AP2900TB-A1

{
 "schema": "adom.pads/1",
 "slug": "ap2900tb-a1",
 "footprint": "SOT-23-5",
 "generated_from": {
  "footprint": "SOT-23-5@sha256:455a3f7c3e5eb5b8",
  "pins": "page.json:component.pins",
  "overrides": null
 },
 "pin1": {
  "pad": "1",
  "at": [
   -1.1375,
   -0.95
  ],
  "corner": "top-left",
  "source": "silk-marker",
  "derived_from": "SOT-23-5@sha256:455a3f7c3e5eb5b8"
 },
 "pad_count": 5,
 "symbol_pins": [
  "1",
  "2",
  "3",
  "4",
  "5"
 ],
 "paste_apertures": 0,
 "issues": [],
 "pads": [
  {
   "pad": "1",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -1.1375,
    -0.95
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "1",
   "name": "VIN",
   "type": "power_in",
   "description": "Input supply voltage, 6 V to 40 V operating (42 V absolute max). Requires a low-ESR decoupling capacitor (1 uF X5R/X7R MLCC in parallel with a 100 uF electrolytic recommended) placed as close as possible between VIN and GND to supply AC current to the internal power MOSFETs.",
   "is_pin1": true,
   "source": {
    "geometry": "SOT-23-5.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "2",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -1.1375,
    0.0
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "2",
   "name": "GND",
   "type": "power_in",
   "description": "Ground pin. Common return for internal control circuitry and the low-side synchronous MOSFET source. Recommended to connect to the ground copper plane via vias for good thermal dissipation and noise suppression.",
   "is_pin1": false,
   "source": {
    "geometry": "SOT-23-5.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "3",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -1.1375,
    0.95
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "3",
   "name": "EN",
   "type": "input",
   "description": "Enable input. High level enables the IC, low level disables the IC (shutdown mode). Must not be tied directly to VIN, and must not be connected to VIN through a series resistor. Drive voltage must be kept below 5 V. Internally pulled up by an approximate 50 uA current source to ~4.5 V, so the IC auto-starts if EN is left floating. If an external pull-down resistor is used to disable, it must be < 4.7 kΩ to guarantee a valid low.",
   "is_pin1": false,
   "source": {
    "geometry": "SOT-23-5.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "4",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    1.1375,
    0.95
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "4",
   "name": "FB",
   "type": "input",
   "description": "Feedback input. Connect to the midpoint of the external output feedback divider to program the output voltage (VFB reference 1.2 V typ). Route away from the SW switching node to minimize noise pickup.",
   "is_pin1": false,
   "source": {
    "geometry": "SOT-23-5.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "5",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    1.1375,
    -0.95
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "5",
   "name": "SW",
   "type": "output",
   "description": "Switch node. Drain of the internal high-side P-MOSFET and source of the low-side N-MOSFET; connect to the external inductor with a short, wide, thick trace to minimize EMI and switching loss.",
   "is_pin1": false,
   "source": {
    "geometry": "SOT-23-5.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  }
 ]
}