main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs bq51050brhlr: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
viewers bq51050brhlr: viewers · Ray
bq51050brhlr-etched.fit.json bq51050brhlr: one-pass backfill (re-etched, hero rebuilt in-pass (inputs changed)) · Ray
bq51050brhlr-etched.glb bq51050brhlr: one-pass backfill (re-etched, hero rebuilt in-pass (inputs changed)) · Ray
bq51050brhlr-etched.step bq51050brhlr: one-pass backfill (re-etched, hero rebuilt in-pass (inputs changed)) · Ray
bq51050brhlr-hero.glb bq51050brhlr: hero from the plain model · Ray
bq51050brhlr-hero.overlay.json bq51050brhlr: hero from the plain model · Ray
bq51050brhlr.glb Publish 0.1.0 · Ray
bq51050brhlr.kicad_mod Publish 0.1.0 · Ray
bq51050brhlr.kicad_sym Publish 0.1.0 · Ray
bq51050brhlr.lbr Publish 0.1.0 · Ray
bq51050brhlr.step Publish 0.1.0 · Ray
package.json Publish 0.1.1 · Ray
page.json Publish 0.1.1 · Ray
README.md Initial commit: component/bq51050brhlr · Ray

BQ51050BRHLR

Texas Instruments · Battery Management · QFN-20-EP(3.7x4.7)

BQ51050BRHLR from Texas Instruments, in a QFN-20-EP(3.7x4.7). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 PGND power_in Power ground connection for the device.
2 AC1 input AC power input from receiver coil with maximum input voltage of 20V and 2A RMS current rating.
3 BOOT1 output Bootstrap output for driving high-side FETs of synchronous rectifier; connect 10-nF ceramic capacitor from BOOT1 to AC1.
4 BAT power_out Output pin delivering regulated power to battery at 4.20V with maximum 1.5A charging current.
5 CLAMP1 output Open-drain FET output for non-power dissipative overvoltage AC clamp protection; activates when RECT voltage exceeds 15V threshold.
6 COMM1 output Open-drain output for load modulation communication with primary; connect capacitor from COMM1 to AC1 for capacitive load modulation.
7 CHG output Open-drain status output active when BAT output is enabled with maximum 15mA sink current rating.
8 AD-EN output Push-pull driver output for external PFET control when wired charging is active; float if not used.
9 AD input Adapter voltage detection input with 3.6V typical presence threshold and maximum 30V rating; connect 1-µF capacitor to PGND or direct to PGND if unused.
10 TERM input Termination threshold programming input; sets termination current as percentage of programmed charge current IBULK.
11 EN2 input Priority control input between wireless power and wired power with 1.3V high threshold; EN2 low enables wired charging when AD present.
12 ILIM bidirectional Current programming pin where total resistance RILIM from ILIM to PGND sets charging current from 500mA to 1.5A; KILIM factor is 314 AΩ.
13 TS/CTRL input Temperature sense input for NTC thermistor monitoring with 2.2V internal bias voltage; connect NTC resistor to PGND or 10-kΩ resistor if NTC not used.
14 FOD input Foreign object detection power measurement input for WPC v1.2 compatibility with 0-5W received power measurement range.
15 COMM2 output Open-drain output for load modulation communication with primary; connect capacitor from COMM2 to AC2 for capacitive load modulation.
16 CLAMP2 output Open-drain FET output for non-power dissipative overvoltage AC clamp protection; activates when RECT voltage exceeds 15V threshold.
17 BOOT2 output Bootstrap output for driving high-side FETs of synchronous rectifier; connect 10-nF ceramic capacitor from BOOT2 to AC2.
18 RECT output Filtered rectifier output node; connect ceramic capacitor from 4.7µF to 22µF to PGND depending on power level.
19 AC2 input AC power input from receiver coil with maximum input voltage of 20V and 2A RMS current rating.
20 PGND power_in Power ground connection for the device.
21 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package QFN-20-EP(3.7x4.7)
Category Power Management (PMIC)
Pins 21

CAD (KiCad official)

  • Symbol: BQ51050BRHLR
  • Footprint: Package_DFN_QFN:QFN-20-1EP_4x5mm_P0.5mm_EP2.65x3.65mm
  • 3D model: QFN-20-EP(3.7x4.7) (KiCad packages3D, STEP)
  • 3D model files: bq51050brhlr-etched.step / bq51050brhlr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); bq51050brhlr.step / bq51050brhlr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (44 pp, sha256 38293c82dac0e8d1, retrieved 2026-09-22, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.2, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF