3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownADM3307EACPZ
Analog Devices · RS232 ICs · LFCSP-32(5x5)
ADM3307EACPZ from Analog Devices, in a LFCSP-32(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EN | input | Receiver enable; a high level three-states all receiver outputs, with ±15 kV ESD protection on the ADM3307E. |
| 2 | SD | input | Shutdown control; a high level disables the charge pump and transmitters and cuts quiescent current to less than 1 µA, with ROUT3 remaining active. |
| 3 | NC | unconnected | No connect; do not connect to this pin. |
| 4 | T1IN | input | Transmitter 1 input accepting TTL/CMOS levels, with an internal 400 kΩ pull-up resistor to VCC. |
| 5 | T2IN | input | Transmitter 2 input accepting TTL/CMOS levels, with an internal 400 kΩ pull-up resistor to VCC. |
| 6 | T3IN | input | Transmitter 3 input accepting TTL/CMOS levels, with an internal 400 kΩ pull-up resistor to VCC. |
| 7 | T4IN | input | Transmitter 4 input accepting TTL/CMOS levels, with an internal 400 kΩ pull-up resistor to VCC. |
| 8 | T5IN | input | Transmitter 5 input accepting TTL/CMOS levels, with an internal 400 kΩ pull-up resistor to VCC. |
| 9 | NC | unconnected | No connect; do not connect to this pin. |
| 10 | R1OUT | output | Receiver 1 output at TTL/CMOS levels, three-stated when EN is high. |
| 11 | R2OUT | output | Receiver 2 output at TTL/CMOS levels, three-stated when EN is high. |
| 12 | R3OUT | output | Receiver 3 output at TTL/CMOS levels, which stays active in shutdown when EN is low. |
| 13 | NC | unconnected | No connect; do not connect to this pin. |
| 14 | R3IN | input | Receiver 3 input accepting RS-232 levels (±25 V range), with an internal 5 kΩ pull-down to GND. |
| 15 | R2IN | input | Receiver 2 input accepting RS-232 levels (±25 V range), with an internal 5 kΩ pull-down to GND. |
| 16 | R1IN | input | Receiver 1 input accepting RS-232 levels (±25 V range), with an internal 5 kΩ pull-down to GND. |
| 17 | T5OUT | output | Transmitter 5 RS-232 output, typically ±5.5 V, with ±15 kV ESD protection. |
| 18 | T4OUT | output | Transmitter 4 RS-232 output, typically ±5.5 V, with ±15 kV ESD protection. |
| 19 | T3OUT | output | Transmitter 3 RS-232 output, typically ±5.5 V, with ±15 kV ESD protection. |
| 20 | T2OUT | output | Transmitter 2 RS-232 output, typically ±5.5 V, with ±15 kV ESD protection. |
| 21 | T1OUT | output | Transmitter 1 RS-232 output, typically ±5.5 V, with ±15 kV ESD protection. |
| 22 | GND | power_in | Ground pin, must be connected to 0 V. |
| 23 | GND | power_in | Ground pin, must be connected to 0 V. |
| 24 | V- | power_out | Internally generated negative supply of -7.25 V, with capacitor C5 connected between GND and V-. |
| 25 | C3- | passive | Negative terminal of external charge pump capacitor C3, 0.1 µF recommended and up to 1 µF. |
| 26 | C1+ | passive | Positive terminal of external charge pump capacitor C1, 0.1 µF recommended and up to 1 µF. |
| 27 | C3+ | passive | Positive terminal of external charge pump capacitor C3, 0.1 µF recommended and up to 1 µF. |
| 28 | C2+ | passive | Positive terminal of external charge pump capacitor C2, 0.1 µF recommended and up to 1 µF. |
| 29 | V+ | power_out | Internally generated positive supply of 7.25 V, with capacitor C4 connected between VCC and V+. |
| 30 | VCC | power_in | Power supply input, 2.7 V to 3.6 V. |
| 31 | C2- | passive | Negative terminal of external charge pump capacitor C2, 0.1 µF recommended and up to 1 µF. |
| 32 | C1- | passive | Negative terminal of external charge pump capacitor C1, 0.1 µF recommended and up to 1 µF. |
| 33 | EP | power_in | Exposed pad, connected to ground. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | LFCSP-32(5x5) |
| Category | Communication Interface Chip/UART/485/232 |
| Pins | 33 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating Temperature Range (Industrial, A Version) | -40 | 85 | °C | 6 | |||
| Supply Voltage VCC (operating) | VCC | 2.7 | 3.6 | V | Single supply | 9 | |
| VCC | VCC | -0.3 | 4 | V | TA = 25°C | 6 | |
| V+ | V+ | 9 | V | (VCC − 0.3 V) to +9 V | 6 | ||
| V− | V− | -9 | V | +0.3 V to −9 V | 6 | ||
| Input Voltage TIN | TIN | -0.3 | 6 | V | 6 | ||
| Input Voltage RIN | RIN | -30 | 30 | V | 6 | ||
| Output Voltage TOUT | TOUT | -15 | 15 | V | 6 | ||
| Output Voltage ROUT | ROUT | -0.3 | V | −0.3 V to (VCC + 0.3 V) | 6 | ||
| Storage Temperature Range | -65 | 150 | °C | 6 | |||
| Lead Temperature (Soldering) | 300 | °C | 10 sec | 6 | |||
| ESD Rating IEC 1000-4-2 Air (RS-232 I/Os) | -15 | 15 | kV | 6 | |||
| ESD Rating IEC 1000-4-2 Contact (RS-232 I/Os) | -8 | 8 | kV | 6 | |||
| Thermal Impedance θJA, LFCSP_WQ (CP-32-7) | θJA | 32.5 | °C/W | 6 | |||
| Maximum Data Rate (ADM3307E, VCC = 2.7 V) | 250 | 720 | kbps | RL = 3 kΩ to 7 kΩ, CL = 50 pF to 1000 pF, VCC = 2.7 V | 5 | ||
| Maximum Data Rate (ADM3307E, VCC = 3.0 V) | 460 | 920 | kbps | RL = 3 kΩ to 7 kΩ, CL = 50 pF to 1000 pF, VCC = 3.0 V | 5 | ||
| Receiver Propagation Delay | TPHL, TPLH | 0.3 | µs | CL = 150 pF | 5 | ||
| Receiver Propagation Delay (ADM3307E only) | TPHL, TPLH | 0.17 | 1 | µs | CL = 150 pF; ADM3307E only | 5 | |
| Receiver Output Enable Time | tER | 100 | ns | 5 | |||
| Receiver Output Disable Time | tDR | 300 | ns | 5 | |||
| Transmitter Propagation Delay | TPHL, TPLH | 500 | ns | RL = 3 kΩ, CL = 1000 pF | 5 | ||
| Transition Region Slew Rate | 3 | 18 | V/µs | RL = 3 kΩ, CL = 50 pF to 1000 pF; measured at +3 V to −3 V or −3 V to +3 V | 5 | ||
| ESD Protection (I/O pins), Human body model | -15 | 15 | kV | Human body model | 5 | ||
| ESD Protection (I/O pins), IEC 1000-4-2 air discharge | -15 | 15 | kV | IEC 1000-4-2 air discharge | 5 | ||
| ESD Protection (I/O pins), IEC 1000-4-2 contact discharge | -8 | 8 | kV | IEC 1000-4-2 contact discharge; includes CMOS I/O, SD, and EN for ADM3307E | 5 | ||
| Maximum ICC (supply current) | ICC | 1.5 | mA | Product selection guide, ADM3307E | 7 |
CAD (KiCad official)
- Symbol:
ADM3307EACPZ - Footprint:
Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm - 3D model: LFCSP-32(5x5) (KiCad packages3D, STEP)
- 3D model files:
adm3307eacpz-etched.step/adm3307eacpz-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);adm3307eacpz.step/adm3307eacpz.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (20 pp, sha256
19555870393bbfda, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text+vision), consensusclaude-opus-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).