220 Ω Resistor 0402 - Bourns CR0402-FX-2200GLF

{
 "schema": "adom/mark-plan@1",
 "mpn": "CR0402-FX-2200GLF",
 "step": "/home/adom/project/basic-parts-overhaul/pages/cr0402-fx-2200glf/CR0402-FX-2200GLF-unetched.step",
 "footprint": "/home/adom/project/basic-parts-overhaul/pages/cr0402-fx-2200glf/CR0402-FX-2200GLF.kicad_mod",
 "standUp": [],
 "standUpSource": "as-is (Z up)",
 "face": "top",
 "pin1": {
  "source": "footprint pad 1",
  "xyMm": [
   -0.5,
   -0.0
  ],
  "corner": "left/middle"
 },
 "existingMarks": [],
 "vendorMarking": {
  "present": false,
  "glyphFaces": 0
 },
 "faceNormal": [
  0,
  0,
  1
 ],
 "longAxis": {
  "axis": "x",
  "vector": [
   1.0,
   0.0,
   0.0
  ],
  "why": "two-terminal part: along the body, pad 1 to pad 2 (between the terminations)",
  "override": null
 },
 "readingDirection": {
  "vector": [
   1.0,
   0.0,
   0.0
  ],
  "angleDeg": 0,
  "textUp": [
   -0.0,
   1.0,
   0.0
  ],
  "rule": "pin 1 / pad 1 at the start (left) of the text, and below it when it sits on a side"
 },
 "band": {
  "regionMm": [
   -0.3,
   -0.23,
   0.3,
   0.23
  ],
  "zMm": 0.32,
  "lengthMm": 0.6,
  "heightMm": 0.46,
  "why": "highest flat face over the body centre",
  "terminationsExcludedBy": null,
  "trimmedEnds": [],
  "keepouts": [],
  "sideTurn": null,
  "margins": {
   "lengthEachSide": 0.12,
   "heightEachSide": 0.15
  }
 },
 "text": {
  "lines": [
   "CR0402-",
   "FX-2200GLF"
  ],
  "chars": 17,
  "capHeightMm": 0.0569,
  "smallestLineMm": 0.0569,
  "heightPctOfBand": 28.4,
  "why": "two lines: the smaller line (0.057 mm) beats one line (0.033 mm) by 1.72x",
  "alternative": {
   "lines": [
    "CR0402-FX-2200GLF"
   ],
   "capHeightMm": 0.0331,
   "smallestLineMm": 0.0331
  },
  "font": "service-step2glb /laser-etch (single-stroke outline font)"
 },
 "etch": {
  "poseQuarterTurnsZ": 0,
  "service": "/laser-etch?mode=flat",
  "note": "turn so the reading direction is +X, etch, fit the mark into the band, turn back"
 },
 "outline": {
  "upAxis": "z",
  "poseRotZDeg": 180,
  "rot": 180,
  "recipe": "adom-aiflow-etch outline <part.step> --footprint <part.kicad_mod> --mpn CR0402-FX-2200GLF (stands the STEP up (as-is (Z up)), turns it 180 deg about Z and draws CR0402- / FX-2200GLF on the planned band, rot 180)",
  "why": "iso camera looks from +X+Y+Z: text along +Y (rot 90) or -X (rot 180) reads left to right with pin 1 toward the viewer"
 },
 "widget": {
  "px": 320,
  "pxPerMm": 271.53,
  "capHeightPx": 12.6
 },
 "hints": [],
 "warnings": [],
 "summary": "Mark along the 0.60 mm axis (+X), 0.06 mm text (2 lines), upright with pin 1 left middle, outline rot 180 after a 180 deg pose turn; ~13 px caps at 320 px"
}