
        "name": "WDI",
        "type": "input",
        "description": "Watchdog input that controls the internal watchdog timer; transitions as short as 50 ns clear the timer, and the input threshold is VIH 3.5 V and VIL 0.8 V at VCC = 5 V."
      },
      {
        "number": "7",
        "name": "RESET",
        "type": "output",
        "description": "Active-LOW reset output that stays low while VCC is below the reset threshold (3.08 V for D706T) and remains low for the reset pulse width after VCC rises above the threshold or MR goes high."
      },
      {
        "number": "8",
        "name": "WDO",
        "type": "output",
        "description": "Watchdog output that pulls LOW when the 1.6 s watchdog timer times out and stays low while VCC is below the reset threshold, returning HIGH without delay once VCC exceeds the threshold."
      }
    ],
    "provenance": {
      "extractor": "extract_pins 0.3",
      "factory_chain": {
        "factory": "2.0.0",
        "extractor": "extract_pins 0.3",
        "primary_model": "claude-haiku-5-5",
        "primary_mode": "text",
        "consensus_model": "claude-sonnet-5-5",
        "consensus": "agreed",
        "guards": "pin_guards 0.1: passed",
        "guard_notes": [
          "extractor flagged: Pin numbers for SOP8 are taken from the 'DIP/SOP' column of the PIN DESCRIPTION table (page 2-3). Th; The part marking table (page 8) lists D706TF as the SOP8 marking for the 3.08 V threshold version, w; Datasheet timing conflicts: WDI section says a 2.4 s HIGH/LOW signal is needed while the watchdog ti"
        ],
        "pages_sent": 12,
        "cost_usd": 0.0424,
        "at": "2026-10-21T01:11:16"
      },
      "datasheet": {
        "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8603145182149681152",
        "pages": 12,
        "sha256": "446c69db8a7c2a24",
        "source_tier": "lcsc"
      },
      "cad": "KiCad official (CC-BY-SA 4.0)",
      "pins": {
        "total": 8,
        "described": 8,
        "cites_pages": true,
        "refuses_to_fabricate": true
      }
    },
    "viewers": {
      "symbol": "viewers/symbol.html",
      "footprint": "viewers/footprint.html"
    },
    "models_3d": [
      {
        "file": "d706tf.step",
        "role": "plain",
        "up": "Z",
        "units": "mm",
        "origin": "footprint origin = pad-pattern centre",
        "seat": "z = 0",
        "extents_mm": [
          6.0,
          4.9,
          1.75
        ],
        "zmin_mm": -0.0,
        "centre_offset_mm": 0.0,
        "footprint_binding": "identity",
        "sha256": "07f46cff378d30e6c27dfd5a03092c795323f86d91c71fc7e743f4f418dc553a",
        "checked": "2026-10-21",
        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
      },
      {
        "file": "d706tf-etched.step",
        "role": "eda",
        "up": "Z",
        "units": "mm",
        "origin": "footprint origin = pad-pattern centre",
        "seat": "z = 0",
        "extents_mm": [
          6.0,
          4.9,
          1.75
        ],
        "zmin_mm": -0.0,
        "centre_offset_mm": 0.0,
        "footprint_binding": "identity",
        "sha256": "df3863838b85427238d4695a02ff66ef9b06fd3f7dbf66f5063da8ebaf700741",
        "checked": "2026-10-21",
        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
      }
    ]
  }
}