Generated by kicad-footprint-generator · KiCad file format 20260206
ADUM5000WARWZ
Analog Devices · DC-DC Converters · SOIC-16-300mil
ADUM5000WARWZ from Analog Devices, in a SOIC-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDD1 | power_in | Primary supply voltage of 3.0 V to 5.5 V; pins 1 and 7 are internally connected and both should be externally connected to a common power source. |
| 2 | GND1 | power_in | Ground reference for the primary side of the converter; pins 2 and 8 are internally connected and both should be connected to a common ground. |
| 3 | NC | unconnected | No internal connection. |
| 4 | RCIN | input | Regulation control input that is weakly pulled low; in slave mode (RCSEL low) it connects to a master RCOUT or is tied low to disable the converter, and it must not be tied high while RCSEL is low. |
| 5 | RCOUT | output | Regulation control output that, in master configuration, connects to the RCIN pin of a slave isoPower device to regulate it. |
| 6 | RCSEL | input | Control input that selects self-regulating master mode (high) or slave mode (low); it is weakly pulled high and should be tied high or low in noisy environments. |
| 7 | VDD1 | power_in | Primary supply voltage of 3.0 V to 5.5 V; internally connected to pin 1 and recommended to be externally connected to the same power source. |
| 8 | GND1 | power_in | Ground reference for the primary side of the converter; internally connected to pin 2 and recommended to be connected to the same ground. |
| 9 | GNDISO | power_in | Ground reference for the secondary side of the converter; pins 9 and 15 are internally connected and both should be connected to a common ground. |
| 10 | VISO | power_out | Secondary supply output for external loads of 3.3 V (VSEL low) or 5.0 V (VSEL high); 5.0 V is not guaranteed with a 3.3 V primary input, and pins 10 and 16 are internally connected and should both be connected externally. |
| 11 | NC | unconnected | No internal connection. |
| 12 | NC | unconnected | No internal connection. |
| 13 | VSEL | input | Output voltage select: VISO setpoint is 5.0 V when VSEL = VISO and 3.3 V when VSEL = GNDISO; it is weakly pulled high, should be tied high or low in noisy environments, and has no function in slave regulation mode. |
| 14 | NC | unconnected | No internal connection. |
| 15 | GNDISO | power_in | Ground reference for the secondary side of the converter; internally connected to pin 9 and recommended to be connected to the same ground. |
| 16 | VISO | power_out | Secondary supply output for external loads of 3.3 V or 5.0 V per VSEL; internally connected to pin 10 and connecting both externally is recommended. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | SOIC-16-300mil |
| Category | Power Management ICs |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Storage Temperature | TST | -55 | 150 | °C | 7 | ||
| Ambient Operating Temperature | TA | -40 | 105 | °C | 7 | ||
| Supply Voltages (VDDx, VISO) | VDDx, VISO | -0.5 | 7 | V | Each voltage relative to its respective ground | 7 | |
| Input Voltage (RCSEL, RCIN, VSEL) | RCSEL, RCIN, VSEL | -0.5 | V | Upper limit VDDI + 0.5 V as printed (VDDI = input-side supply) | 7 | ||
| Output Voltage (RCOUT) | RCOUT | -0.5 | V | Upper limit VDDO + 0.5 V as printed (VDDO = output-side supply) | 7 | ||
| Average Total Output Current | IISO | 100 | mA | See Figure 2 for derating vs. temperature | 7 | ||
| Common-Mode Transients | -100 | 100 | kV/µs | Across the isolation barrier | 7 | ||
| Operating Temperature | TA | -40 | 105 | °C | Operation at 105°C requires reduction of maximum load current per Table 10 | 6 | |
| Supply Voltage VDD1 at VSEL = 0 V | VDD1 | 2.7 | 5.5 | V | VSEL = 0 V; relative to GND1 | 6 | |
| Supply Voltage VDD1 at VSEL = 5 V | VDD1 | 4.5 | 5.5 | V | VSEL = 5 V; relative to GND1 | 6 | |
| Setpoint (5 V primary / 5 V secondary) | VISO | 4.7 | 5 | 5.4 | V | IISO = 0 mA | 3 |
| Load Regulation (5 V primary / 5 V secondary) | VISO(LOAD) | 1 | 5 | % | IISO = 8 mA to 72 mA | 3 | |
| IDD1 Supply Current, No VISO Load (5 V / 5 V) | IDD1(Q) | 4 | 15 | mA | IISO = 0 mA | 3 | |
| Setpoint (3.3 V primary / 3.3 V secondary) | VISO | 3 | 3.3 | 3.6 | V | IISO = 0 mA | 3 |
| Load Regulation (3.3 V primary / 3.3 V secondary) | VISO(LOAD) | 1 | 5 | % | IISO = 4 mA to 36 mA | 3 | |
| IDD1 Supply Current, No VISO Load (3.3 V / 3.3 V) | IDD1(Q) | 3 | 12 | mA | IISO = 0 mA | 3 | |
| Setpoint (5 V primary / 3.3 V secondary) | VISO | 3 | 3.3 | 3.6 | V | IISO = 0 mA | 4 |
| Load Regulation (5 V primary / 3.3 V secondary) | VISO(LOAD) | 1 | 5 | % | IISO = 10 mA to 100 mA | 4 | |
| IDD1 Supply Current, No VISO Load (5 V / 3.3 V) | IDD1(Q) | 3 | 12 | mA | IISO = 0 mA | 4 |
CAD (KiCad official)
- Symbol:
ADUM5000WARWZ - Footprint:
Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm - 3D model: SOIC-16-300mil (KiCad packages3D, STEP)
- 3D model files:
adum5000warwz-etched.step/adum5000warwz-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);adum5000warwz.step/adum5000warwz.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (15 pp, sha256
5197f63a91ac6d0d, retrieved 2026-11-17) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).