component
AL8863SP-13
Public Made by Adomby adom
Diodes Incorporated LED Drivers, ESOP-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
Generated by kicad-footprint-generator · KiCad file format 20260206
| Name | Last updated |
|---|---|
| docs | 8d ago |
| viewers | 8d ago |
| al8863sp-13-etched.glb | 8d ago |
| al8863sp-13-etched.step | 8d ago |
| al8863sp-13-hero.glb | 8d ago |
| al8863sp-13-hero.overlay.json | 8d ago |
| al8863sp-13.glb | 8d ago |
| al8863sp-13.kicad_mod | 8d ago |
| al8863sp-13.kicad_sym | 8d ago |
| al8863sp-13.lbr | 8d ago |
| al8863sp-13.step | 8d ago |
| package.json | 8d ago |
| page.json | 8d ago |
| README.md | 8d ago |
AL8863SP-13
Diodes Incorporated · LED Drivers · ESOP-8
AL8863SP-13 from Diodes Incorporated, in a ESOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OSP | input | Output shorted protection input, used with CSN to detect an LED string short; if CSN-OSP stays below 1V for 23ms, FAULT goes low. |
| 2 | DIM | input | Multi-function on/off and brightness control: below 0.3V turns off output current, above 2.6V gives 100% of IOUT_NOM, and a PWM signal (low <0.3V, high >2.6V, transition time under 1µs) sets the output current up to 100%; a capacitor to ground increases soft-start time. |
| 3 | NTC | input | Connect an NTC resistor to GND to set the thermal fold-back break point, with fold-back starting when the NTC pin falls to 1.3V and a 100µA internal bias current. |
| 4 | GND | power_in | Ground reference for the device. |
| 5 | DRV | output | Gate driver output for the external switch Q1, with an absolute maximum pin voltage of -0.3V to +20V and a clamp voltage of 15V maximum. |
| 6 | VIN | power_in | Input voltage from 4.5V to 60V; decouple to ground with 10µF or higher X7R ceramic capacitor placed close to the device. |
| 7 | FAULT | output | Active-low, open-drain fault report pin that is asserted low for LED open circuit, LED short circuit or over-temperature and requires an external pull-up resistor (VFAULT_LOW maximum 700mV at 1mA). |
| 8 | CSN | input | Current sense negative input; the current sense resistor is connected between VIN and CSN for high-side sensing, with CSN input current of 16µA typical. |
| 9 | EP | passive | Exposed pad that must be connected to GND and thermal mass for enhanced thermal impedance, and should not be used as an electrical ground conduction path. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Diodes Incorporated |
| Package | ESOP-8 |
| Category | LED Drivers |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Voltage | VIN | 4.5 | 60 | V | 3 | ||
| Operating Frequency | fSW | 50 | 1000 | kHz | 3 | ||
| Operating Ambient Temperature | TA | -40 | 125 | °C | 3 | ||
| Input Voltage | VIN | -0.3 | 65 | V | 3 | ||
| CSN, FAULT, OSP Pin Voltage | VCSN, VFAULT, VOSP | -0.3 | 65 | V | 3 | ||
| DRV Pin Voltage | VDRV | -0.3 | 20 | V | 3 | ||
| DIM, NTC Pin Voltage | VDIM, VNTC | -0.3 | 5.5 | V | 3 | ||
| Operating Junction Temperature | TJ | -40 | 150 | °C | 3 | ||
| Storage Temperature Range | TSTG | -65 | 165 | °C | 3 | ||
| ESD Human-Body Model (HBM) | VESD | 2000 | V | 3 | |||
| ESD Charged-Device Model (CDM) | VESD | 750 | V | 3 | |||
| Input Voltage | VIN | 4.5 | 60 | V | 4 | ||
| Mean Current Sense Threshold Voltage | VSENSE | 95 | 100 | 105 | mV | Measured on CSN Pin with Respect to VIN | 4 |
| Gate Driver Output Voltage High | VGATE_HIGH | 9 | V | VIN = 12V, Sourcing 20mA | 4 | ||
| Gate Driver Output Voltage Low | VGATE_LOW | 0.5 | V | VIN = 12V, Sinking 20mA | 4 | ||
| Gate Driver Clamp Voltage | VGATE_CLAMP | 15 | V | VIN = 18V, Sourcing 20mA | 4 | ||
| Recommended PWM Dimming Frequency | fPWM | 0.1 | 20 | kHz | 4 | ||
| DIM Logic High Level | VDIM_HIGH | 2.6 | 5.5 | V | 4 | ||
| DIM Logic Low Level | VDIM_LOW | 0.3 | V | 4 | |||
| Recommended Maximum Switching Frequency | fSW_MAX | 1 | MHz | 4 | |||
| FAULT Output Low Voltage | VFAULT_LOW | 700 | mV | IFAULT = 1mA | 4 | ||
| NTC Internal Bias Current | IBIAS | 95 | 100 | 105 | µA | 4 | |
| Quiescent Current | IQ | 600 | µA | DIM pin floating | 4 | ||
| VIN UVLO Rising Threshold | UVLO | 4.3 | V | 4 | |||
| VIN UVLO Hysteresis | UVLO_HYS | 150 | mV | 4 | |||
| Sense Threshold Hysteresis | VSENSE_HYS | 13 | mV | 4 | |||
| CSN Pin Input Current | ICSN | 16 | µA | VCSN = VIN - 0.1 | 4 | ||
| Gate Driver Rising Time | tRISE | 100 | ns | VIN = 13V, C = 10nF | 4 | ||
| Gate Driver Falling Time | tFALL | 60 | ns | VIN = 13V, C = 10nF | 4 | ||
| Gate Driver High Side Resistance | RGH | 5.7 | Ω | IDRV = -20mA | 4 | ||
| Gate Driver Low Side Resistance | RGL | 2.2 | Ω | IDRV = 20mA | 4 | ||
| Recommended Minimum Switch ON Time For 4% Accuracy | tON_REC | 500 | ns | 4 | |||
| Internal Comparator Propagation Delay | tPD | 100 | ns | 4 | |||
| Output Short Threshold Voltage | V(CSN-OSP) | 1 | V | 4 | |||
| Delay Time for Fault Detection | tD | 23 | ms | 4 | |||
| NTC Upper Threshold Voltage | VNTC_HIGH | 1.3 | V | Thermal fold-back starts | 4 | ||
| NTC Lower Threshold Voltage | VNTC_LOWER | 1 | V | Thermal fold-back stops | 4 | ||
| Thermal Shutdown Threshold | TTSD | 165 | °C | 4 | |||
| Thermal Shutdown Hysteresis | TTSD_HYS | 30 | °C | 4 | |||
| Junction-to-Ambient Thermal Resistance | θJA | 56 | °C/W | Note 5: 2"*2" FR-4 PCB, 2oz copper, minimum top-layer pad with thermal vias | 4 | ||
| Junction-to-Case (Top) Thermal Resistance | θJC | 6 | °C/W | 4 |
CAD (KiCad official)
- Symbol:
AL8863SP-13 - Footprint:
Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.3mm - 3D model: ESOP-8 (KiCad packages3D, STEP)
- 3D model files:
al8863sp-13-etched.step/al8863sp-13-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);al8863sp-13.step/al8863sp-13.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Diodes Incorporated datasheet (13 pp, sha256
8cb2b6e6c79f8a82, retrieved 2026-10-18, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).