BLM15AX601SN1D

{
 "schema": "adom/mark-plan@1",
 "mpn": "BLM15AX601SN1D",
 "step": "/home/adom/project/basic-parts-overhaul/pages/blm15ax601sn1d/BLM15AX601SN1D-unetched.step",
 "footprint": "/home/adom/project/basic-parts-overhaul/pages/blm15ax601sn1d/BLM15AX601SN1D.kicad_mod",
 "standUp": [],
 "standUpSource": "--up z",
 "face": "top",
 "pin1": {
  "source": "footprint pad 1",
  "xyMm": [
   -0.425,
   -0.0
  ],
  "corner": "left/middle"
 },
 "existingMarks": [],
 "vendorMarking": {
  "present": false,
  "glyphFaces": 0
 },
 "faceNormal": [
  0,
  0,
  1
 ],
 "longAxis": {
  "axis": "x",
  "vector": [
   1.0,
   0.0,
   0.0
  ],
  "why": "two-terminal part: along the body, pad 1 to pad 2 (between the terminations)",
  "override": null
 },
 "readingDirection": {
  "vector": [
   1.0,
   0.0,
   0.0
  ],
  "angleDeg": 0,
  "textUp": [
   -0.0,
   1.0,
   0.0
  ],
  "rule": "pin 1 / pad 1 at the start (left) of the text, and below it when it sits on a side"
 },
 "band": {
  "regionMm": [
   -0.25,
   -0.21,
   0.25,
   0.21
  ],
  "zMm": 0.5,
  "lengthMm": 0.5,
  "heightMm": 0.42,
  "why": "highest flat face over the body centre",
  "terminationsExcludedBy": null,
  "trimmedEnds": [],
  "keepouts": [],
  "sideTurn": null,
  "margins": {
   "lengthEachSide": 0.12,
   "heightEachSide": 0.15
  }
 },
 "text": {
  "lines": [
   "BLM15AX",
   "601SN1D"
  ],
  "chars": 14,
  "capHeightMm": 0.0683,
  "smallestLineMm": 0.0683,
  "heightPctOfBand": 37.4,
  "why": "two lines: the smaller line (0.068 mm) beats one line (0.034 mm) by 2.03x",
  "alternative": {
   "lines": [
    "BLM15AX601SN1D"
   ],
   "capHeightMm": 0.0336,
   "smallestLineMm": 0.0336
  },
  "font": "service-step2glb /laser-etch (single-stroke outline font)"
 },
 "etch": {
  "poseQuarterTurnsZ": 0,
  "service": "/laser-etch?mode=flat",
  "note": "turn so the reading direction is +X, etch, fit the mark into the band, turn back"
 },
 "outline": {
  "upAxis": "z",
  "poseRotZDeg": 180,
  "rot": 180,
  "recipe": "adom-aiflow-etch outline <part.step> --footprint <part.kicad_mod> --mpn BLM15AX601SN1D (stands the STEP up (--up z), turns it 180 deg about Z and draws BLM15AX / 601SN1D on the planned band, rot 180)",
  "why": "iso camera looks from +X+Y+Z: text along +Y (rot 90) or -X (rot 180) reads left to right with pin 1 toward the viewer"
 },
 "widget": {
  "px": 320,
  "pxPerMm": 271.53,
  "capHeightPx": 15.1
 },
 "hints": [],
 "warnings": [],
 "summary": "Mark along the 0.50 mm axis (+X), 0.07 mm text (2 lines), upright with pin 1 left middle, outline rot 180 after a 180 deg pose turn; ~15 px caps at 320 px"
}