3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownCYPD3177-24LQXQT
INFINEON TECHNOLOGIES · Power Management - Specialized · QFN-24(4x4)
CYPD3177-24LQXQT from INFINEON TECHNOLOGIES, in a QFN-24(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBUS_MIN | input | Connect a resistor divider to 3.3 V (from the VDDD pin) to indicate the minimum voltage the system needs from the attached power adapter; see Table 2 for resistor values. |
| 2 | VBUS_MAX | input | Connect a resistor divider to 3.3 V (from the VDDD pin) to indicate the maximum voltage the system needs from the attached power adapter; see Table 2 for resistor values. |
| 3 | VBUS_FET_EN | output | Slew-rate-controlled PMOS FET gate driver output, connected to the FET gate through a series resistor and enabled when a power contract is successfully negotiated within the requested range. |
| 4 | SAFE_PWR_EN | output | PMOS FET gate driver output, connected to the FET gate through a series resistor and enabled when the device fails to negotiate higher power and defaults to 5 V. |
| 5 | ISNK_COARSE | input | Connect a resistor divider to 3.3 V (from the VDDD pin) to set the operating current requested from the power adapter; see Tables 3 and 4 for resistor values. |
| 6 | ISNK_FINE | input | Connect a resistor divider to 3.3 V (from the VDDD pin) to set the operating current requested from the power adapter; see Tables 3 and 4 for resistor values. |
| 7 | HPI_INT | output | Active LOW HPI interrupt pin. |
| 8 | GPIO_1 | bidirectional | Additional GPIO that can be set up over the HPI interface. |
| 9 | FAULT | output | Pulled high by the device if the power adapter cannot supply the required voltage or current or if an OVP event is detected, and low otherwise. |
| 10 | FLIP | bidirectional | Open-drain I/O that needs an external pull-up; it is low when no device is attached or CC1 is connected and high when CC2 is connected, and a pull-up of 4.7 kΩ or less (or none) sets the UFP VDO data capability bit to 1, while 50 kΩ sets it to 0. |
| 11 | VDC_OUT | input | Connect to the output of the PFETs controlled by VBUS_FET_EN to monitor the VBUS output, which is the power output of the system. |
| 12 | HPI_SDA | bidirectional | I2C slave data line that lets a host processor control and monitor the device (slave address 0x08, up to 1 Mbps). |
| 13 | HPI_SCL | bidirectional | I2C slave clock line that lets a host processor control and monitor the device (slave address 0x08, up to 1 Mbps). |
| 14 | CC2 | bidirectional | Communication Channel 2 pin used to negotiate a voltage/current with the attached adapter, protected against VBUS shorts (17 V continuous). |
| 15 | CC1 | bidirectional | Communication Channel 1 pin used to negotiate a voltage/current with the attached adapter, protected against VBUS shorts (17 V continuous). |
| 16 | D- | unconnected | Leave this pin unconnected. |
| 17 | D+ | unconnected | Leave this pin unconnected. |
| 18 | VBUS_IN | power_in | Connect to VBUS of the USB Type-C connector; supplies the device (3.0 V to 24.5 V) and monitors incoming voltage. |
| 19 | GND | power_in | System ground pin. |
| 20 | DNU1 | unconnected | Do not use; leave this pin unconnected. |
| 21 | DNU2 | unconnected | Do not use; leave this pin unconnected. |
| 22 | VSS | power_in | Ground pin, connect to USB Type-C connector GND. |
| 23 | VDDD | power_out | Output of the internal 3.3-V regulator; connect 1 µF and 2x 100-nF capacitors. |
| 24 | VCCD | power_out | Output of the internal 1.8-V regulator; connect a 1-µF decoupling capacitor. |
| 25 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | INFINEON TECHNOLOGIES |
| Package | QFN-24(4x4) |
| Category | Power Management (PMIC) |
| Pins | 25 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Max supply voltage on VBUS_IN and VDC_OUT pins | VBUS_MAX | 30 | V | Absolute max | 11 | ||
| Max supply voltage relative to VSS | VDDD_MAX | 6 | V | 11 | |||
| Max voltage on CC1, CC2 pins | VCC_PIN_ABS | 22 | V | As per USB PD specification, maximum allowed VBUS = 21.5 V | 11 | ||
| GPIO voltage | VGPIO_ABS | -0.5 | V | Max VDDD + 0.5 V | 11 | ||
| Maximum current per GPIO | IGPIO_ABS | -25 | 25 | mA | 11 | ||
| GPIO injection current | IGPIO_injection | -0.5 | 0.5 | mA | Absolute max, current injected per pin | 11 | |
| OVT GPIO voltage | VGPIO_OVT_ABS | -0.5 | 6 | V | Applicable to pins HPI_INT and GPIO_1 | 11 | |
| ESD human body model | ESD_HBM | 2200 | V | 11 | |||
| ESD charged device model | ESD_CDM | 500 | V | 11 | |||
| Pin current for latch-up | LU | -100 | 100 | mA | 11 | ||
| ESD IEC61000-4-2 contact | ESD_IEC_CON | 8000 | V | Contact discharge on CC1, CC2, VBUS_IN, HPI_SDA and HPI_SCL pins | 11 | ||
| ESD IEC61000-4-2 air | ESD_IEC_AIR | 15000 | V | Air discharge for D+, D-, CC1, CC2, VBUS_IN, HPI_SDA and HPI_SCL pins | 11 | ||
| Power supply input voltage (sink mode) | VDDD | 2.7 | 5.5 | V | Sink mode, -40°C ≤ TA ≤ 105°C | 11 | |
| Power supply input voltage (source mode) | VDDD | 3 | 5.5 | V | Source mode, -40°C ≤ TA ≤ 105°C | 11 | |
| Power supply input voltage | VBUS_IN | 3 | 24.5 | V | -40 °C ≤ TA ≤ 105°C | 11 | |
| Power supply decoupling capacitor for VDDD | Cexc | 0.8 | 1 | µF | X5R ceramic or better | 11 | |
| Power supply decoupling capacitor for VBUS_IN_DISCHARGE | Cexv | 0.1 | µF | X5R ceramic or better | 11 | ||
| Operating ambient temperature | TA | -40 | 25 | 105 | °C | Extended Industrial | 20 |
| Operating junction temperature | TJ | -40 | 25 | 120 | °C | Extended Industrial | 20 |
| Package thermal resistance junction-to-ambient | θJA | 19.98 | °C/W | 24-QFN | 20 | ||
| Package thermal resistance junction-to-case | θJC | 4.78 | °C/W | 24-QFN | 20 | ||
| Wakeup from Deep Sleep mode | TDEEPSLEEP | 35 | µs | 12 | |||
| Power-up to ready to accept I2C/CC command | T_PWR_RDY | 5 | 25 | ms | 12 | ||
| Input voltage HIGH threshold | VIH_CMOS | 0.7 | V | CMOS input; min is 0.7 × VDDD | 12 | ||
| Input voltage LOW threshold | VIL_CMOS | 0.3 | V | CMOS input; max is 0.3 × VDDD | 12 | ||
| Output voltage HIGH level | VOH_3V | -0.6 | V | IOH = 4 mA at 3-V VDDD; min is VDDD -0.6 | 12 | ||
| Output voltage LOW level | VOL_3V | 0.6 | V | IOL = 10 mA at 3-V VDDD | 12 | ||
| Input leakage current (absolute value) | IIL | 2 | nA | +25°C TA, 3-V VDDD | 12 | ||
| Max pin capacitance D+, D- | CPIN_A | 22 | pF | Capacitance on D+, D- pins. Guaranteed by characterization. | 12 | ||
| Max pin capacitance, other I/Os | CPIN | 3 | 7 | pF | -40°C to +85°C TA, All VDDD, all other I/OS. Guaranteed by characterization. | 12 | |
| Input hysteresis CMOS | VHYSCMOS | 0.05 | mV | VDDD < 4.5 V. Guaranteed by characterization. Min is 0.05 × VDDD | 12 | ||
| ADC integral non-linearity | INL | -2.5 | 2.5 | LSB | Reference voltage generated from VDDD | 18 | |
| ADC integral non-linearity | INL | -1.5 | 1.5 | LSB | Reference voltage generated from bandgap | 18 | |
| ADC differential non-linearity | DNL | -2.5 | 2.5 | LSB | Reference voltage generated from VDDD | 18 | |
| ADC differential non-linearity | DNL | -1.5 | 1.5 | LSB | Reference voltage generated from bandgap | 18 | |
| ADC gain error | Gain Error | -1.5 | 1.5 | LSB | 18 | ||
| ADC reference voltage from band gap | VREF_ADC2 | 1.96 | 2 | 2.04 | V | Reference voltage generated from bandgap | 18 |
| ADC slew rate of sampled voltage signal | SLEW_Max | 3 | V/ms | 18 | |||
| Core logic output voltage | VCCD | 1.8 | V | 11 | |||
| Active mode supply current from VBUS or VDDD | IDD_A | 10 | mA | VDDD = 5 V OR VBUS = 5 V, TA = 25°C. CC1/CC2 in Tx or Rx, no I/O sourcing current, 2 SCBs at 1 Mbps, EA/ADC/CSA/UVOV ON, CPU at 24 MHz. | 12 | ||
| Sleep mode supply current | IDD_S | 3 | mA | VDDD = 3.3 V, TA = 25°C, All blocks except CPU are on, CC IO on, EA/ADC/CSA/UVOV On. | 12 | ||
| Deep sleep supply current (sink) | IDD_PB_DS_A_SNK | 500 | µA | For sink applications, VBUS = 24.5 V, TA = 25 °C, Part is in deep sleep. Attached, CC I/O on, ADC/CSA/UVOV on. | 12 | ||
| Wakeup from sleep mode | TSLEEP | 0 | µs | 12 | |||
| Power-on I/O Initialization Time | TPOR_HIZ_T | 3 | ms | 12 | |||
| ADC resolution | Resolution | 8 | Bits | 18 |
CAD (KiCad official)
- Symbol:
CYPD3177-24LQXQT - Footprint:
Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm - 3D model: QFN-24(4x4) (KiCad packages3D, STEP)
- 3D model files:
cypd3177-24lqxqt-etched.step/cypd3177-24lqxqt-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);cypd3177-24lqxqt.step/cypd3177-24lqxqt.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: INFINEON TECHNOLOGIES datasheet (24 pp, sha256
56daea80a843fc73, retrieved 2026-11-17, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-opus-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).